Paxton 477-901-US Manual

Paxton Wifi repeater 477-901-US

Læs gratis den danske manual til Paxton 477-901-US (3 sider) i kategorien Wifi repeater. Denne vejledning er vurderet som hjælpsom af 5 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 3 anmeldelser. Har du et spørgsmål om Paxton 477-901-US, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

Ins-30175-US Net2Air Ethernet bridge in plastic housing

02/04/2013

Technical Support

Technical help is available: Monday - Friday from 02:00 AM - 8:00 PM (EST)

1.800.672.7298 supportUS@paxton-access.com

Software - Requires Net2 v4.14 or later.

Documentation on all Paxton products can be found on our web site - http://www.paxton-access.com/

The access control unit connects to the Net2 software running on the PC using Paxton Net2Air proprietary

wireless technology. A Net2Air bridge enables communication from the Net2 software to the Paxton wireless

products.

Radio signals do not always behave as you might expect. For example, a cell phone that displays a full signal

on one part of the site will lose signal completely only a few feet away. These problems can be addressed by

using the Net2 site surveyor kit (690-200-US)

See also: XAN1095 - Net2 nano - How does it work? < http://paxton.info/974 >

X AN1096 - How to plan a Net2 nano installation < http://paxton.info/975 >

X Ins-30096-US - Net2Air site surveyor < http://paxton.info/1193 >

Net2Air wireless communication

Enclosure

Paxton

Radio frequency

This product should not be installed within 10 feet of other wireless equipment operating on a 2.4Ghz frequency.

To ensure optimum performance other wireless networks should avoid WiFi channels 11, 12 and 13 to reduce the

possibility of interference.

Net2Air Site Surveyor (690-200).

This access control unit uses wireless communication. It is recommended that a Net2Air site surveyor is used

to determine the best position for the bridge and control units.

Sounder

The device will 'beep' when detected by the Net2 Server Conguration Utility or when new IP settings are applied.

The sounder will also respond to a direct 'Ping' over the network. This is a feature to assist with nding devices

hidden from view.

Click on and the MAC address of the device(s) will appear in the table. You must then use the "IP address ;Detect

conguration" tab to manually assign the IP address, subnet mask and gateway.

Be aware that if the IP address that you give the device is not in the same IP range as the PC, the device will no

longer respond until you connect to it with a PC that is in the same IP range.

Some rewall/virus protection software and other wireless hardware can block the IP detection process. Disable

these and try to detect the device again. Please contact Technical Support if you require further advice.

If you detect the MAC address but the device now shows 'Not Responding', you must check the IP address, to

make sure it is still in range with the PC or network. If it is not, you should either change the IP address of the

PC or the IP address of the device so they are both again in the same range. Our Technical team can talk you

through this if you need help.

If the MAC address does not appear when you click ensure that the following ports are open on all devices

;Detect,

between this unit and the Net2 PC:-

69 UDP

6486 TCP

6488 UDP

6489 UDP

When connecting to a WAN or different subnet mask

If you are connecting this device to a remote subnet which is different from the Net2 software PC, the standard

detect mechanism cannot work across the network routers between them. The IP address, along with the correct

subnet mask and gateway for the remote subnet have to be set. Either do this on the local subnet with the

existing Net2 PC, or use a PC on the remote subnet once the device is installed.

The PC that has the Net2 server installed must be able to access the IP address range on the WAN/remote site.

This may require the routers and gateways to be congured between the networks. Again, this would be done by

the Network administrator of that site. Make sure the ports listed above are open on all intermediate routers.

Once installed, create a record with the button (if none was created during initial set up) and you should then ;Add

be able to detect its MAC by entering the IP address in the Conguration screen Ping box.

Connecting to the PC via the Ethernet port

The IP address should be assigned a xed value, or should be given a DHCP reservation. Unreserved IP addresses

issued by DHCP servers are not guaranteed to be constant, leading to potential failure of communication between

Net2 software and the bridge.

To congure the unit, run the Net2 Server Conguration Utility (Start/Programs/Net2) and Click on Net2Air Bridge.

If you still cannot detect the MAC address of the device, connect it directly to your PC via a network cable and call

our Technical Help line.

Produkt Specifikationer

Mærke:	Paxton
Kategori:	Wifi repeater
Model:	477-901-US
Vekselstrømsindgangsspænding:	100-240 V
Produktfarve:	Hvid
Produkttype:	Netværksbro
Driftstemperatur (T-T):	-20 - 55 °C
Materiale:	Plast
Netværksstandarder:	IEEE 802.3af
Frekvensbånd:	2.4 GHz
Maksimal dataoverførselshastighed:	100 Mbit/s
Strøm over Ethernet (PoE):	Ja