Paasche MIL-3AS Manual

Paasche Ikke kategoriseret MIL-3AS

Læs gratis den danske manual til Paasche MIL-3AS (3 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 30 personer og har en gennemsnitlig bedømmelse på 4.0 stjerner ud af 15.5 anmeldelser. Har du et spørgsmål om Paasche MIL-3AS, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

INSTRUCTIONS AND PARTS LIST MIL-8/06/2019

MIL – Airbrush

Double Action - Internal Mix

Siphon Feed

INTRODUCTlON:

Paasche® model MIL features hand crafted

construction using quality materials. The body

is machined brass, polished and chrome plated.

Fluid tips are nickel silver, needles are stainless

steel & the needle packing is PTFE. Preferred

by professional and hobbyist alike.

Airbrush Operation:

1. Press down on Trigger to release air and pull back on Trigger to control quantity of color.

2. To spray a ne line without heavy ends, start moving the airbrush without release of color. Then start

the color at the beginning of line and stop the color at the end, but continue the motion of the airbrush

after the color has stopped.

3. Practice until you can spray a ne line or a broad pattern without heavy build up at the beginning or

end of your strokes.

4. Speed of movement controls density of color and fading e󰀨ects at beginning and end of strokes.

5. For detail, hold the airbrush very close to the surface and then push down for air and pull back very

slowly on the Trigger to release a small amount of paint.

6. For background work and broad e󰀨ects, hold the airbrush away from the work surface and pull back

on Trigger to release required amount of color.

Head Sizes - Patterns - Fluid Thickness

Size 1 Size 3 Size 5 - Tip size .55mm -Tip size .73mm -Tip Size 1.06mm

- Pencil Line to 1’’ patterns -1/16’’ to 1-1/2’’ patterns-1/32’’ to 1-1/2’’ patterns

-thinner Paint than 3 & 5 -Thicker paint than size 1 -Thicker paint than size 3

Working Pressures:

• Operating pressures 20-55 PSI; Maximum pressure 75 PSI

• 20-30 PSI is best for detail spraying w/ properly thinned paint

• Use higher pressures for thicker material where ne detail is not critical

Equipment Set-up:

The Airbrush is held in the same manner as a pen, with the index nger comfortably over the Trigger.

1. Attach airhose to air supply and to airbrush. If using a regulator, set pressure between 20 -30 PSI.

2. Attach the color cup or bottle assembly to color socket.

REMOVING/REPLAClNG THE NEEDLE AND HANDLE :

1. Unscrew the handle and loosen the Locknut #12 by turning counterclockwise. Depress the Trigger

#7 and hold in Down position while removing or inserting the needle. This assures the needle moves

freely through the trigger. Gently remove the needle, rotating if necessary, Do NOT force out!

2. Inspect the condition of the needle. If it is bent or misshapen in any way, replace it with a new needle.

A bent needle can damage or split the Tip #4 causing bubbles or a rough spray pattern.

3. Hold trigger in DOWN position, insert the new needle into the Rocker Assembly #9. Gently push

needle through, rotating if necessary. until the needle stops in the front of the tip.

4. Release trigger and tighten locknut by turning clockwise.

REPLACING THE TRIGGER:

( If the Trigger #8 is removed, it must be replaced inside the airbrush shell, before the Rocker Assembly #9

and needle are re-inserted. )

1. Hold the trigger so the opening in the lever is in-line with the opening in the end of the airbrush shell

and the at side of the trigger stem is to the rear.

2. Insert trigger so the bottom of the stem covers the round top of the valve plunger.

REPLACING THE TIP:

1. Remove handle, loosen Locknut #12 and withdraw needle about one inch (1”).

2. Un-screw the Head #3 and remove. The Tip #4 can now be easily removed by hand. If stuck in shell tap

lightly with wrench.

3. Place a new tip into position and tighten head to shell . Push needle forward until it with a wrench

seats fully forward in tip and tighten locknut.

PERSONAL SETTINGS:

1. Needle Adjustment Sleeve - Used to increase or decrease spring tension for the trigger pull back.

Thread into the shell until the trigger stroke feels comfortable. Threading in until it stops can cause

the trigger to jam.

Produkt Specifikationer

Mærke:	Paasche
Kategori:	Ikke kategoriseret
Model:	MIL-3AS

Har du brug for hjælp?

Hvis du har brug for hjælp til Paasche MIL-3AS stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Paasche Manualer

Paasche 2000SI Manual

22 August 2024

Paasche VL-1AS Manual

22 August 2024

Paasche TS-3AS Manual

22 August 2024

Paasche D220R Manual

22 August 2024

Paasche VL-100D Manual

22 August 2024

Paasche RG-3AS Manual

22 August 2024

Paasche TG-1AS Manual

22 August 2024

Paasche H-100D Manual

22 August 2024

Paasche FP-1/32 Manual

22 August 2024

Paasche H-3AS Manual

22 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Vaxis Litecomm 8S Manual

6 December 2025

Advantech ABDNA-ER-IN5010 Manual

6 December 2025

ELO I-Series 4 E747123 Manual

6 December 2025

Bosch SPV4EMX24F Manual

6 December 2025

Compex Sport Elite Manual

6 December 2025

Fostex P650K Manual

6 December 2025

Opticis DVFC-100 Manual

6 December 2025

Fostex P800K Manual

6 December 2025

Bosch WAN24055PL Manual

6 December 2025

Zotac GAMING GeForce RTX 5060 Ti 16GB Twin Edge Manual

6 December 2025