Paasche 2000SI Manual

Paasche Ikke kategoriseret 2000SI

Læs gratis den danske manual til Paasche 2000SI (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 35 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 18 anmeldelser. Har du et spørgsmål om Paasche 2000SI, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

INTRODUCTION:

e SI Airbrush is simple in design and operation. Ideal for Hobbyists and Craers that are just learning to use an Airbrush. Available

o the shelf as size #3 with size #1 and #5 components available for your assembly. PTFE Packings.

OPERATING INSTRUCTIONS:

Adjustments in the ow of color are made by turning the Needle Chuck (#9) in to decrease, or out for increased ow. To spray,

press the Trigger (#6). To disassemble, loosen the Needle Locknut (#10) by holding the Needle Chuck (#9) rmly so it will not turn.

Unscrew the Needle Chuck from the Handle (#7) and remove the Handle. Now carefully remove the Needle (#16) and then the

Finger Button Assembly. e Head (#2) and Tip (#3) may now be removed. Reassembly should always be done with care, especially

when reinserting the Needle. Reverse the procedure used for disassembly. Aer the Needle has been gently pushed forward into

the tip, assemble the Needle Chuck (#9) and screw it in rmly. Hold the Needle Chuck while screwing the Needle Locknut (#10)

down to lock the needle. Caution should always be used when reinserting the Needle - too much pressure can damage the tip.

ADJUSTING OR REPLACING WORN PACKING WASHER:

1. If PTFE Packing & Packing Nut (#5) become worn or loose they must be tightened or replaced.

2. When replacing your PTFE Packing press Packing into the Packing Nut (#5). Use a small screwdriver to tighten packing nut

into shell until it is tight then back out one-half turn, may vary.

3. Now insert Trigger then Needle - you should feel a slight resistance to the needle as it goes through packing. If too loose/tight

adjust the Packing Nut with screwdriver until some slight resistance. Replace the Needle Chuck and the Needle Locknut.

Head Sizes - Patterns - Fluid Thickness

Size 1 - Tip size .022 inches or .55mm

- Used for ne detail. Pencil Line to 1’’ patterns

- Paint must be thinned further than 3 & 5 heads

Size 3 - Tip size .029 inches or .73mm

- Less detail than the size 1 head. 1/32’’ to 1-1/2’’ patterns

- Can spray slightly thicker paint than size 1 head

Size 5 - Tip Size .042 inches or 1.06mm

- Less detail than the size 3 head. 1/16’’ to 2’’ patterns

- Can spray slightly thicker paint than size 3 head

Working Pressures:

• Operating pressures 20-55 PSI; Maximum pressure 75 PSI

• 20-30 PSI is best for detail spraying w/ properly thinned paint

• Use the higher pressures for thicker material where ne detail is not critical or thin the paint to allow lower pressures.

Equipment Set-up:

e Airbrush is held in the same manner as a pen, with the index nger comfortably over the Trigger.

1. Attach airhose to air supply and to airbrush. If using a regulator, set pressure between 20 -30 PSI.

2. Attach the color cup or bottle assembly to color socket.

3. Spray with needle protecting cap #1 on or remove it for ner detail spraying.

TROUBLESHOOTING:

Bubbling in cup:

1. VLH Head #3 needs to be wrench tightened

Skipping or spitting:

1. Paint too thick -Reduce with thinner

2. Tip not seated -Tighten VLH Head with wrench

3. Tip split or damaged needle -Replace tip or needle

4. Needle or tip dirty -Clean and replace

5. Air pressure too low -Increase pressure or thin paint further (need 20 or more PSI to spray most paints)

Airbrush not spraying:

1. Clogged tip -Remove tip and clean

2. Needle not retracted -Adjust back knob

3. Loose VLH Head -Wrench tighten

4. Low air pressure -Increase pressure (need 20 or more PSI to spray most paints)

5. Bottle vent hole plugged -Use needle or pin to clear air hole

Sprays double line or heavy to one side:

1. Split tip or bent needle - Replace

2. Dirty tip or needle - Remove and clean

3. Tip not centered in head - Remove head and clean airbrush seat and tip seat then reassemble. Use wrench for head

INSTRUCTIONS AND PARTS LIST SI-8/06/2019

SI – Airbrush

Double Action - Internal Mix

Siphon Feed

Paasche® model SI features hand crafted

construction using quality materials. The body

is machined brass, polished and chrome plated.

Fluid tips are nickel silver, needles are stainless

steel & the needle packing is PTFE. Preferred

by professional and hobbyist alike.

Paasche Airbrush Co. 9511 58th Place Kenosha, WI. 53144 Phone:773/867-9191 Email: info @ paascheairbrush.com

Produkt Specifikationer

Mærke:	Paasche
Kategori:	Ikke kategoriseret
Model:	2000SI

Har du brug for hjælp?

Hvis du har brug for hjælp til Paasche 2000SI stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Paasche Manualer

Paasche 2000SI Manual

22 August 2024

Paasche VL-1AS Manual

22 August 2024

Paasche TS-3AS Manual

22 August 2024

Paasche D220R Manual

22 August 2024

Paasche VL-100D Manual

22 August 2024

Paasche RG-3AS Manual

22 August 2024

Paasche TG-1AS Manual

22 August 2024

Paasche H-100D Manual

22 August 2024

Paasche FP-1/32 Manual

22 August 2024

Paasche H-3AS Manual

22 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Siemens WQ32G28IL Manual

6 December 2025

MDT BE-TA550606.02 Manual

6 December 2025

Opticis USC-CC32 Manual

6 December 2025

Audio-Technica AT33xMONO Manual

6 December 2025

Bosch SPI4EMS24E Manual

6 December 2025

Fostex P1000K Manual

6 December 2025

Advantech UTC-124I1 Manual

6 December 2025

Anton/Bauer Titon Micro Kit Manual

6 December 2025

Philips Zoom! DayWhite DIS130 Manual

6 December 2025

Opticis USB-FC30AA Manual

6 December 2025