Paasche RG-1AS Manual

Paasche Ikke kategoriseret RG-1AS

Læs gratis den danske manual til Paasche RG-1AS (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 10 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 5.5 anmeldelser. Har du et spørgsmål om Paasche RG-1AS, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

INSTRUCTIONS & PARTS LIST RAPTOR- 9-25-2020

RAPTOR

RAPTORRAPTOR

Double A c t i on- I n t er nal M ix- G r avi t y Feed-

PTFE Packings.

Si z e Needle, T i p , and Ai r c a p Inst al l ed# 1 .

WARNING: Spray materials may be harmful if inhaled or allow

to come into contact with the skin or eyes. Consult the product

label and Material Safety Data Sheet supplied for the spray

material. Follow all safety precautions. CAUTION: Well Ventilated

Area Required to remove fumes, dust or overspray. Secure airhose

to Airbrush with V-62 Wrench for safety and to prevent air leaks.

M P S a x A i u m m i r r s e s u . r 7 e 5 P . I .

*Note: Etch on Items lines

2 3 2 . and 1 size. All should indicate

match when on airbrush.installed

For Multi-Language Manuals go to: www.paascheairbrush.com

1. Attach to to air hose air supply and airbrush. 20-55 If using pressure a regulator set between psi .

2. Press down on Finger Button to air and pull back on button to control quantity of color.release

3. Speed of movement controls color density of and end fading effects at beginning and of strokes.

4. Practice this movement until you can spray a fine line or a broad pattern without heavy build up at the beginning or end of your

strokes.

5. For detail, the very to the hold airbrush close surface push down for air and pull back very slowly on the Finger Button to release a

small amount of paint.

6. For background work and away broad hold effects, the airbrush from the work surface and pull back on Finger Button to release

required amount of color.

• Dual Action • Gravity Feed • Internal M x • Cutaway Handle w/ Pre-set Needle Stop •i • 1/10th gravity cup ounce PTFE Packing

•TT-1 , and TN-1, TA-1 components come the Installed on Raptor.

Options for :Raptor

.2mm head (TT- TN- TA-1 fine detail0, 0 and components) Great for jobs requiring the "extremely "

.25mm head (TT-1, TN-1, and TA-1 component

.38mm head (TT-2, TN-2 and TA-2 ) components

.66mm head and TA-3 ) Great for spraying Metallics, Pearlescent and Thicker Paints(T -3 T ,TN-3 components .

Working Pressures:

Operating pressures 15-55 PSI; Maximum pressure 85 PSI. aircap needs 20 PSI more.Fan or

20-30 PSI best for detail spraying w/ properly paintis thinned .

Use the is not higher pressures detail for thicker material where fine critical or thin the paint for lower pressures.

RG Specifications:

NO. PART

1. XI-41

2. *TA-1, TA-2, TA-3* *

3. 0 1*TT- , TT-*, TT-2, TT-3* *

4. MIL-12

5. RG-30

6. RG-8

7. TAL-8

8. TAL-37

9. TAL-14

10. TAL-36

11. A-22

12. TAL-26

13. TAL-15

14. TAL-18

15. MIL-11

16. TAL-17

17. TAL-19

18. MIL-12

19. RG-20

20. TAL-33

21. *TN-1

22. TAL-35

23. TAL-28

24. 3A-4

DESCRIPTION

Needle Protection Cap

Head (.25mm, .38mm, .66mm)

(Size TA-1 is used size 0 1 Tip)Head with and

Tip (.2mm, .25mm, .38mm, .66mm)

"O" Ring

Shell

Cup Cover

Packing assembly PTFE

Trigger

Air Valve Casing

Air Valve Plunger

Air Valve Spring

"O" Ring

Air Valve Adapter

Rocker Assembly

Needle Spring

Spring Housing

Needle Locknut

"O" Ring

Handle

Needle Stop

Needle (.25mm)

Allen Wrench

Wrench

"O" Ring

Airbrush Operation:

)

NO. PART DESCRIPTION

Page 2

Paasche® Gravity Feed, Double Action AirbrushRG

Phone: (800)621-1907 Website: E-Mail: paascheairbrush.com info@paascheairbrush.com

REMOVING / REPLAClNG THE NEEDLE AND HANDLE:

1. Unscrew the handle and loosen the Locknut- #TAL-19 by turning counterclockwise. Depress the

Trigger- #TAL-37 and hold in down position while removing or inserting the needle. This assures the

needle moves freely through the trigger. Gently remove the needle, rotating if necessary.

2. Inspect the condition of the needle. If it is bent or misshapen in any way, replace it with a new needle.

A bent needle can damage or split the Tip- #TT causing bubbles or a rough spray pattern.

3. Hold trigger in down position, insert the new needle into the Rocker Assembly- #TAL-18. Gently push

needle forward until the needle stops in the front of the tip.

4. Release trigger and tighten locknut by turning clockwise.

REPLACING THE FINGER LEVER ASSEMBLY:

If the Trigger- #TAL-37 is removed, it is easiest to replace before the Rocker Assembly- #TAL-18 is

inserted. The needle must be removed.

1. Hold trigger so the round side of the stem is to the front and at side to the back of the airbrush

2. Insert trigger straight DOWN through the opening in the top of the airbrush shell.

3. You want the bottom of the trigger to cover the round ball on top of the exposed plunger. Once the

connection is made you should have spring action when pushing down on the trigger. Proceed to

replace Rocker Assembly- #TAL-18 and balance of parts as above. When the needle is inserted it

will prevent the removal of the trigger.

REPLACING THE TIP:

1. Remove handle, loosen Locknut- #TAL-19 and withdraw needle about one inch (1”).

2. Un-screw the Aircap- #TA and remove. The Tip- #TT can now be unscrewed with Wrench- #TAL-28.

3. Replace tip and tighten with wrench. The tip must be wrench tight. Push needle forward and lock.

ADJUSTING WORN PACKING WASHER:

1. If Packing Assembly- #TAL-8 becomes worn or loose it must be tightened or replaced.

2. Tighten packing nut with small screwdriver. To reach packing all internal parts must be removed.

3. Replace needle and make sure packing nut is not too tight. Slight resistance is needed when needle

passes through.

CLEANING THE AIRBRUSH:

1. Spray airbrush cleaner through airbrush until it has no more color spraying out of airbrush.

2. Remove needle and wipe clean then replace.

3. If paint has dried for a time you can remove the front tip, and aircap for soaking or soak just the front of the

airbrush in cleaner.

4. Any paint cleaner is ne. Keep trigger area dry if soaking.

PERSONAL SETTINGS:

Spring Housing- #TAL-17 Used to increase or decrease spring tension for the trigger pull back. Thread

into the shell until the trigger stroke feels comfortable. Threading in until it stops can cause the trigger

to jam.

TROUBLESHOOTING:

Bubbling in cup:

1. Aircap- #TA needs to be tightened

2. Tip- #TT needs to be tightened further

Skipping or Spitting:

1. Paint too thick -reduce with thinner

2. Tip not seated -tighten Tip- #TT with wrench

3. Tip split or damaged needle -replace tip or needle

4. Needle or tip dirty -clean and replace

5. Air pressure too low -increase pressure or thin paint further (need 20 or more PSI to spray most

paints)

Airbrush Not Spraying:

1. Clogged Tip- #TT -remove tip and clean

2. Needle not moving -tighten needle locknut

3. Low air pressure -increase pressure (need 20 or more PSI to spray most paint)

Sprays double line or heavy to one side:

1. Split Tip- #TT or bent Needle- #TN - replace

2. Dirty tip or needle - remove and clean

Jammed trigger or poor trigger motion:

1. Adjust #TAL-17 screw or unscrew Spring Housing- - the spring housing to lessen or increase tension on

trigger motion

2. Paint leaking to trigger - remove guts of airbrush tighten packing or replace if neededarea and slightly

3. Lubricate needle and trigger - apply Paasche Airbrush Lube (AL-2) to needle shaft and trigger slot area.

Printed in the U.S.A.

Produkt Specifikationer

Mærke:	Paasche
Kategori:	Ikke kategoriseret
Model:	RG-1AS

Har du brug for hjælp?

Hvis du har brug for hjælp til Paasche RG-1AS stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Paasche Manualer

Paasche 2000SI Manual

22 August 2024

Paasche VL-1AS Manual

22 August 2024

Paasche TS-3AS Manual

22 August 2024

Paasche D220R Manual

22 August 2024

Paasche VL-100D Manual

22 August 2024

Paasche RG-3AS Manual

22 August 2024

Paasche TG-1AS Manual

22 August 2024

Paasche H-100D Manual

22 August 2024

Paasche FP-1/32 Manual

22 August 2024

Paasche H-3AS Manual

22 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Hozelock 5102 Manual

2 August 2025

ART 310 Manual

2 August 2025

Gorenje KAS53ZDCINVFT Manual

2 August 2025

Gorenje KAS35ZDCINVFT Manual

2 August 2025

Navman MY450LMT Manual

2 August 2025

Navman MiVue 745 Manual

1 August 2025

Hitachi WR22SE Manual

1 August 2025

Synology M2D20 Manual

1 August 2025

Fluke FibertLert-125 Manual

1 August 2025

Buffalo GC882 Manual

1 August 2025