PAC VS41 Manual

PAC Skifte VS41

Læs gratis den danske manual til PAC VS41 (22 sider) i kategorien Skifte. Denne vejledning er vurderet som hjælpsom af 52 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 26.5 anmeldelser. Har du et spørgsmål om PAC VS41, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/22
© 2018 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global.
PAC-audio.com
P ifi A C ti
Rev. 032018
Intelligent 4 Camera Switcher for Controlling
Front, Rear, and Blind Spot Cameras
VS41
The VS41 is an intelligent 4 camera switcher for controlling front, rear, and blind spot cameras. Manually connect
cameras and trigger wires (pulsed or constant inputs), or connect to a BCI-, RP4.2-, or RPA- module's expansion port
for full digital control, and fast easy connectivity. The VS41 also accepts analog + or - and constant / pulsed signals.
Introduction & Features
Important Notes
1. If you are using the VS41 with another PAC interface, such as a BCI-, RP4.2-, or RPA-, with an Expansion Port, simply
connect the 10-pin connector into the module. Do not manually wire the positive or negative trigger wires. The BCI-,
RP4.2-, or RPA- module will digitally control the VS41 switching operation when connected to the Expansion Port.
2. The VS41 video output will always default to the signal from Input 1 when none of the input triggers are activated. This
Input is ideal for connecting the rear (reverse) camera.
3. The VS41 inputs have priority in descending numerical order. For example: If you have Input 3 or 4 triggered, then you
trigger a lower number input (for example Input 2), Input 2 will take priority over the higher numbered Input.
4. The input triggers can accept either a pulsed or constant input, making them ideal for connecting to a turn signal as a
trigger.
5. The reverse trigger output will provide a 150 mA 12v (+) trigger while any of the input triggers are activated.
6. Upon deactivation of the last positive or negative trigger, the last video input source and the reverse trigger output will
remain active for an additional 3 seconds. (Not applicable when used with a BCI-, RP4.2-, or RPA- interface).
7. If there is poor video quality after installation of this module, please ensure quality connections on any RCA connections.
8. Positive Input triggers accept input voltages in the range of 2v to 12v.
Video Output
Video 1 Input - Reverse Camera
Video 2 Input - Front Camera
Video 3 Input - Left Blind Spot
Video 4 Input - Right Blind Spot
Input 1 trigger (+)White
Input 1 trigger (-)White / Black
Accessory 12v (+)Yellow
Reverse trigger output (+)Purple / White
Ground (-)Black
Input 4 trigger (+)Purple
Input 4 trigger (-)Purple / Black
Input 3 trigger (+)Green
Input 3 trigger (-)Green / Black
Input 2 trigger (+)Gray
Input 2 trigger (-)Gray / Black
Expansion Port on BCI- , RP4.2-,
or RPA Module
10-Pin Plug
Wiring Connection Chart
© 2018 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global.
PAC-audio.com
P ifi A C ti
Rev. 032818
Vehicle Specic Instructions for use with RadioPRO ADVANCED
In Select 2003-2006 Chevrolet / GMC Trucks and SUVs
VS41
The VS41 is an intelligent 4 camera switcher for controlling front, rear, and blind spot cameras. It is designed to be
used with PAC radio replacement interfaces.
Introduction & Features
Important Notes
1. These instructions are specically for adding reverse, blind spot, and front cameras (or any combination of the three) to an
aftermarket radio in the following vehicles:
• 2003-2006 GM Trucks / SUVs
2. You must locate and connect to the analog turn signal wires in the vehicle, as well as connect the reverse output trigger
from the GM1A to the VS41. Please wire the VS41’s analog input triggers 1, 3 and 4 according to the instructions below.
3. Analog input trigger 2 on the VS41 only needs to be connected if you want manual activation of the front camera via toggle
switch. Automatic activation of the front camera (Input 2) via Class II Data-Bus commands can be set using the RadioPRO
PC application. See page 2 for more details on the RadioPRO PC app.
4. The reverse trigger output will provide a 150 mA 12v (+) trigger while any of the input triggers are activated.
5. The VS41 video output will always default to the signal from Input 1 when none of the input triggers are activated. This
Input is ideal for connecting the rear (reverse) camera.
6. The VS41 inputs have priority in descending numerical order. For example: If you have Input 3 or 4 triggered, then you
trigger a lower number input (for example Input 2), Input 2 will take priority over the higher numbered Input.
7. If there is poor video quality after installation of this module, please ensure quality connections on all RCA connections.
Wiring Connection Chart
Video Output
Video 1 Input - Reverse Camera
Video 2 Input - Front Camera
Video 3 Input - Left Blind Spot
Video 4 Input - Right Blind Spot
Input 1 trigger (+)White
Reverse trigger output (+)Purple / White
Input 4 trigger (+)Purple
Input 3 trigger (+)Green
Input 2 trigger (-)Gray / Black
Expansion Port on GM1A
10-Pin Plug
Any wire present on the VS41 that is not
mentioned here WILL NOT be used in this
application.
VS41 Wire
Connection
White
Reverse Trigger Input (+) -
Connect to
the Purple / White reverse trigger output provided by the GM1A
Front Camera Trigger (-) -
If you would like to manually force the front camera, hook this wire to a ground (-) trigger through a toggle switch.
Green
Left Blind Spot Trigger Input (+) - *
Dark green at turn signal switch on top of steering column. See diagrams next page.
Purple
Right Blind Spot Trigger Input (+) - *
Light green at turn signal switch on top of steering column. See diagrams next page.
Purple / White
Reverse Trigger Output (+) -
Connect this wire to the aftermarket radio's reverse trigger input.
*Please verify all signals with a multi-meter before connecting the VS41

Produkt Specifikationer

Mærke: PAC
Kategori: Skifte
Model: VS41

Har du brug for hjælp?

Hvis du har brug for hjælp til PAC VS41 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Skifte PAC Manualer

PAC

PAC VS41 Manual

8 August 2024
PAC

PAC RPA-VA1 Manual

7 August 2024

Skifte Manualer

Nyeste Skifte Manualer

Lancom

Lancom GS-2412 Manual

4 April 2025
Lancom

Lancom GS-2412P Manual

4 April 2025
Lancom

Lancom GS-2426 Manual

4 April 2025
Hager

Hager ARF970D Manual

3 April 2025
Hager

Hager ARF920D Manual

3 April 2025
Roline

Roline 14.01.3579 Manual

2 April 2025
Fantini Cosmi

Fantini Cosmi B12BN Manual

1 April 2025
Fantini Cosmi

Fantini Cosmi B12DN Manual

1 April 2025
Fantini Cosmi

Fantini Cosmi B12GN Manual

1 April 2025
Fantini Cosmi

Fantini Cosmi B12HN Manual

1 April 2025