Paasche TG-3AS Manual

Paasche Ikke kategoriseret TG-3AS

Læs gratis den danske manual til Paasche TG-3AS (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 13 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 7 anmeldelser. Har du et spørgsmål om Paasche TG-3AS, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

INSTRUCTIONS AND PARTS LIST TG-TALON

TG TALON – Airbrush

Double Action - Internal Mix - Gravity Feed -

PTFE Packings.

WARNING: Spray materials may be harmful if

inhaled or allowed to come into contact with the

skin or eyes. Consult the product label and material

safety data sheet supplied for the spray material.

Follow all safety precautions. Well CAUTION:

Ventilated Area Required to remove fumes, dust or

overspray. Maximum Air Pressure 75 P.S.I.

TG Specications:

• Dual Action • Gravity Feed • Internal Mix • Cutaway Handle w/ Pre-set Needle Stop • PTFE Packing

TT-2, TN-2, and TA-2 Components come installed on Talon.

Options for Talon:

.2mm head (TT-0, TN-0, TA-0 components) - Great for jobs requiring “extremely ne detail”.

.25mm head (TT-1, TN-1 and TA-1 components) - Great for jobs requiring ne detail

.66mm head (TT-3, TN-3 and TA-3 components) - Great for spraying Metallics, Pearlescent and Thicker

Paints

.66mm Fan Aircap (TAF-3, TN-3 and TT-3) Will give a 2-1/2 to 3 inch fan pattern.

Working Pressures:

• Operating pressures 15-55 PSI; Maximum pressure 85 PSI. Fan aircap needs 20 PSI or more.

• 20-30 PSI is best for detail spraying w/ properly thinned paint

• Use the higher pressures for thicker material where ne detail is not critical or, thin the paint to allow

lower pressures.

Equipment Set-up:

The Airbrush is held in the same manner as a pen, with index nger comfortably over the nger button.

1. Attach air hose to air supply and to airbrush. If using a regulator set pressure between 20 -55 PSI.

Airbrush Operation:

1.Attach air hose to air supply and to airbrush.If using a regulator set pressure between20-55psi.

2.Press down on Finger Trigger to release air and pull back on trigger to control quantity of color.

3.Speed of movement controls density of color and fading e󰀨ects at beginning and end of strokes.

4.Practice this movement until you can spray a ne line or a broad pattern without heavy build up at the

beginning or end of your strokes.

5.For detail, hold the airbrush very close to the surface push down for air and pull back very slowly on

the Finger trigger to release a small amount of paint.

6. For background work and broad e󰀨ects, hold the airbrush away from the work surface and pull back

on Finger trigger to release required amount of color.

NO. PART DESCRIPTION

1. XI-41 Crown Cap

1a. TAF-3 Fan Aircap for .66mm head -

2. TA-1 TA-2 TA-3, , Aircap (.25mm, .38mm, .66mm)

(Size TA-1 head is used with size 0 and 1 tip)

3. TT-0,TT-1 TT-2 TT-3, , Tip(.2mm,.25mm,.38mm,.66mm)

4. MIL-12 “O” Ring for TG-30 Shell

5. TG-30 Shell Assembly

6. TG-4 Cup Cover

7. Packing Assembly PTFETAL-8

8. TAL-37 Trigger

9. TAL-14 Valve Casing

10. TAL-36 Valve Plunger (Includes O-ring)

10a. Optional) Pack of (6) O-ringsA-53 (

11. TAL-15 Valve Adapter (Includes O-ring)

11a. TAL-22 (Optional) Pack of (6) O-rings

12. A-22 Spring

17. TAL-18 Rocker Assembly

18. MIL-11 Needle Spring

19. TAL-17 Spring Housing

20. TAL-19 Needle Lock Nut

21. MIL-12 “O” Ring for TG-34 Handle

22. TAL-20 Handle

23. 3A-4 “O” Ring

24.TN-0 TN-1, ,TN-2, TN-3 Needle

(.2mm .25mm .38mm .66mm)

25. TAL-35 Allen Wrench

26. TAL-28 Wrench

27. Needle StopTAL-33

*Note: Etch lines on Items

2 3 and 2 . indicate size. 4

All should match when

installed on airbrush.

Printed in the USA

REMOVING / REPLAClNG THE NEEDLE AND HANDLE:

1. Unscrew the handle and loosen the Locknut- #TAL-19 by turning counterclockwise. Depress the

Trigger- #TAL-37 and hold in down position while removing or inserting the needle. This assures the

needle moves freely through the trigger. Gently remove the needle, rotating if necessary.

2. Inspect the condition of the needle. If it is bent or misshapen in any way, replace it with a new needle.

A bent needle can damage or split the Tip- #TT causing bubbles or a rough spray pattern.

3. Hold trigger in down position, insert the new needle into the Rocker Assembly- #TAL-18. Gently push

needle forward until the needle stops in the front of the tip.

4. Release trigger and tighten locknut by turning clockwise.

REPLACING THE FINGER LEVER ASSEMBLY:

If the Trigger- #TAL-37 is removed, it is easiest to replace before the Rocker Assembly- #TAL-18 is

inserted. The needle must be removed.

1. Hold trigger so the round side of the stem is to the front and at side to the back of the airbrush

2. Insert trigger straight DOWN through the opening in the top of the airbrush shell.

3. You want the bottom of the trigger to cover the round ball on top of the exposed plunger. Once the

connection is made you should have spring action when pushing down on the trigger. Proceed to

replace Rocker Assembly- #TAL-18 and balance of parts as above. When the needle is inserted it

will prevent the removal of the trigger.

REPLACING THE TIP:

1. Remove handle, loosen Locknut- #TAL-19 and withdraw needle about one inch (1”).

2. Un-screw the Aircap- #TA and remove. The Tip- #TT can now be unscrewed with Wrench- #TAL-28.

3. Replace tip and tighten with wrench. The tip must be wrench tight. Push needle forward and lock.

ADJUSTING WORN PACKING WASHER:

1. If Packing Assembly- #TAL-8 becomes worn or loose it must be tightened or replaced.

2. Tighten packing nut with small screwdriver. To reach packing all internal parts must be removed.

3. Replace needle and make sure packing nut is not too tight. Slight resistance is needed when needle

passes through.

CLEANING THE AIRBRUSH:

1. Spray airbrush cleaner through airbrush until it has no more color spraying out of airbrush.

2. Remove needle and wipe clean then replace.

3. If paint has dried for a time you can remove the front tip, and aircap for soaking or soak just the front of the

airbrush in cleaner.

4. Any paint cleaner is ne. Keep trigger area dry if soaking.

PERSONAL SETTINGS:

Spring Housing- #TAL-17 Used to increase or decrease spring tension for the trigger pull back. Thread

into the shell until the trigger stroke feels comfortable. Threading in until it stops can cause the trigger

to jam.

TROUBLESHOOTING:

Bubbling in cup:

1. Aircap- #TA needs to be tightened

2. Tip- #TT needs to be tightened further

Skipping or Spitting:

1. Paint too thick -reduce with thinner

2. Tip not seated -tighten Tip- #TT with wrench

3. Tip split or damaged needle -replace tip or needle

4. Needle or tip dirty -clean and replace

5. Air pressure too low -increase pressure or thin paint further (need 20 or more PSI to spray most

paints)

Airbrush Not Spraying:

1. Clogged Tip- #TT -remove tip and clean

2. Needle not moving -tighten needle locknut

3. Low air pressure -increase pressure (need 20 or more PSI to spray most paint)

Sprays double line or heavy to one side:

1. Split Tip- #TT or bent Needle- #TN - replace

2. Dirty tip or needle - remove and clean

Jammed trigger or poor trigger motion:

1. Adjust Spring Housing- #TAL-17 - screw or unscrew the spring housing to lessen or increase tension

on trigger motion

2. Paint leaking to trigger area - remove guts of airbrush and slightly tighten packing or replace if needed

3. Lubricate needle and trigger - apply Paasche Airbrush Lube (AL-2) to needle shaft and trigger slot

area.

Paasche Airbrush Co. 9511 58th Place Kenosha, WI. 53144 Phone:773/867-9191

Email:info@paascheairbrush.com

For Multi-Language Manuals Go To: www.paascheairbrush.com

Produkt Specifikationer

Mærke:	Paasche
Kategori:	Ikke kategoriseret
Model:	TG-3AS

Har du brug for hjælp?

Hvis du har brug for hjælp til Paasche TG-3AS stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Paasche Manualer

Paasche 2000SI Manual

22 August 2024

Paasche VL-1AS Manual

22 August 2024

Paasche TS-3AS Manual

22 August 2024

Paasche D220R Manual

22 August 2024

Paasche VL-100D Manual

22 August 2024

Paasche RG-3AS Manual

22 August 2024

Paasche TG-1AS Manual

22 August 2024

Paasche H-100D Manual

22 August 2024

Paasche FP-1/32 Manual

22 August 2024

Paasche H-3AS Manual

22 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Slingshot SL (2025) Manual

13 August 2025

Crestron CLTIBN-1DIM4 Manual

13 August 2025

Beverage-Air PH2-1BG-PT Manual

13 August 2025

Swann SWIFI-MPRSB1T1 Manual

13 August 2025

Slingshot R (2024) Manual

13 August 2025

Heinner MG-2100SS Manual

13 August 2025

Advantech BB-SR30918320-SWH Manual

13 August 2025

Camry CR 3061 Manual

13 August 2025

Crestron FT2A-CBLR-GR-USB Manual

13 August 2025

Advantech PCI-1716-BE Manual

13 August 2025