2
1. Large display PCE-BPD-U
Big panel displays for process signals
Big panel displays for long distance reading, for industrial ap-
plicaons. Dierent formats available with 4 and 6 digits, with
60 mm and 100 m digit height. Front keypad to access the con-
guraon menu, and oponal remote keypad.
Models to measure process signals in mA and Vdc. Provides
excitaon voltage congurable from +5 Vdc to +20 Vdc (max.
35 mA) to power up transducers. Scalable reading with se-
lectable decimal point posion.
Output
and control opons with 1, 2 and 3 relays, transis-
tor outputs, controls for SSR relays, isolated analog outputs,
c
ommunicaons in Modbus RTU, RS-485 ASCII and RS-232.
Sturdy metal housing with full IP65 protecon. Internal
connecons by plug-in screw clamp terminals, and output
through cable glands. Housing prepared for panel, wall and
hanging mount.
• Congurable ‘Fast access’ to selected funcons with key
‘UP’ (5) (see secon 1.12.11)
• ‘On power up’ for system protecon on ‘cold’ start-up
and / or acvaon of automac tare (see secon 1.12.12)
• up to 20 segments for signal linearizaon (see secon
1.12.8)
• ‘Field correcon’ for fast and easy ‘on the eld’ correcon
of osets and signal dris (see secon 1.12.3)
• alarms with 1 or 2 setpoints, independent acvaon and
deacvaon delays, hysteresis, manual unlocking, ... (see
secon 1.12.4)
• ‘Tare’ funcon for weight applicaons (see secon 1.12.14)
• ‘Peak & Hold’ for test break applicaons (see secon 1.12.9)
Mulple display lters, memory of maximum and minimum
reading, password protecon, 5 brightness levels.
1. Idenfy the instrument format (see secon 1.4)
2. Power and signal connecons
- open the instrument (see secon 1.5)
- connect the power (see secon 1.7)
- connect the signal and select jumper mA/Vdc (see sec
-
on 1.8)
- close the instrument (see secon 1.5)
3. Congure the instrument (see secon 1.12)
- select the signal range, the decimal point posion and
scale the reading (see secon 1.12.2)
4. Advanced conguraon (oponal)
- congure the instrument alarms (see secon 1.12.4)
- congure the display lters (see secon 1.12.7)
- congure the fast access (see secon 1.12.11)
- congure the excitaon voltage (see secon 1.12.15)
- congure other funcons : segment linearizaon
(1.12.8), ‘on power up’ (1.12.12), key ‘LE’ (1.12.13), tare
(1.12.14), password (1.12.16)
1.1 How to use this manual
5. If the instrument includes analog output or serial commu-
nicaons
- to include an opon to an instrument see secon 1.6
- to congure an installed opon, access the opon con-
guraon menu (see secon 1.12.20)
6. Install the instrument
- mount on panel, wall or hanging (see secon 1.16)
- adjust the brightness level according to your environmen
-
tal needs (see secon 1.12.19)
If
this is the rst me you are conguring a big panel display,
below are the steps to follow to install and congure the in-
strument.
R
ead all the manual secons in order to have a full and clear
view of the characteriscs of the instrument. Do not forget
to read the installaon precauons at secon 1.17.
