Ozito SCMS-8STANDU Manual

Ozito savemaskine SCMS-8STANDU

Læs gratis den danske manual til Ozito SCMS-8STANDU (2 sider) i kategorien savemaskine. Denne vejledning er vurderet som hjælpsom af 21 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 11 anmeldelser. Har du et spørgsmål om Ozito SCMS-8STANDU, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

ASSEMBLY OF STAND

SLIDING

COMPOUND MITRE

SAW & STAND

210mm (8¼”)

ORIGINAL INSTRUCTIONS

STAND ASSEMBLY

STAND

FASTENERS

The stand is constructed by assembling each half of the structure and

then joining them together.

7 Bolt Small - 36 pc

8 Washer Small - 36 pc

9 Nut Small - 36 pc

10 Rubber Foot - 4 pc

11 Bolt Large with Rubber

Stopper - 4 pc

12 Saw Mounting Bolts - 4 pc

1 Short Upper Support - 2 pc

2 Short Lower Support - 2 pc

3 Long Upper Support - 2 pc

4 Long Lower Support - 2 pc

5 Upper Leg - 4 pc

6 Lower Leg - 4 pc

1197 10

2 3 4 5

x4 x4

1 Remove the stand components

from the box and group matching

pieces together. Check that you

have all the contents listed to the

left.

Note: All upper members can be

identied by the 2 holes very close

together.

2 Lay two upper and lower legs on

the ground aligning 2 of the bolt

holes, parallel to each other.

The upper leg sits outside the

lower leg.

3 Place one long lower support

in between the legs and align

the bolt holes. The side support

should have its lip on the high side

(facing up) and should sit inside

the legs.

Ensure the lip with the lengthened

bolt holes is facing upwards.

4 Once aligned, insert small bolts

into the 2 aligned holes at both

sides of the lower support. Insert

the bolt from the outside and

screw a small washer and nut

onto each bolt to secure (only

hand tight at this initial stage).

5 Place one long upper support on

the of the legs at the top outside

(This will ensure the mounting

holes will align correctly once

assembled)

Insert a bolt from the outside into

the 2 aligned holes at either side

of the upper support and hand

tighten a small washer and nut

onto each.

6 At this stage your frame should

look like this.

128

SCMS-8STANDU

Art.-No.: 30.003.16 I.-No.: 11017

Produkt Specifikationer

Mærke:	Ozito
Kategori:	savemaskine
Model:	SCMS-8STANDU

Har du brug for hjælp?

Hvis du har brug for hjælp til Ozito SCMS-8STANDU stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

savemaskine Ozito Manualer

Ozito ECS-406A Manual

6 Oktober 2024

Ozito PXCCSK-4182 Manual

6 September 2024

Ozito PXBPCK-1825 Manual

6 September 2024

Ozito PXTCSK-2520 Manual

6 September 2024

Ozito PXPRSS-018 Manual

5 September 2024

Ozito PXBPCS-1815 Manual

5 September 2024

Ozito JSW-6100U Manual

21 August 2024

Ozito RTB-003 Manual

20 August 2024

Ozito RSW-5200 Manual

17 August 2024

Ozito JSW-4000U Manual

17 August 2024

savemaskine Manualer

Nyeste savemaskine Manualer

Einhell GE-CS 18 Li Manual

15 Oktober 2024

15 Oktober 2024

15 Oktober 2024

14 Oktober 2024

13 Oktober 2024

Einhell TC-AP 650 E Manual

12 Oktober 2024

Einhell TE-SM 36/210 Li Solo Manual

11 Oktober 2024

Einhell BT-SM 2534 Manual

11 Oktober 2024

Hitachi C 7MFA(LA) Manual

9 Oktober 2024

Ferrex DX254TS Manual

5 Oktober 2024