Phoenix UPS-BAT/LI-ION/24DC/120WH Manual

Phoenix power bank UPS-BAT/LI-ION/24DC/120WH

Læs nedenfor 📖 manual på dansk for Phoenix UPS-BAT/LI-ION/24DC/120WH (66 sider) i kategorien power bank. Denne guide var nyttig for 7 personer og blev bedømt med 4.2 stjerner i gennemsnit af 4 brugere

Download PDF

Side 1/66

Power Supplies

User Manual

UPS-CONF

Order No.: -

Configuration and Management Software

UPS-CONF

2.1 System requirements

In order to run the UPS-CONF software, your computer must meet the following software and

hardware requirements:

Software requirements

• Supported operating systems:

- Windows 7, 32bit and 64bit

- Windows Vista SP1

- XP SP3 (requires .NET Framework 3.5 SP1)

• Supported browser: Internet Explorer version 6 or later

Hardware requirements

CPU 1 GHz min.

2 GHz recommended

Windows 7

Windows Vista SP1

Pentium III 1GHz min.

2 GHz recommended

Windows XP SP3

Main memory 1 GB RAM min.

2 GB RAM recommended

Windows 7

Windows Vista SP1

512 MB RAM min.

1 GB RAM recommended

Windows XP SP3

Main memory used by UPS-CONF max. 96 MB

Hard disk drive (recommended)

Hard disk used by UPS-CONF

850 MB

max. 50 MB

CD-ROM drive not necessarily needed

Interfaces 1 x USB 2.0

Monitor VGA, resolution 800 x 600 pixels minimum, 256 colors

Network Internet connection needed for program download

UPS-CONF

PHOENIX CONTACT 104779_en_01

4.3 Connecting the PC

A PC has to be connected to the UPS in one of the following cases:

• You want to configure or monitor the UPS by the UPS-CONF software.

• You want to display currently set QUINT-UPS parameters or modify them using UPS-

CONF.

• You want to initiate a controlled PC shutdown in case of a mains failure and if battery

runs low.

NOTE

First, install the software (see page 5) and then connect the PC afterwards.

To connect the PC to the QUINT-UPS, proceed as follows:

1. Connect the USB connector of the IFS-USB-DATACABLE to a free USB connector of

your PC. After detecting the device, the used USB port is entered automatically in the

software settings of UPS-CONF.

2. Connect the other side of the IFS-USB-DATACABLE to the Data port of the UPS:

UPS-CONF

PHOENIX CONTACT 104779_en_01

Battery parameters Meaning

Quantity check o.k. Shows "Yes", if the number of installed bat-

tery units complies with the number of detec-

ted batteries. Otherwise "No" is displayed.

6.3 Battery Advanced

This navigation item is only available if the "Enable advanced views" checkbox is marked in

the software settings (see page 5).

If the "Battery Advanced" item is selected in the software menu "Status", advanced status

information for all connected batteries is shown in the action area.

In normal operation it looks something like this:

UPS-CONF

PHOENIX CONTACT 104779_en_01

A reported alarm is additionally signaled by the LED at the front of the UPS device as well as

in the status bar of the UPS-CONF software.

By means of warnings and alarms you can implement a two-level detection system:

1. Report a warning, when the first threshold value is exceeded.

Example: battery lifetime is still one year.

2. Report an alarm, when the second threshold value is exceeded.

Example: remaining lifetime of the battery is only some few months or weeks. Now an

Email is additionally sent to the responsible person to ensure that a new battery is

ordered in time.

UPS-CONF

PHOENIX CONTACT 104779_en_01

Produkt Specifikationer

Mærke:	Phoenix
Kategori:	power bank
Model:	UPS-BAT/LI-ION/24DC/120WH
Kode for international beskyttelse (IP):	IP20
Bredde:	135 mm
Dybde:	110 mm
Højde:	202 mm
Vægt:	2900 g
Produktfarve:	Grå
Batterispænding:	24 V
Batterikapacitet:	120 Wh
Indbygget skærm:	Ingen
Batteriteknologi:	Lithium-Ion (Li-Ion)
Opbevaringstemperatur (T-T):	-40 - 65 °C
Driftstemperatur (T-T):	-20 - 60 °C
Vandfast:	Ingen
Certificering:	IP20
Udgangsspænding:	24 V
Udgangsstrøm:	30 A
Indgangsspænding:	24 V
Opladningskilde:	DC
Oprindelsesland:	Kina