Paasche FP-1/32 Manual

Paasche Ikke kategoriseret FP-1/32

Læs gratis den danske manual til Paasche FP-1/32 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 18 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 9.5 anmeldelser. Har du et spørgsmål om Paasche FP-1/32, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

FP-1/32

Flow Pencil

OPERATING INSTRUCTIONS & REPLACEMENT

PARTS

INSTRUCTION AND PARTS LIST FP-1/32 1/5/2018

Paasche Airbrush Co.

9511 58th Place

Kenosha, WI 53144

Phone: (800) 621-1907

Website: www.paascheairbrush.com

E-Mail: info@paascheairbrush.com

Comes with LN-1/32 (Assembled) and LN-1/64, 3/64, and 1/16 Nibs loose

Total Length of Flow Pencil is 5 -1/2 inches.

HAPK Kit comes with one size nib only

Printed in the U.S.A.

INTRODUCTION:

The FP-1/32 Flow Pencil is used extensively by Designers,

Sculptors, Hobbyists, Crafters, Ceramicists, Artists, Furniture

Manufacturers, and others to beautify their products. The Flow

Pencil is easy to control and operate.

MIXING COLORS:

1. Proper mixing of colors is essential for continuous and

uninterrupted striping.

2. Mix colors into a free flowing consistency, strain to remove

any lumps.

3. Do not mix color in cup of Flow Pencil, use a separate

container and pour into cup only when color flows freely.

COLOR ADJUSTMENTS:

1. Remove FP-10 Cover, and pour premixed free flowing color

into cup, then replace cover.

2. Turning the MU-72 Adjusting Screw will control the stroke

of the which controls theMU-65 Finger Lever Assembly

flow of color.

OPERATION:

1. Hold the FP-1/32 Flow Pencil in your hand as you would a

pencil or brush and place your finger lightly over the MU-65

Finger Lever. When ready to stripe, pull back on the

MU-65 Finger Lever. The Flow Pencil should be moved in

a backward motion (away from the paint) after the color has

begun to flow, never push it into the paint.

2. Regulate the flow to the desired feed rate by turning MU-72

Adjusting Screw.

3. Keep vent hole in the open.FP-10 Cover

4. Practice striping before working on finished product.

5. Correct adjustment of controls and skill of operation will

result in uninterrupted and continuous striping.

CARE AND CLEANING:

1. Before storing FP-1/32 Flow Pencil clean it thoroughly. Empty

remaining color from the cup and rinse it with solvent. Pull back

on the MU-65 Finger Lever and allow solvent to flow through

cup, shell and nib.

2. If color has hardened in hole of nib use a tooth pick or needle

dipped in solvent to remove accumulation.

3. MU-49L Needle is held in position by MU-57 Needle Chuck

and VL-141 Locknut. Remove the needle by unscrewing the

MU-71 Handle and removing the spring. Loosen the VL-141

Locknut and then remove the needle for cleaning.

ADJUSTING OR REPLACING WORN PACKING WASHER:

1. If PTFE Packing-#6 becomes worn or loose it must be

tightened or replaced.

2. You will need a small screwdriver to remove or tighten the

Packing Nut.

3. When replacing your PTFE Packing press Packing onto the

Packing Nut-#6. Use a small screwdriver to tighten packing nut

into shell until it is tight then back out one-half turn, may vary.

4. Now insert needle - you should feel a slight resistance. If too

loose or too tight adjust the Packing Nut with screwdriver until

you feel some slight resistance.

5. Now completely re-assemble guts of Flow Pencil.

WARNING: Striping materials may be harmful if inhaled or

allowed to come into contact with the skin or eyes. Consult

the product label and Material Safety Data Sheet supplied for

the spray material. Follow all safety precautions. CAUTION:

Well Ventilated Area Required to remove fumes.

CAUTION: OVER TIGHTENING CUP WILL

CAUSE TRIGGER TO MALFUNCTION.

Page 2 FP-1/32 Flow Pencil Parts List

No. Part No. Description

3. Tip Nut *MU-9

4. Nib (1/64, 3/64 & 1/16 Sizes)**LN-1/32

5. Shell Assembly*MU-48A

6. **MU-612 PTFE Packing & Packing Nut

8. Finger Lever Assembly**MU-65

10. Basic Cover (only) *FP-10

11. MU-71 Handle

12. 3A-4 “O” Ring

13. **MU-72 Adjusting Screw

14. **MU-57 Needle Chuck

15.***MU-49L Needle

16. **VL-141 Locknut

18.***VL-140 Spring

No. Part No. Description

31. Cup (only) Aluminum *FP-6

32. StandMU-77

33. “O” RingAE-43

(OPTIONAL PRESSURE CUP)

24. (Complete assembly)FP-45

25. Rod & Cap Assembly**MU-25

26. Nut*MU-69

27. Pressure Cover (only)*FP-5

28. SpringMU-26

29. Piston*FP-9

30. (FDA) “O” Ring****FP-8

31. Cup (only) Aluminum*FP-6

33. “O” Ring (rubber)AE-43

FP-1/32 FLOW PENCIL (WITH EXTRA NIBS: LN-1/64, 3/64 AND 1/16)

HAPK KIT comes with one size nib only

Nibs are grooved as follows:

LN-1/64 has one (1) groove

LN-1/32 has two (2) grooves

LN-3/64 has three (3) grooves

LN-1/16 has four (4) grooves

Contains Aluminum....*

Contains Brass....**

Contains Stainless Steel....***

Contains FDA Approved Silicone....****

Produkt Specifikationer

Mærke:	Paasche
Kategori:	Ikke kategoriseret
Model:	FP-1/32

Har du brug for hjælp?

Hvis du har brug for hjælp til Paasche FP-1/32 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Paasche Manualer

Paasche 2000SI Manual

22 August 2024

Paasche VL-1AS Manual

22 August 2024

Paasche TS-3AS Manual

22 August 2024

Paasche D220R Manual

22 August 2024

Paasche VL-100D Manual

22 August 2024

Paasche RG-3AS Manual

22 August 2024

Paasche TG-1AS Manual

22 August 2024

Paasche H-100D Manual

22 August 2024

Paasche FP-1/32 Manual

22 August 2024

Paasche H-3AS Manual

22 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Joy-It SEN-DHT22 Manual

9 Oktober 2025

Axxess AXBUCH-T1 Manual

9 Oktober 2025

Lofrans THETIS 1002 Manual

9 Oktober 2025

Crown IC-150A Manual

9 Oktober 2025

ACTi INR-415 Manual

9 Oktober 2025

Pioneer ND-BC011 Manual

9 Oktober 2025

Axxess AXSSO-CH Manual

9 Oktober 2025

Caliber MPD 297 Manual

8 Oktober 2025

ENTES ENT.CXD.H-450-12,5 Manual

8 Oktober 2025

Vollrath LP55278 Manual

8 Oktober 2025