PAC RadioPRO 4 RP4.2-HY12 Manual

PAC Radio RadioPRO 4 RP4.2-HY12

Læs gratis den danske manual til PAC RadioPRO 4 RP4.2-HY12 (7 sider) i kategorien Radio. Denne vejledning er vurderet som hjælpsom af 22 personer og har en gennemsnitlig bedømmelse på 3.7 stjerner ud af 11.5 anmeldelser. Har du et spørgsmål om PAC RadioPRO 4 RP4.2-HY12, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/7
Pacic Accessory Corporation
® | Ph. 866-931-8021 | support@pac-audio.com
©2015 Pacic Accessory Corporation
www.pac-audio.com
P ifi A C ti
RP4.2-HY12
Radio Replacement &
Steering Wheel Control Interface
for Hyundai Veloster
Rev. 101515
Page 1
Introduction & Features
Important Notes
The RP4.2-HY12 interface allows the replacement of a factory radio in the Hyundai Veloster. Using this interface will
retain factory features such as: steering wheel controls (SWC), secondary screens, reverse camera and factory SPDIF
audio amplier (seperate part required, part # RPA-SPDIF) whenever the original radio is removed. Use of this interface
also allows you to program two radio functions to each SWC button by using short press long press dual command
functionality. The RP4.2-HY12 also provides data bus driven outputs such as vehicle speed sense (VSS), illumination,
reverse trigger and parking brake.
1. Does not retain Blue Link. You must use the RP5.2-HY12 to retain Blue Link.
2. The AUX connection in the RP4 harness will only provide sound if the aftermarket radio has a USB port. This is because the
USB port provides the power to make the factory USB/AUX port work. If you have connected the USB plug to your aftermarket
radio and it is still inoperable, this means that the aftermarket radio’s USB port is not supplying enough current.
3. When using the RPA-SPDIF in factory amplied vehicles, you can adjust factory amplier settings such as Bass, Mid, Treble,
Fader, Balance and Gain with the RadioPRO app found at www.pac-audio.com. Please refer to page 6 for detailed instructions
on the app and the functionality of this wire.
4. In vehicles equipped with auto climate controls, you will lose the fan mode, fan speed, auto status and temperature display.
Wiring Connection Chart
3.5mm Jack SWC Output
Pink MS-CAN + Input
Pink/Black MS-CAN - Input
Blue/Yellow SWC Output
Red/White 12v+ Programmable
Output (1 amp)
Orange/White Illumination Output
Pink Vehicle Speed
Sense Output
Violet/White Reverse Output
White/Black HS-CAN + Input
White/Red HS-CAN - Input
White Analog SWC
Orange/Black Illumination Input
Light Green Parking Brake
Output (-)
Blue/White Amp Turn On Input
Interface Connector 2
Yellow Battery +12v
Black Ground
Blue Power Antenna
Turn On Input
White Front L + input
White / Black Front L - input
Grey Front R + input
Grey / Black Front R - input
Green Rear L + input
Green / Black Rear L - input
Purple Rear R + input
Purple / Black Rear R - input
Yellow RCA Factory Reverse
Camera Video (if
equipped)
Vehicle ConnectorInterface Connector 1
Red Accessory Output
(10 amp)
Yellow 12v+
Black Ground
Red Accessory Output
Pacic Accessory Corporation
® | Ph. 866-931-8021 | support@pac-audio.com
©2015 Pacic Accessory Corporation
www.pac-audio.com
P ifi A C ti
RP4.2-HY12
Radio Replacement &
Steering Wheel Control Interface
for Hyundai Veloster
Rev. 101515
Page 2
Default Steering Wheel Control Programming
IMPORTANT! The interface comes pre-programmed for all of the vehicles factory SWC functions and does not require
programming unless you wish to re-assign the SWC functions, utilize short press long press dual command functionality or assign
the programmable 12v output to a SWC button. The SWC can always be restored to default settings by pressing and releasing
the program button on the side of the interface once and waiting 7 seconds for the LED to ash 3 times.
Installation Steps
1. The radio select dipswitches on the side of the interface must be adjusted to the proper radio
setting before plugging the interface into the vehicle.
2. Make all connections as described in the connection chart on page 1. Vehicles without a factory amplier: Connect the
aftermarket radio’s front and rear speaker wires to the vehicle connector. Vehicles with a factory amplier: Connect the
aftermarket radio’s front speaker wires to the SPDIF converter (sold seperately, part # RPA-SPDIF), then connect the SPDIF
converter to the 6-pin connector located on the RP4.2 harness.
3. Connect the SWC wire to the aftermarket radio (aftermarket radio must support a wired remote input).
4. Once all connections have been made, plug the interface into the vehicle.
5. If you wish to reassign functions to the SWC, utilize short press long press dual command functionality or assign the
programmable 12v output to a SWC button, follow the optional programming instructions on the next page.
Module Layout
Module Status LED
Programmable
Output/USB Status
LED
Interface Connector 1
Expansion
Port
Interface Connector 2
Programming
Button
USB Port
Radio Select Dipswitches
Steering Wheel Controls
DIP
1234
ON
Alpine JVC Kenwood Clarion Pioneer/Other Sony Fusion
1 2 1 & 2 3 1, 2, & 3 4 1 & 4
SET RADIO DIPSWITCHES TO THE ON POSITION

Produkt Specifikationer

Mærke: PAC
Kategori: Radio
Model: RadioPRO 4 RP4.2-HY12

Har du brug for hjælp?

Hvis du har brug for hjælp til PAC RadioPRO 4 RP4.2-HY12 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Radio PAC Manualer

PAC

PAC RPA-SPDIF Manual

9 August 2024
PAC

PAC RadioPRO 4 RP4.2-HY12 Manual

8 August 2024

Radio Manualer

Nyeste Radio Manualer

ECG

ECG CDR 990 Manual

30 Juli 2025
Blaupunkt

Blaupunkt BR-90DABi Manual

28 Juli 2025
TechniSat

TechniSat DIGITRADIO 10 Manual

28 Juli 2025
JVC

JVC RA-E313B-DAB Manual

27 Juli 2025
Uniden

Uniden BearTracker 885 Manual

27 Juli 2025
TechniSat

TechniSat DigitRadio 574 IR Manual

27 Juli 2025
TechniSat

TechniSat Classic 200 Manual

27 Juli 2025
Lenco

Lenco PDR-016 Manual

26 Juli 2025
Lenco

Lenco DIR-270 Manual

25 Juli 2025
Lenco

Lenco MPR-035 Manual

25 Juli 2025