PCE Instruments PCE-DMM 11 Manual

PCE Instruments Måling PCE-DMM 11

Læs gratis den danske manual til PCE Instruments PCE-DMM 11 (2 sider) i kategorien Måling. Denne vejledning er vurderet som hjælpsom af 47 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 24 anmeldelser. Har du et spørgsmål om PCE Instruments PCE-DMM 11, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

User manual

Manometer PCE-D M 10, M PCE- M 1DM 1

1. General information

1.1 Information on the operati ng manual

This operating manual contains important information on

proper usage of the device. Read this operating manual

carefully before installing and starting up the pressure

measuring device.

Adhere to the safety notes and operating instructions which

are given in the operating manual. Additionally applicable

regulations regarding occupational safety, accident

prevention as well as national installation standards and

engineering rules must be complied with!

This operating manual is part of the device and must be kept

at a, for the personnel always accessible location, close to

the installation position of the device.

This operating manual is copyrighted. The contents of this

operating manual reflect the version available at the time of

printing. It has been issued to our best knowledge and belief.

However, errors may have occurred. For incorrect

statements and their consequences, liability cannot be

assumed by PCE Instruments.

– – Technical modifications reserved

1.2 Symbols used

DANGER! Dangerous – situation, which may result in

serious or fatal injuries

WARNING! - Potentially dangerous situation, which

may result in fatal or serious injuries

CAUTION! – Potentially dangerous situation, which may

result in minor injuries

!CAUTION! – ally dangerous situation, which mayPotenti

result in damage of objects

NOTE – Tips and information for the user to ensure

good conditions for the operation.

1.3 Target group

WARNING! To avoid hazards for the operator and

damages of the device, following described instructions

have to be worked out by qualified technical personnel.

1.4 Limitation of liability

No liability is assumed and warranty claims are excluded in

case of non-observance of the operating manual, improper

application, modification of or damage to the device.

1.5 Intended use

- The battery powered digital pressure gauge PCE-DMM

1X has exclusively designed applications been for in

hydraulics pneumatics as well for mechanical and as

engineering. It can be easily and quickly installed in situ.

- It is in of user the responsibility the to verify thewhether

chosen device is the intended application. suitable for In

case of any our doubts, contact sales department to

eliminat indistinctnee any ss. PCE Instruments does

not assume any an and liability for incorrect selection

its consequences!

- Permissibl g or liquid s in thee media are ases s, pecified

data sheet. operator ensure Additionally the has to that

the wetted medium compatible the media is with parts,

for the intended application.

WARNING! – Danger through improper usage!

1.6 Package contents

Please verify that all listed parts are undamaged included in

the delivery and check for consistency specied in your

order:

- 10 digital pr gaugeessure PCE-DM Mor D M 1PCE- M 1

-user manual

1.7 UL – Approval devices -identication) (for with UL

The UL –Approval was done with respect to U.S. standards

norms which also correspond with the applicable Canadian

standards norms for safety.

Note the following points, so that devices fulls the demands

of UL approval:

- The transmitter shall be supplied by Limited Energy

Source (per UL 61010) or NEC Class 2 Power Source.

- only indoor use

- maximum operating voltage: see technical data

- use only batteries with UL certification

2. Installation

2.1 Mounting an safetyd instructions

WARNING! Install the device only when depressurized

and currentless!

WARNING! This device may only be installed by

qualified technical personnel who has read and

understood the operating manual!

!Handle this electronic precision measuring device

carefully in packed as well as in unpacked condition!

!The device must not be subject to any changes or

modifications.

!The device may not be thrown!

!To avoid damaging the diaphragm, remove packaging

and protective cap only directly before starting up the

device. A delivered protective cap must be stored!

Place the protective cap on the pressure port again

immediately after disassembling.

!Handle the unprotected diaphragm very carefully - it is

very sensitive and may be easily damaged.

!Do not use any force when installing the device to

prevent damage of the device and the plant!

Take care that no mechanical stresses occur at the

pressure port as a result of the installation, since this

may cause a shifting of the characteristic curve.

In hydraulic systems, position the device in such a way

that the pressure port points upward (venting).

Provide a cooling line when using the device in steam

lines.

2.2 General installation steps

- Carefully remove the pressure measuring device from

the package and dispose of the package properly.

- Then go ahead as detailed in the specic instructions

below.

2.3 Installation steps for 3852 DIN

DO NOT USE ANY ADDITIONAL SEALING MATERI-

ALS, LIKE YARN, HEMP OR TEFLON TAPE!

- Check to ensure the proper groove tting of the o-ring

and additionally to ensure no damage to the o- ring.

- Ensure that the sealing surface of the taking part is

perfectly smooth and clean. (RZ 3.2)

- Screw the device into the corresponding thread by

hand.

- If you have a device with a knurled ring, the transmitter

has to be screwed in by hand only.

- Devices with a spanner flat have to be tightened with an

open-end wrench (wrench size of steel: G1/4": approx.

5 Nm; G1/2": approx. 10 Nm; G3/4": approx. 15 Nm;

G1": approx. 20 Nm; G1 1/2": approx. 25 Nm; wrench

size of plastic: max. 3 Nm).

-The indicated tightening torques must not be

exceeded!

2.4 Installation steps for 837 EN

- Use a suitable seal, corresponding to the medium and

the pressure input (e. g. a cooper gasket).

- Ensure that the sealing surface of the taking part is

perfectly smooth and clean. (RZ 6.3)

- Screw the device into the corresponding thread by

hand.

- Tighten it with a wrench (for G1/4": approx. 20 Nm; for

G1/2": approx. 50 Nm).

-The indicated tightening torques must not be

exceeded!

2.5 Installation steps for NPT

- -strip).Use a suitable seal (e. g. a PTFE

- Screw the device into the corresponding thread by

hand.

- Nm;Tighten it with a wrench (for 1/4" NPT: approx. 30

for 1/2" NPT: approx. 70 Nm).

-The indicated tightening torques must not be

exceeded!

2.6 Installation steps for 6” 7/1 -20 UNF (DM 17)

- Do NOT use any additional sealing materials!

- Screw the device into the corresponding thread by

hand.

- 20 Nm).Tighten it with a wrench (approx.

-The indicated tightening torques must not be

exceeded!

PCE Americas Inc.

711 Commerce Way

Suite 8

Jupiter

FL-33458

USA

From outside US: +1

Tel: (561) 320-9162

Fax: (561) 320-9176

info@pce-americas.com

www.pce-instruments.com/english

www.pce-instruments.com

PCE Instruments UK Ltd.

Unit 11

Southpoint Business Park

Ensign way

Hampshire / Southampton

United Kingdom, SO31 4RF

From outside UK: +44

Tel: (0) 2380 98703 0

Fax: (0) 2380 98703 9

info@pce-instruments.co.uk

2.7 Positioning of the display module

The display module of the pressure gauge is rotatable so

that clear readability is guaranteed even on unusual

installation positions.

Fig. 1 display module

Produkt Specifikationer

Mærke:	PCE Instruments
Kategori:	Måling
Model:	PCE-DMM 11

Har du brug for hjælp?

Hvis du har brug for hjælp til PCE Instruments PCE-DMM 11 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Måling PCE Instruments Manualer

PCE Instruments PCE-P18D Manual

9 December 2025

PCE Instruments PCE-N25S Manual

5 December 2025

PCE Instruments PCE-N24S Manual

3 December 2025

PCE Instruments PCE-CSM 100 Manual

11 November 2025

PCE Instruments PCE-RD 65 Manual

9 November 2025

PCE Instruments PCE-STM 10 Manual

7 November 2025

PCE Instruments PCE-MOV 60 Manual

7 November 2025

PCE Instruments PCE-VOC 5 Manual

7 November 2025

PCE Instruments PCE-P18-2A Manual

6 November 2025

PCE Instruments PCE-HFG 2.5K Manual

5 November 2025

Måling Manualer

Nyeste Måling Manualer

PeakTech 5605 A Manual

16 December 2025

16 December 2025

16 December 2025

16 December 2025

16 December 2025

16 December 2025

16 December 2025

Mitsubishi SRK25ZSH-WF Manual

16 December 2025

Mitsubishi SRK71ZRH-WF Manual

15 December 2025

Mitsubishi SRK50ZSXH-WF Manual

15 December 2025