Panasonic WV-SFR531 Manual

Panasonic Overvågningskamera WV-SFR531

Læs gratis den danske manual til Panasonic WV-SFR531 (4 sider) i kategorien Overvågningskamera. Denne vejledning er vurderet som hjælpsom af 33 personer og har en gennemsnitlig bedømmelse på 3.5 stjerner ud af 17 anmeldelser. Har du et spørgsmål om Panasonic WV-SFR531, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

WV-SFN531

(This illustration represents WV-SFN531.)

● This manual describes the installation procedures, network camera installation, cable connections,

and the angle of view adjustment.

● Before reading this manual, be sure to read the Important Information.

● This manual describes how to install the network camera using model WV-SFN531 as an example.

PGQX1909ZA es0615-0 Printed in China

Important Information ............................... 1 pc.

Installation Guide (this document) ............ 1 set

Warranty card ........................................... 1 set

CD-ROM*1 ................................................ 1 pc.

Code label*2 .............................................. 1 pc.

*1 The CD-ROM contains the operating instructions and different kinds of tool software programs.

*2 This label may be required for network management. The network administrator shall retain the

code label.

The following parts are used during installation procedures.

Ⓐ Attachment plate .................................. 1 pc.

ⒷBit (Hex wrench, screw

size 6.35 mm {1/4 inches} T10) ............... 1 pc.

Ⓒ

Template A (for the attachment plate)

...... 1 sheet

Ⓓ Power cord plug*3 ................................ 1 pc.

Ⓔ External I/O terminal plug*3 .................. 1 pc.

Ⓕ MONITOR OUT conversion plug ......... 1 pc.

Ⓖ Auxiliary handle ................................... 1 pc.

Azimuth adjustment ring

The component names of the camera are as follows. Refer to the illustration when installing or

adjusting the camera.

*2 Depending on the scanning application used, the Data Matrix may not be able to be read

correctly. In this case, access the site by directly entering the following URL.

http://security.panasonic.com/pss/security/support/qr_sp_select.html

Turn off each system’s power supply before making a connection. Before making connections,

prepare the required peripheral devices and cables.

Connect the output cable to the power cord plug (accessory).Ⓓ

Before starting the installation, check the entire system configuration. The following illustration

gives a wiring example of how to connect the camera to the network via a PoE device (hub).

LAN cable (category 5e or better, straight)

Use a LAN cable (category 5e or better, cross) when directly connecting the camera to a PC.

*1 Recommended cable length from the speaker : less than 10 m {32.8 feet}

Recommended cable length from the microphone : less than 1 m {3.28 feet}

● Since the connector storage section

does not have a sufficient space, use

audio cables and a LAN cable that do

not exceed the sizes described in the

illustrations.

● Off, input, and output of the external I/O terminal 2 and 3 can be switched by con-

figuring the setting. Refer to the operating instructions on the provided CD-ROM for

further information about the EXT I/O terminal 2 and 3 (ALARM IN2, 3) settings

(“Off”, “Alarm input”, “Alarm output” or “AUX output”).

● Connect/disconnect the audio cables and turn on the power of the camera after turning

off the power of the audio output devices. Otherwise, loud noise may be heard from

the speaker.

● Make sure that the stereo mini plug is connected to this cable. When a monaural mini

plug is connected, audio may not be heard.

When connecting a monaural speaker with amplifier, use a locally procured conversion

cable (mono-stereo).

Connect a stereo mini plug (ø3.5 mm).

● Output impedance : Approx. 600 Ω (unbalanced)

● Recommended cable length : Less than 10 m {32.8 feet}

● Output level : –20 dBV

Connect a stereo mini plug (ø3.5 mm).

● Input impedance: Approx. 2 kΩ (unbalanced)

● Recommended cable length: Less than 1 m {3.28 feet} (for microphone input)

Less than 10 m {32.8 feet} (for line input)

● Recommended microphone: Plug-in power type (option)

● Supply voltage: 2.5 V ±0.5 V

● Recommended sensitivity of microphone: –48 dB ±3 dB (0 dB=1 V/Pa,1 kHz)

● Input level for the line input: Approx. –10 dBV

● Use all 4 pairs (8 pins) of the LAN cable.

● The maximum cable length is 100 m {328 feet}.

● Make sure that the PoE device in use is compliant with IEEE802.3af standard.

● When connecting both the 12 V DC power supply and the PoE device for power

supply, 12 V DC will be used for power supply.*

* If a 12 V DC power supply and a PoE hub or router are used at the same time,

network connections may not be possible. In this case, disable the PoE settings.

Refer to the operating instructions of the PoE hub or router in use.

* In the situation where a 12 V DC power supply and a PoE hub or router are used at

the same time and the 12 V DC power supply is then disconnected, the power

supply is stopped and the camera will restart.

● When the LAN cable is disconnected once, reconnect the cable after around

2 seconds. When the cable is quickly reconnected, the power may not be supplied

from the PoE device.

● Do not connect 2 wires or more directly to a terminal. When it is necessary to connect

2 or more wires, use a splitter.

● Install external devices so that they do not exceed the rating of the network camera.

● When using the EXT I/O terminals as the output terminals, ensure they do not

cause signal collision with external signals.

● The adjustment monitor is used for checking the adjustment of the angular field of

view when installing the camera or when servicing. It is not provided for recording/

monitoring use.

● Depending on the monitor, some characters (camera title, preset ID, etc.) may not

be displayed on the screen.

● Use a switching hub or a router which is compliant with 10BASE-T/100BASE-TX.

● If a PoE hub is not used, each network camera must be connected to a 12 V DC

power supply.

● When using 12 V DC, power supply from a PoE hub or router is not required.

* Use a LAN cable (category 5e or better, 8 pins, straight).

Connect the cables of external devices to the External I/O terminal plug (accessory).Ⓔ

q When connecting an external device, strip 8 mm - 9 mm {5/16 inches - 11/32 inches} of the

outer jacket of the cable and twist the cable core to prevent the short circuit first.

Specification of cable (wire): AWG20 - AWG26, Single core, twisted

w Push down the button of the desired terminal on the external I/O terminal plug with a ball-

point pen, and release the button when the cable of the external device is fully inserted

into the terminal hole.

● Check whether the stripped part of the wire is not exposed and is securely connected.

● ALARM IN1(DAY/NIGHT IN), ALARM IN2, ALARM IN3

Input specication : No-voltage make contact input (4 V - 5 V DC, internally pulled up)

OFF : Open or 4 V - 5 V DC

ON : Make contact with GND (required drive current: 1 mA or more)

● ALARM OUT, AUX OUT

Output specication

: Open collector output (maximum applied voltage: 20 V DC)

Open : 4 V - 5 V DC by internal pull-up

Close : Output voltage 1 V DC or less (maximum drive current: 50 mA)

* The default of EXT I/O terminals is “Off”.

● The 12 V DC power supply shall be insulated from the commercial AC power.

● Be sure to use the power cord plug (accessory) provided with this product.Ⓓ

● Be sure to fully insert the power cord plug (accessory) into the 12 V DC power Ⓓ

supply terminal. Otherwise, it may damage the camera or cause malfunction.

● When installing the camera, make sure that excessive force is not applied to the

power cable.

●

Be sure to use an AC adaptor compliant with the Specifications (written in the indication

label on the bottom side of this unit) regarding power source and power consumption.

● A READILY ACCESSIBLE DISCONNECT DEVICE SHALL BE INCORPORATED

TO THE EQUIPMENT POWERED BY 12 V DC POWER SUPPLY.

● ONLY CONNECT 12 V DC CLASS 2 POWER SUPPLY (UL 1310/CSA 223) or

LIMITED POWER SOURCE (IEC/EN/UL/CSA 60950-1).

q Loosen the screw of the power cord plug (accessory), strip 3 mm to 7 mm {1/8 inches to

9/32 inches} from the end of the wire, twist the stripped part of the wire sufficiently to avoid

short circuit, and then connect the output cable to the power cord plug (accessory).

w Tighten the screw of the power cord plug. (Recommended tightening torque: 0.34 N·m

{0.25 lbf·ft})

● Check whether the stripped part of the wire is not exposed and is securely connected.

●

When connecting an external power supply to the camera, use the AWG16 to AWG24

single-wired or stranded wired cables.

ⒹⒺ

4321

Ⓑ

(Hex wrench, screw

size 6.35 mm

{1/4 inches} T10)

For U.S. and Canada:

Panasonic System Communications

Company of North America,

Unit of Panasonic Corporation

of North America

www.panasonic.com/business/

For customer support, call 1.800.528.6747

Two Riverfront Plaza, Newark, NJ 07102-5490

Panasonic Canada Inc.

5770 Ambler Drive, Mississauga,

Ontario, L4W 2T3 Canada

(905)624-5010

www.panasonic.ca

For Europe and other countries:

Panasonic Corporation

http://www.panasonic.com

Panasonic System Networks Co., Ltd.

Fukuoka, Japan

Authorised Representative in EU:

Panasonic Testing Centre

Panasonic Marketing Europe GmbH

Winsbergring 15, 22525 Hamburg, Germany

*3 The external I/O terminal plug and power cord plug are attached to the camera.

4321

Ⓔ

● When the INITIAL SET button (i.e. the initializing button) is pressed (less than 1 second) to

switch the output signal of the MONITOR OUT terminal (NTSCPAL output), the MONITOR

OUT terminal can be switched for the NTSC monitor/PAL monitor.

●

When the camera is initialized, the settings including the network settings will be initialized.

Note that the CRT key (SSL encryption key) used for the HTTPS protocol will not be initialized.

● Before initializing the settings, it is recommended to write down the settings in advance.

● Do not turn off the power of the camera during the process of initialization. Otherwise, it

may fail to initialize and may cause malfunction.

● How to initialize the camera

Follow the steps below to initialize the network camera.

Turn off the power of the camera. When using a PoE hub, disconnect the LAN cable from the camera.

When using an external power supply, disconnect the power cable connector of the camera.

Turn on the power of the camera while holding down the INITIAL SET button, and keep the INITIAL SET button

held down till the SD MOUNT indicator is lit in green (more than 10 seconds). In about 2 minutes after releasing

the INITIAL SET button, the camera will start up and the settings including the network settings will be initialized.

INITIAL SET button (Initializing / NTSC PAL switch button)

● When an SD memory card is inserted and could Lights off → Blinks green →

be recognized Lights off

● When data can be saved after the SD memory card is Lights off → Lights green

inserted and the SD ON/OFF button is pressed

(less than 1 second)

● When data can be saved to the SD memory card Lights green

● When the SD memory card is removed after holding

Lights green → Blinks green →

down the SD ON/OFF button (about 2 seconds)

Lights off (recording)

Lights green → Lights off

(waiting for recording)

●

When data cannot be saved to the SD memory card because

Lights off

an abnormality was detected or the SD memory card is

configured not to be used

● Lighting/blinking LED can be turned off with the software settings at any time. (The initial

state is lighting or blinking.) Set the LED to be solid off if necessary, depending on the

installation conditions. (☞ Operating instructions included in the CD-ROM)

SD MOUNT indicator

q When the SD ON/OFF button is pressed (less than 1 second), the SD MOUNT indicator lights

up in green and data can be saved to the SD memory card*1.

w When the SD ON/OFF button is held down (about 2 seconds), the SD MOUNT indicator lights

off and the SD memory card can be removed.

SD ON/OFF button

●

When the camera is able to communicate with the connected device

Lights orange

LINK indicator

● When data is being sent via the network camera Blinks green (accessing)

ACT indicator

Powered speaker Adjustment monitor PoE device (hub)

LAN cable

(category 5e or better, straight)

LAN cable (category

5e or better, straight)

LAN cable

(category 5e or better, straight)

Adjustment monitor

Recommended total extended

cable length*1

Microphone

Powered speaker

Microphone

● When AF (Auto Focus) operation is being executed Blinks red (1 time/second)

● When the set is being started Lights red

● When an SD memory card is recognized normally Lights red → Lights off

● When an abnormality is detected in the SD memory card Lights red → Stays red

or the SD memory card slot is not used after

the camera has started.

SD ERROR/AF indicator

WV-SFR531/WV-SFN531

WV-SFN531

*1 SDXC/SDHC/SD memory card

is described as SD memory

card.

Pan table fixing screw with washer

Auto focus (AF) button

● FRONT must positioned in

front of the camera (on the

Panasonic logo side).

MONITOR OUT

terminal (factory

shipment: NTSC

monitor)

Direction marker for installation (TOP ) Two-dimensional

barcode (Data

Matrix): To our

website*2

Screen display top (TOP)

SD memory card*1 slot

Direction marker for

installation (FRONT )

● Points up when installing to a wall.

Ⓓ Power cord

plug (accessory)

12 V DC power

supply terminal

Panning table

Enclosure Camera

Ⓐ Attachment plate

(accessory)

Ⓔ External I/O terminal plug (accessory)

Inner

cover

Dome cover

Camera xing screw

Tilting table

Ⓖ

Zoom knob

Auxiliary

handle

* Route the power cable as

shown in the following

illustration, and do not clip

the power cable when

mounting the enclosure.

● As necessary, use a

cable tie (locally

procured) to tie the

cables together.

Produkt Specifikationer

Mærke:	Panasonic
Kategori:	Overvågningskamera
Model:	WV-SFR531
Type:	IP-sikkerhedskamera
Bredde:	129.5 mm
Dybde:	129.5 mm
Højde:	102.5 mm
Vægt:	700 g
Produktfarve:	Hvid
Kompatible hukommelseskort:	SD, SDHC, SDXC
Formfaktor:	Kuppel
Relativ luftfugtighed ved drift (H-H):	10 - 90 %
Ethernet LAN:	Ja
Understøttede videoformater:	H.264
Understøttede lydformater:	LC-AAC
Driftstemperatur (T-T):	-10 - 50 °C
Maksimal opløsning:	2048 x 1536 pixel
Beskyttelsesfunktioner:	Stødresistent
Understøttelse af sprog:	CHI (SIMPL), CHI (TR), DEU, ENG, ESP, FRE, ITA, JPN, POR, RUS
Understøttede grafikopløsninger:	160 x 120,160 x 90,320 x 180,320 x 240,400 x 300,640 x 360,640 x 480 (VGA),800 x 600 (SVGA),1280 x 720 (HD 720),1280 x 960,1600 x 1200 (UXGA),1920 x 1080 (HD 1080)
Forbindelsesteknologi:	Ledningsført
Kabelteknologi:	10/100Base-T(X)
Strømkilde type:	PoE
Monteringstype:	Loft
Diameter:	129.5 mm
Indbygget kortlæser:	Ja
Full HD:	Ja
Indbygget HDD:	Ingen
Video komprimeringsformater:	H.264
Understøttet placering:	Indendørs & udendørs
Antal brugere:	14 bruger(e)
Understøttede Windows-operativsystemer:	Ja
Hvidbalance:	ATW, AWC
Sensortype:	MOS
Støjreduktion:	Ja
Digital zoom:	4 x
Normal fokuseringsområde:	0.3 - ∞ m
Autofokus:	Ja
Progressiv scanning:	Ja
Voice codecs:	G.711, G.726
Strøm over Ethernet (PoE):	Ja
Minimumsbelysning:	0.0007 Lux
Optisk sensorstørrelse:	1/3 "
Zoom kapacitet:	Ja
Nattesyn:	Ja
Billedhastighed:	60 fps
Antal kameraer:	1
Brændviddeområde:	2.8 - 9.5 mm
Effektiv sensoropløsning:	2400000 pixel
Antal sprog:	9