PAC RPA-SPDIF Manual

PAC Radio RPA-SPDIF

Læs gratis den danske manual til PAC RPA-SPDIF (1 sider) i kategorien Radio. Denne vejledning er vurderet som hjælpsom af 16 personer og har en gennemsnitlig bedømmelse på 4.1 stjerner ud af 8.5 anmeldelser. Har du et spørgsmål om PAC RPA-SPDIF, eller vil du spørge andre brugere om produktet?

Side 1/1

RPA-SPDIF

Amplier Retention Module

For use with PAC RadioPRO Interfaces

Pacic Accessory Corporation

® | Ph. 866-931-8021 | support@pac-audio.com

©2015 Pacic Accessory Corporation

www.pac-audio.com

Rev. 082615

P ifi A C ti

The RPA-SPDIF is an analog to SPDIF converter designed for use with select RadioPRO interfaces. This

module will convert analog audio from an aftermarket radio to the SPDIF signal used by some factory

ampliers.

Introduction & Features

Module Overview

1. Connect the 10-pin harness to the RPA-SPDIF.

2. Connect the speaker inputs of the RPA-SPDIF harness.

a. When using with an RP5.2 module, simply plug the 12-pin connector into the

amplied audio output of the interface.

b. When using with an RP4.2 module, you will need to cut off the 12-pin connector

and wire the right and left speaker inputs to the front speaker outputs of the

aftermarket radio.

3. Connect the 6-pin plug on the RPA-SPDIF (Fig 1) harness to the 6-pin plug on the

RadioPRO harness (Fig 2).

4. Turn the Gain Adjustment dial on the RPA-SPDIF all the way to the left (counter

clockwise).

5. Turn on the aftermarket radio and set the volume to about 2/3 max volume.

6. Begin turning the Gain Adjustment knob on the RPA-SPDIF to the right (clockwise).

Do this until the red clipping LED begins ashing.

7. Once the red LED has turned on, turn the Gain Adjustment knob on the RPA-SPDIF

slightly to the left (counter clockwise) until the red LED goes off.

8. Turn off the aftermarket radio and secure the RPA-SPDIF to the RadioPRO harness.

Installation of the RPA-SPDIF is now complete.

Installation Steps

Wiring Harness

Power LED

Clipping LED

Gain Adjustment

Fig 1

Fig 2

Produkt Specifikationer

Mærke:	PAC
Kategori:	Radio
Model:	RPA-SPDIF

Har du brug for hjælp?

Hvis du har brug for hjælp til PAC RPA-SPDIF stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Radio PAC Manualer

PAC RPA-SPDIF Manual

9 August 2024

PAC RadioPRO 4 RP4.2-HY12 Manual

8 August 2024

Radio Manualer

Nyeste Radio Manualer

Aiwa RD-10 Manual

30 Oktober 2025

Pinell Supersound 901 Manual

16 Oktober 2025

Ruark Audio MR1 Manual

12 Oktober 2025

Ruark Audio R3 Manual

12 Oktober 2025

Ruark Audio R2 Mk4 Manual

12 Oktober 2025

Ruark Audio R810 Manual

12 Oktober 2025

Ruark Audio R2 Mk3 Manual

12 Oktober 2025

TechniSat Viola CD-1 Manual

10 Oktober 2025

Blow RA6 Manual

9 Oktober 2025

Caliber HBC 426BT Manual

8 Oktober 2025