Pioneer HTZ151DVD Manual
Pioneer
Hjemmesystem
HTZ151DVD
Læs nedenfor 📖 manual på dansk for Pioneer HTZ151DVD (85 sider) i kategorien Hjemmesystem. Denne guide var nyttig for 25 personer og blev bedømt med 3.6 stjerner i gennemsnit af 13 brugere
Side 1/85
Operating Instructions
Location: bottom of the unit
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated
"dangerous voltage" within the product's
enclosure that may be of sufficient
magnitude to constitute a risk of electric
shock to persons.
CAUTION:
TO PREVENT THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR
BACK). NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
IMPORTANT
D3-4-2-1-1_En-A
WARNING
This equipment is not waterproof. To prevent a fire
or shock hazard, do not place any container filed
with liquid near this equipment (such as a vase or
flower pot) or expose it to dripping, splashing, rain
or moisture. D3-4-2-1-3_A_En
WARNING:
BEFORE PLUGGING IN THE UNIT FOR THE FIRST
TIME, READ THE FOLLOWING SECTION CAREFULLY.
The voltage of the available power supply differs
according to country or region. Be sure that the
power supply voltage of the area where this unit
will be used meets the required voltage (e.g., 230V
or 120V) written on the rear panel.
D3-4-2-1-4_En
WARNING
To prevent a fire hazard, do not place any naked
flame sources (such as a lighted candle) on the
equipment.
D3-4-2-1-7a_A_En
VENTILATION CAUTION
When installing this unit, make sure to leave space
around the unit for ventilation to improve heat
radiation (at least 10 cm at top, 10 cm at rear, and
10 cm at each side).
WARNING
Slots and openings in the cabinet are provided for
ventilation to ensure reliable operation of the
product, and to protect it from overheating. To
prevent fire hazard, the openings should never be
blocked or covered with items (such as newspapers,
table-cloths, curtains) or by operating the
equipment on thick carpet or a bed.
D3-4-2-1-7b_A_En
CAUTION
The STANDBY/ON switch on this unit will not
completely shut off all power from the AC outlet.
Since the power cord serves as the main disconnect
device for the unit, you will need to unplug it from
the AC outlet to shut down all power. Therefore,
make sure the unit has been installed so that the
power cord can be easily unplugged from the AC
outlet in case of an accident. To avoid fire hazard,
the power cord should also be unplugged from the
AC outlet when left unused for a long period of time
(for example, when on vacation).
D3-4-2-2-2a_A_En
Thank you for buying this Pioneer product.
Please read through these operating instructions so that you will know how to operate your model
properly. After you have finished reading the instructions, put them in a safe place for future reference
.
Operating Environment
Operating environment temperature and humidity:
+5 ºC – +35 ºC (+41 ºF – +95 ºF); less than 85 %RH
(cooling vents not blocked)
Do not install this unit in a poorly ventilated area, or in
locations exposed to high humidity or direct sunlight (or
strong artificial light) D3-4-2-1-7c_A_En
CAUTION
This product is a class 1 laser product, but this product
contains a laser diode higher than Class 1.
To ensure continued safety, do not remove any covers or
attempt to gain access to the inside of the product.
Refer all servicing to qualified personnel.
The following caution label appears on your unit.
Location: top of the unit
[Taiwanese model]
CLASS 1
LASER PRODUCT
D3-4-2-1-8_B_En
[All other models]
CAUTION : CLASS 3B VISIBLE AND INVISIBLE LASER
VRW2159
EXPOSURE TO THE BEAM.
RADIATION WHEN OPEN, AVOID
If the AC plug of this unit does not match the AC
outlet you want to use, the plug must be removed
and appropriate one fitted. Replacement and
mounting of an AC plug on the power supply cord of
this unit should be performed only by qualified
service personnel. If connected to an AC outlet, the
cut-off plug can cause severe electrical shock. Make
sure it is properly disposed of after removal.
The equipment should be disconnected by removing
the mains plug from the wall socket when left
unused for a long period of time (for example, when
on vacation). D3-4-2-2-1a_A_En
POWER-CORD CAUTION
Handle the power cord by the plug. Do not pull out the
plug by tugging the cord and never touch the power
cord when your hands are wet as this could cause a
short circuit or electric shock. Do not place the unit, a
piece of furniture, etc., on the power cord, or pinch the
cord. Never make a knot in the cord or tie it with other
cords. The power cords should be routed such that they
are not likely to be stepped on. A damaged power cord
can cause a fire or give you an electrical shock. Check
the power cord once in a while. When you find it
damaged, ask your nearest PIONEER authorized
service center or your dealer for a replacement.
S002_En
This product is for general household purposes. Any
failure due to use for other than household purposes
(such as long-term use for business purposes in a
restaurant or use in a car or ship) and which
requires repair will be charged for even during the
warranty period. K041_En
4
En
01 Controls and displays
Front panel . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Remote control. . . . . . . . . . . . . . . . . . . . . . . . 6
Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
02 Getting started
Home theater sound setup . . . . . . . . . . . . . . . 9
Setting the channel levels . . . . . . . . . . . . . . 9
Using the on-screen displays . . . . . . . . . . . . 10
Playing discs . . . . . . . . . . . . . . . . . . . . . . . . 10
Basic playback controls . . . . . . . . . . . . . . . 10
Resume and Last Memory . . . . . . . . . . . . . 11
DVD-Video disc menus. . . . . . . . . . . . . . . . 11
Video CD/Super VCD PBC menus . . . . . . . 11
Listening to the radio . . . . . . . . . . . . . . . . . . 12
Improving poor FM reception . . . . . . . . . . . 12
Memorizing stations. . . . . . . . . . . . . . . . . . 12
Listening to station presets . . . . . . . . . . . . 12
Listening to other sources . . . . . . . . . . . . . . 12
Setting the sleep timer . . . . . . . . . . . . . . . . . 13
Dimming the display. . . . . . . . . . . . . . . . . . . 13
03 Listening to your system
Auto listening mode . . . . . . . . . . . . . . . . . . . 14
Listening in surround sound . . . . . . . . . . . . . 14
Using Front Surround. . . . . . . . . . . . . . . . . . 14
Listening in stereo . . . . . . . . . . . . . . . . . . . . 15
Listening with headphones . . . . . . . . . . . . 15
Using the SFC modes . . . . . . . . . . . . . . . . . . 15
Adjusting the bass and treble . . . . . . . . . . . . 15
Boosting the bass level. . . . . . . . . . . . . . . . . 15
04 Disc playback features
Scanning discs . . . . . . . . . . . . . . . . . . . . . . . 16
Playing in slow motion . . . . . . . . . . . . . . . . . 16
Frame advance/frame reverse. . . . . . . . . . . . 16
Playing a JPEG slideshow. . . . . . . . . . . . . . . 16
Browsing DVD or Video CD/Super VCD discs
with the Disc Navigator. . . . . . . . . . . . . . . . . 17
Browsing WMA, MP3, MPEG-4 AAC, DivX
video and JPEG files with the Disc
Navigator . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Looping a section of a disc . . . . . . . . . . . . . . 18
Using repeat play . . . . . . . . . . . . . . . . . . . . . 18
Using random play . . . . . . . . . . . . . . . . . . . . 19
Creating a program list. . . . . . . . . . . . . . . . . 19
Other functions available from the program
menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Searching a disc. . . . . . . . . . . . . . . . . . . . . . 20
Switching subtitles . . . . . . . . . . . . . . . . . . . . 20
Switching language / audio channels. . . . . . 20
Zooming the screen . . . . . . . . . . . . . . . . . . . 21
Switching camera angles . . . . . . . . . . . . . . . 21
Displaying disc information . . . . . . . . . . . . . 21
05 USB playback
Using the USB interface . . . . . . . . . . . . . . . . 22
Basic playback controls . . . . . . . . . . . . . . . . 22
Scanning files . . . . . . . . . . . . . . . . . . . . . . . . 23
Playing a JPEG slideshow . . . . . . . . . . . . . . . 23
Browsing files with the Navigator . . . . . . . . . 23
06 Audio Settings and Video Adjust
menus
Audio Settings menu. . . . . . . . . . . . . . . . . . . 24
Audio DRC . . . . . . . . . . . . . . . . . . . . . . . . . 24
Video Adjust menu . . . . . . . . . . . . . . . . . . . . 24
07 Initial Settings menu
Using the Initial Settings menu . . . . . . . . . . . 25
Video Output settings . . . . . . . . . . . . . . . . . . 25
Language settings. . . . . . . . . . . . . . . . . . . . . 25
Display settings. . . . . . . . . . . . . . . . . . . . . . . 26
Options settings . . . . . . . . . . . . . . . . . . . . . . 26
Speakers settings . . . . . . . . . . . . . . . . . . . . . 26
Parental Lock . . . . . . . . . . . . . . . . . . . . . . . 26
About DivX® VOD content . . . . . . . . . . . . . 27
Speaker Distance . . . . . . . . . . . . . . . . . . . . 28
08 Other connections
Connecting external antennas. . . . . . . . . . . . 29
Connecting auxiliary audio components . . . . 29
Connecting the S-video output . . . . . . . . . . . 29
Connecting using the component video
output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
About progressive scan video . . . . . . . . . . . 30
09 Additional information
Disc / content format playback
compatibility . . . . . . . . . . . . . . . . . . . . . . . . . 31
Disc compatibility table . . . . . . . . . . . . . . . 31
About DVD+R/DVD+RW compatibility . . . 32
About DivX . . . . . . . . . . . . . . . . . . . . . . . . . 32
About MPEG-4 AAC . . . . . . . . . . . . . . . . . . 33
About WMA . . . . . . . . . . . . . . . . . . . . . . . . 33
Using and taking care of discs . . . . . . . . . . . 33
DVD Video regions . . . . . . . . . . . . . . . . . . . 34
Installation and maintenance . . . . . . . . . . . . 34
Hints on installation . . . . . . . . . . . . . . . . . . 34
Cleaning the pickup lens . . . . . . . . . . . . . . 34
Problems with condensation . . . . . . . . . . . 34
Moving the system unit. . . . . . . . . . . . . . . . 34
Screen sizes and disc formats. . . . . . . . . . . . 35
TV system setting . . . . . . . . . . . . . . . . . . . . . 35
Frequency step setting . . . . . . . . . . . . . . . . . 35
Contents
5
En
English FrançaisDeutsch
Nederlands
Italiano Español
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . 36
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
DVD/CD/Video CD player . . . . . . . . . . . . . . 37
Tuner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
USB connection . . . . . . . . . . . . . . . . . . . . . 38
Error Messages. . . . . . . . . . . . . . . . . . . . . . 39
Resetting the system. . . . . . . . . . . . . . . . . . . 39
Setting the Key Lock . . . . . . . . . . . . . . . . . . . 39
Switching off the demo . . . . . . . . . . . . . . . . . 39
Using the language code list. . . . . . . . . . . . . 39
Language code list . . . . . . . . . . . . . . . . . . . . 40
Country/Area code list. . . . . . . . . . . . . . . . . . 40
Specifications . . . . . . . . . . . . . . . . . . . . . . . . 41
Controls and displays01
6
En
Chapter 1
Controls and displays
Front panel
1
OPEN/CLOSE
Opens/closes the disc tray.
2
DVD/CD
Selects the DVD/CD function and starts/
pauses/resumes playback.
3
Stops playback.
4
USB
Selects the USB function and starts/pauses
playback.
5
VOLUME
buttons
6
STANDBY/ON
Switches the system on or into standby.
7
USB
interface
Connect a USB device for playback (see USB
playback on page 22).
8 PHONES jack
Connect headphones.
9 Display
See Display below.
Remote control
1
STANDBY/ON
Switches the system on or into standby.
2 Function select buttons
Selects the source you want to listen to (DVD/
CD, TUNER, USB, LINE).
3 Number buttons / CLEAR /
DISPLAY
CLEAR
Clears an entry.
DVD/CD
VOLUME
OPEN/CLOSE
USB
STANDBY/ON
3 4 5 621
7 8
9
TV CONTROL
VOLUME
HOME
MENU
AUDIO
SUBTITLE
ANGLE
ZOOM
STANDBY
/ON
MUTE
LINE
TOP MENU
RETURN
TEST TONE SOUND
CLEAR
SLEEP
DISPLAY
1 2 3
4 5 6
7 8 9
0
SURROUND
TU NE
TU NE
ST
ST
ENTER
USB
SETUP
MENU
OPEN/
CLOSE
INPUT CHANNEL VOLUME
DVD/CD TUNER
(FM/AM)
1
2
3
8
9
4
7
11
12
13
14
15
16
5
6
10
Controls and displays 01
7
En
English FrançaisDeutsch
Nederlands
Italiano Español
DISPLAY
Displays/changes disc information shown
on-screen (page 21).
4
TOP MENU
Displays the top menu of a DVD disc in the
play position—this may be the same as
pressing MENU (page 11).
5 Cursor buttons,
ENTER
and tuning
buttons
Cursor buttons
Use the cursor buttons (/// ) to
navigate on-screen displays and menus.
ENTER
Selects an option or executes a command.
TUNE +/–
Tunes the radio.
ST +/–
Selects station presets when listening to
the radio.
6
HOME MENU
Displays (or exits) the on-screen menu for
Initial Settings, Play Mode functions, etc.
7 Setup and other sound controls
SETUP
Use to make various system and surround
sound settings (page 9, 12, 14, 35 and 39).
TEST TONE
Outputs the test tone (for speaker setup)
(page 9).
SURROUND
Selects a Surround mode (page 14) or
switches to stereo playback (page 15).
SOUND
Accesses the sound menu to adjust the
SFC Mode, bass and treble, etc. (page 15)
8 Playback controls
See Basic playback controls on page 10, Disc
playback features on page 16 and USB playback
on page 22 for an explanation of these
controls.
9 TV CONTROL buttons
These control Pioneer plasma displays.
10
MUTE
Mutes the sound (press again to cancel).
11
OPEN/CLOSE
Opens/closes the disc tray.
12 DVD controls
AUDIO
Selects audio channel/language (page 20).
SUBTITLE
Displays/changes the subtitles (page 20).
ANGLE
Changes camera angle during DVD multi-
angle scene playback (page 21).
ZOOM
Changes the screen zoom level (page 21).
13
MENU
Press to display a DVD disc or USB menu, or
the Navigator (page 17 and 23).
14
RETURN
Returns to a previous menu screen.
15
SLEEP
Press to set the sleep timer (page 13).
16
VOLUME +/–
Adjusts the volume.
Controls and displays
8
En
Display
1
DTS
Lights during playback of a DTS source
(page 14).
2 PRGSVE
Lights when progressive scan video output is
selected (page 30).
3
SOUND
Lights when the SFC Modes or the tone
controls (treble, bass or bass boost) are active
(page 15).
4
F.SURR.
(XV-DV151 model only)
Lights when the Front Surround listening
mode is selected (page 14).
5
RPT
and
RPT
-1
RPT
lights during repeat play. RPT-1 lights
during repeat one-track play (page 18).
6
PGM
Lights during program play (page 19).
7 Tuner indicators
– Lights when a broadcast is being
received.
– Lights when a stereo FM broadcast is
being received in auto stereo mode.
– Lights when FM mono reception is
selected.
8
RDM
Lights during random play (page 19).
9 kHz / MHz
Indicates the frequency unit shown in the
character display ( kHz for AM, MHz for FM).
10 Character display
11
Lights when sleep timer is active (page 13).
12
Lights during playback.
13
2
PL II
Lights during Dolby Pro Logic II decoding
(page 14).
14
2
D
Lights during playback of a Dolby Digital
source (page 14).
PRGSVE SOUND
DTS F.SURR.
2PL
2D
RPT -1
kHz
PGM
MHz RDM
6
12 89 7
54
1113
3
14 10
21
Getting started 02
9
En
English FrançaisDeutsch
Nederlands
Italiano Español
Chapter 2
Getting started
Home theater sound setup
Place your speakers as shown below for
optimal surround sound (see the Speaker
Setup Guide for more placement tips).
•Standard surround 5-spot setup – This is
a standard multichannel surround sound
speaker setup for optimal 5.1 channel
home theater sound.
XV-DV151 only:
Depending on the size and
characteristics of your room, you can choose
to use the following setup option: 1
•Front surround 3-spot setup – This setup
is ideal when rear surround speaker
placement isn't possible or you want to
avoid running long speaker cables in your
listening area. Use this setup together with
the Front Surround modes to take
advantage of wall and ceiling reflections
for a very realistic surround effect.
After placing your speakers, complete Setting
the channel levels below then refer to Speakers
settings on page 26 to complete your surround
sound setup.
Setting the channel levels
Set the relative channel levels from your main
listening position. 2
1 Press
TEST TONE
.
The test tone is output in the following order
(from the speakers active in the current
listening mode):
•L – Front left speaker
•C
– Center speaker
•R
– Front right speaker
•SR – Right surround speaker
•SL – Left surround speaker
•SW – Subwoofer 3
2 Use the VOLUME +/– button to adjust
the volume to an appropriate level.
3 Use / to adjust the speaker levels in
turn.
You should hear the test tone at the same
volume from each speaker when seated in the
main listening position. The channel level
range is ± 10 dB.
4 When you’re done, press ENTER to exit
test tone setup.
Note
1 When using this setup, make sure the front surround mode is switched on (page 14) before selecting any surround mode.
Front left
Surround
left
Listening position
Center
Subwoofer
Front right
Surround
right
Front
left
Front
right
Surround
left
Surround
right
Listening position
Center
Subwoofer
2 • This is only available when DVD/CD is selected and playback is stopped. Also make sure headphones are unplugged.
• To adjust the overall balance while listening to any sound source you want, press SETUP, use / to select CH LEVEL
then
press ENTER
. Use / to move channel to channel, and / to adjust the channel levels. Press ENTER
when you’re finished.
3 Since the subwoofer produces ultra-low frequencies its sound may seem quieter than it actually is.
Getting started2
10
En
Using the on-screen displays
For ease of use, this system makes extensive
use of graphical on-screen displays (OSDs).
All the screens are navigated in basically the
same way, using , , , to change the
highlighted item and pressing ENTER
to select
it.1
Important
• Throughout this manual, ‘Select’ means
use the cursor buttons to highlight an item
on-screen, then press ENTER
.
Tip
• The button guide at the bottom of every
OSD screen shows you which buttons
you’ll need to use for that screen.
Playing discs
The basic playback controls for playing DVD,
CD, Video CD/Super VCD, DivX video and
WMA/MP3/MPEG-4 AAC discs are covered
here.
Further functions are detailed in chapter 4.
1 If the player isn’t already on, switch it on.
If you’re playing a disc with video, also turn on
your TV and make sure that it is set to the
correct video input.
2 Press
OPEN/CLOSE
to load a disc.
Load a disc with the label side facing up, using
the disc tray guide to align the disc (if you’re
loading a double-sided DVD disc, load it with
the side you want to play face down).
3 Press
(play) to start playback.
If you’re playing a DVD or Video CD/Super VCD,
a menu may appear. See DVD-Video disc
menus and Video CD/Super VCD PBC menus on
page 11 to navigate these.
If you loaded a disc containing JPEGs, a
slideshow will start. See Playing a JPEG
slideshow on page 16 for more on this.
• If a disc contains a mixture of DivX video
and other media file types (MP3, for
example), first select whether to play the
DivX video files (
DivX) or the other media
file types ( MP3 / WMA / JPEG / MPEG-4
AAC) from the on-screen display.
4 Adjust the volume.
Use the VOLUME control.
Basic playback controls
The following table shows the basic controls on
the remote for playing discs 2. You can find
other playback features in the chapter 4.
Note
1 The screen saver will appear after five minutes of inactivity.
Button What it does
HOME
MENU
Displays/exits the on-screen display
Changes the highlighted menu item
ENTER Selects the highlighted menu item
RETURN Returns to the main menu without
saving changes
2 You may find with some DVD discs that some playback controls don’t work in certain parts of the disc.
Button What it does
Starts/resumes normal playback.
• If the display shows RESUME
or
LAST MEM
playback starts from the
resume or last memory point (see
Resume and Last Memory below).
Pauses/unpauses a disc.
Stops playback or cancels the resume
function (if the display shows
RESUME
).
Getting started 02
11
En
English FrançaisDeutsch
Nederlands
Italiano Español
Resume and Last Memory
When you stop playback of a disc, RESUME
shows in the display indicating that you can
resume playback from that point.
With DVDs and Video CD/Super VCDs, even if
ejected, the play position is stored in memory. 1
The next time you load the disc, the display
shows LAST MEM and you can resume play-
back.
If you want to clear the resume point, press
(stop) while RESUME is displayed.
DVD-Video disc menus
Many DVD-Video discs contain menus from
which you can select what you want to watch.
Sometimes DVD-Video menus are displayed
automatically when you start playback; others
only appear when you press MENU or TOP
MENU .
Video CD/Super VCD PBC menus
Some Video CD/Super VCDs have menus from
which you can choose what you want to watch.
These are PBC (Playback control) menus.
You can play a PBC Video CD/Super VCD
without having to navigate the PBC menu by
starting playback using a number button to
select a track, rather than the (play) button.
Press to start fast reverse scanning.
Press to start fast forward scanning.
Skips to the start of the current track or
chapter, then previous tracks/chapters.
Skips to the next track or chapter.
Numbers
Use to enter a title/chapter/track
number. Press ENTER
to select.
• If the disc is stopped, playback starts
from the selected title (for DVD) or
track (for CD/Video CD/Super VCD).
• If the disc is playing, playback jumps
to the start of the selected title (VR
mode DVD-RW), chapter (DVD-Video)
or track (CD/Video CD/Super VCD).
Note
1 • The Last Memory function may not work with some discs.
• For DVD-Video discs (except VR mode DVD-R/RW), the player stores the play position of the last five discs.
Button What it does
TOP MENU Displays the ‘top menu’ of a DVD
disc—this varies with the disc.
Button What it does
MENU Displays a DVD disc menu—this
varies with the disc and may be
the same as the ‘top menu’.
Moves the cursor around the
screen.
ENTER Selects the current menu option.
RETURN Returns to the previously
displayed menu screen.
Numbers Highlights a numbered menu
option (some discs only). Press
ENTER
to select.
Button What it does
RETURN Displays the PBC menu.
Numbers Selects numbered menu options.
Press ENTER
to select.
Displays the previous menu page
(if there is one).
Displays the next menu page (if
there is one).
Button What it does
Getting started2
12
En
Listening to the radio
The tuner can receive both FM and AM
broadcasts, and lets you memorize your
favorite stations so you don’t have to manually
tune in every time you want to listen.
1 Press
TUNER
to switch to the tuner, then
press repeatedly to select the AM or FM band.
The display shows the band and frequency.
2 Tune to a frequency.
There are three tuning modes—manual, auto,
and high-speed:
•Manual tuning : Press TUNE +/–
repeatedly to change the displayed
frequency.
•Auto tuning : Press and hold TUNE +/–
until the frequency display starts to move,
then release. The tuner will stop on the next
station it finds. Repeat to keep searching.
•High-speed tuning : Press and hold TUNE
+/– until the frequency display starts to
move rapidly. Keep the button held down
until you reach the frequency you want. If
necessary, fine tune the frequency using
the manual tuning method.
Improving poor FM reception
If you’re listening to an FM station in stereo but
the reception is weak, you can improve the
sound quality by switching to mono.
1 Tune to an FM radio station then press
SETUP
.
2 Use
/
to choose FM MODE then press
ENTER
.
3 Use
/
to select
FM MONO
then press
ENTER
.
The mono indicator ( ) lights when the tuner
is in mono reception mode.
Select FM AUTO above to switch back to auto-
stereo mode (the stereo indicator ( ) lights
when receiving a stereo broadcast).
Memorizing stations
You can save up to 30 station presets so that
you always have easy access to your favorite
stations without having to tune in manually
each time.
1 Tune to an AM or FM radio station.
For the FM band, select mono or auto-stereo
reception as necessary. This setting is saved
along with the preset.
2 Press
SETUP
and use
/
to choose
‘ST.MEM.’ then press
ENTER
.
3 Use
/
to select the station preset you
want then press
ENTER
.
Listening to station presets
1 Make sure the
TUNER
function is selected.
2 Use the
ST +/–
buttons to select a station
preset.
• You can also use the number buttons to do
this.
Listening to other sources
You can connect auxiliary sources (TV, satellite
receiver, etc.) to this unit for playback through
the speaker system. See Connecting auxiliary
audio components on page 29 for more on this.
• To connect a USB device to the USB
terminal, see USB playback on page 22.
1 Make sure that the external source (TV,
satellite receiver, etc.) is switched on.
2 Press
LINE
to select the source.
3 If necessary, start playback of the source.
AUDIO
STANDBY
/ON DVD/CD
TUNER
(FM/AM)
LINEUSB
OPEN/
CLOSE
Getting started 02
13
En
English FrançaisDeutsch
Nederlands
Italiano Español
Setting the sleep timer
The sleep timer switches off the system after
about an hour so you can fall asleep without
worrying about it. 1
• Press
SLEEP
repeatedly to select an option
then press
ENTER
.
Choose between the following options:
•SLP ON – Switches off after about an hour
•SLP OFF
– Cancels the sleep timer
After selecting SLP ON, you can press SLEEP
again to check how much time is left. Each line
indicates approximately 12 minutes
(remaining):
Dimming the display
You can dim the display if you find it too bright.
1 Press
SETUP
and use
/
to choose
DIMMER then press
ENTER
.
This is shown in the front panel display.
2 Use
/
to select LIGHT or DARK then
press
ENTER
.
Note
1 The display dims when the sleep timer is set.
S L P - - - - -
Listening to your system
14
En
Chapter 3
Listening to your system
Auto listening mode
The Auto listening mode is the simplest way to
listen to any source as it was mastered: the
output from the speakers mirrors the channels
in the source material.
• Press
SURROUND
to select the AUTO
listening mode.
1
Listening in surround sound
You can listen to stereo or multichannel
sources in surround sound. 2 Surround sound
is generated from stereo sources using one of
the Dolby Pro Logic decoding modes.
• Press
SURROUND
repeatedly to select a
listening mode.
1
The choices that appear in the display will vary
according to the type of source that’s playing.
• – Auto listening mode (see above)AUTO
• DOLBY PL (Dolby Pro Logic) – 4.1 channel
surround sound (use with any two-channel
source)
• (Dolby Pro Logic II Movie) – Pro MOVIE
Logic II 5.1 channel surround sound,
especially suited to movie sources (use
with any two-channel source)
• (Dolby Pro Logic II Music) – Pro MUSIC
Logic II 5.1 channel surround sound,
especially suited to music sources (use
with any two-channel source)
• – See belowSTEREO Listening in stereo
Using Front Surround
XV-DV151 only
The Front Surround mode is effective when
DVD/CD or USB is selected as the input source
and you are using the Front surround 3-spot
speaker setup as described in Home theater
sound setup Speaker Setup on page 9 and the
Guide.
• The surround speakers should be placed
on top of the front speakers and oriented
towards the walls.
1 Press
SETUP
and use
/
to choose
‘F.SURR’ then press
ENTER
.
3
2 Use
/
to select
MODE ON
or
MODE
OFF
then press
ENTER
.
4
After selecting , you can use the MODE ON
surround listening modes with Front Surround.
Note
1 If the source is Dolby Digital or DTS, the corresponding indicator lights in the front panel display.
2 Note that the input source must be switched to or for multichannel playback.DVD/CD USB
TEST TONE SOUND
SURROUND
TUNE
SETUP
TEST TONE SOUND
SURROUND
TUNE
SETUP
3 Note that the option does not appear when headphones are connected.F.SURR
4 When set to , make sure to follow the Setup Guide for best surround sound.MODE ON
TOP MENU
RETURN
TEST TONE SOUND
SURROUND
TUNE
TUNE
ENTER
MENU
STST
HOME
MENU
SETUP
Listening to your system 03
15
En
English FrançaisDeutsch
Nederlands
Italiano Español
Listening in stereo
You can listen to any source—stereo or
multichannel—in stereo. When playing a
multichannel source, all channels are
downmixed to the front left/right speakers and
the subwoofer.
• Press
SURROUND
repeatedly until
STEREO shows in the display.
Listening with headphones
When headphones are connected, only the
STEREO
mode is available.
Using the SFC modes
The SFC (Sound Field Control) modes can be
used with any multichannel or stereo source
for a variety of additional surround sound
effects.
1 Press
SOUND
.
2 Use
/
to select SFC MODE then press
ENTER
.
3 Press
/
then
ENTER
to select an SFC
Sound Mode.
Select between OFF, ACTION
, DRAMA,
ROCK, POP, HALL
or LIVE
.
Adjusting the bass and treble
Use the bass and treble controls to adjust the
overall tone.
1 Press
SOUND
.
2 Use
/
to select BASS or TREBLE then
press
ENTER
.
3 Use
/
to adjust the sound
then press
ENTER to confirm
.
Boosting the bass level
There are two bass modes you can use to
enhance the bass in a source.
1 Press
SOUND
.
2 Use
/
to select BASSMODE then press
ENTER
.
3 Use
/
to adjust the sound
then press
ENTER to confirm
.
Select between OFF, MUSIC
or CINEMA.
TEST TONE SOUND
SURROUND
TUNE
SETUP
TOP MENU
RETURN
TEST TONE SOUND
SURROUND
TUNE
TUNE
ENTER
SETUP
MENU
STST
HOME
MENU
Disc playback features
16
En
Chapter 4
Disc playback features
Important
• Many of the functions covered in this
chapter apply to DVD discs, Video CDs/
Super VCDs, CDs, DivX video and WMA/
MP3/MPEG-4 AAC/JPEG discs, although
the exact operation of some varies slightly
with the kind of disc loaded.
• Some DVDs restrict the use of some
functions (random or repeat, for example)
in some or all parts of the disc. This is not a
malfunction.
• When playing Video CD/Super VCDs, some
of the functions are not available during
PBC playback. If you want to use them,
start the disc playing using a number
button to select a track.
Scanning discs
You can fast-scan discs forward or backward at
various different speeds. 1
• During playback, press
or
to start
scanning.
Press repeatedly to increase the scanning
speed (shown on-screen).
• To resume playback, press (play).2
Playing in slow motion
You can play DVDs, Video CD/Super VCDs and
DivX video at four different forward slow
motion speeds. DVD discs can also be played
in reverse slow motion.
1 During playback, press
(pause).
2 Press and hold
/
or
/
until slow
motion playback starts.
Press repeatedly to change the slow motion
speed (shown on-screen).
• To resume playback, press (play).2
Frame advance/frame reverse
You can advance or back up DVD discs frame-
by-frame. With Video CD/Super VCDs and DivX
video you can only use frame advance.
1 During playback, press
(pause).
2 Press
/
or
/
to reverse or
advance a frame at a time.
• To resume playback, press (play).2
Playing a JPEG slideshow
After loading a disc containing JPEG pictures,
press to start a slideshow from the first
folder/picture on the disc. 3 The player displays
the pictures in each folder in alphabetical
order.
• If the disc contains WMA/MP3/MPEG-4
AAC files, playback of the slideshow and
audio files repeats. During audio playback,
you can still use the skip ( /), scan
(/) and pause ( ) functions.
Pictures are automatically adjusted so that
they fill as much of the screen as possible.
Note
1 Only one speed is available for DivX video discs.
2 • Depending on the disc, normal playback may automatically resume when a new chapter is reached on a DVD disc.
• With Video CD/Super VCDs in PBC mode or a WMA/MP3/MPEG-4 AAC track, playback automatically resumes at the end or
beginning of the track.
3 • The time it takes for the player to load a file increases with large file sizes.
• Discs can contain up to 299 folders and up to 648 folders and files combined.
Disc playback features 04
17
En
English FrançaisDeutsch
Nederlands
Italiano Español
While the slideshow is running:
Browsing DVD or Video CD/
Super VCD discs with the Disc
Navigator
Use the Disc Navigator to browse through the
contents of a DVD or Video CD/Super VCD disc
to find the part you want to play.
1 During playback, press HOME MENU
and select ‘Disc Navigator’ from the on-
screen menu.
2 Select a view option.
The options available depend on the kind of
disc loaded and whether the disc is playing or
not, but include:
•Title – Titles from a DVD-Video disc.
•Chapter – Chapters from the current title
of a DVD-Video disc.
•Track – Tracks from a Video CD/Super VCD
disc.
•Time – Thumbnails from a Video CD/Super
VCD disc at 10 minute intervals.
•Original: Title – Original titles from a VR
mode DVD-RW disc.
•Playlist: Title – Playlist titles from a VR
mode DVD-RW disc.
•Original: Time – Thumbnails from the
Original content at 10 minute intervals.
•Playlist: Time – Thumbnails from the
Playlist at 10 minute intervals.
The screen shows up to six moving thumbnail
images displayed one after another. To display
the previous/next six thumbnails, press /
.
3 Select the thumbnail image for what
you want to play.
You can use either /// and ENTER
to
select a thumbnail, or the number buttons.
To select using the number buttons, enter a
two-digit number then press ENTER.
Button What it does
Pauses the slideshow (or audio);
press again to restart.
Jumps to the previous picture (or
audio le with audio playback).
Jumps to the next picture (or
audio le with audio playback).
/// Pauses the slideshow and
rotates/ips the displayed
picture (press (play) to restart
slideshow).
ZOOM Pauses the slideshow and zooms
the picture. Press again to toggle
between 1x, 2x and 4x zoom
(press (play) to restart
slideshow).
MENU Displays the Disc Navigator
screen (see below).
Disc Navigator
Disc Navigator
Title
Chapter
01
04
02
05
03
06
Disc Navigator: Title
01- 49: - -
Disc playback features
18
En
Browsing WMA, MP3, MPEG-4
AAC, DivX video and JPEG files
with the Disc Navigator
Use the Disc Navigator to find a particular file
or folder by filename.
1 Press HOME MENU and select ‘Disc
Navigator’ from the on-screen menu.
2 Use /// and ENTER to navigate.
Use / to move up and down the folder/file
list.
Use to return to the parent folder. 1
Use ENTER
or to open a highlighted folder.
• When a JPEG file is highlighted, a
thumbnail image is displayed on the right.
3 To play the highlighted track or DivX
video file or display the highlighted JPEG
file, press ENTER.
• When a WMA/MP3/MPEG-4 AAC or DivX
video file is selected, playback begins from
that file, and continues until the end of the
folder.
• When a JPEG file is selected, a slideshow
begins, starting with that file, and
continues to the end of the folder.
Tip
• You can also play a JPEG slideshow while
listening to WMA/MP3/MPEG-4 AAC
playback. Simply select the audio file you
want to listen to followed by the JPEG from
which you want the slideshow to start.
Playback of both the slideshow and the
audio files repeats. Playback controls are
effective for the JPEG slideshow only.
• To play the contents of the whole disc
rather than just the current folder, exit the
Disc Navigator and start playback using
the (play) button.
Looping a section of a disc
The A-B Repeat function allows you to specify
two points (A and B) within a track (CD, Video
CD/Super Video CD) or title (DVD) that form a
loop which is played over and over.
1 During playback, press
HOME MENU
and
select ‘
Play Mode
’.
2 Select ‘A-B Repeat’.
3 Press
ENTER
on ‘A(Start Point)’ to set the
loop start point.
4 Press
ENTER
on ‘B(End Point)’ to set the
loop end point.
After pressing ENTER
, playback jumps back to
the start point and plays the loop.
5 To resume normal playback, select ‘Off’.
Using repeat play
In addition to various repeat play options, it’s
also possible to use repeat play together with
program play (see Creating a program list on
page 19).
Note
1 You can also do this by going to the ‘ .. ’ folder at the top, then pressing ENTER
.
00:00/ 00:00 0kbps
Folder1
Folder2
Folder3
Folder4
File1
File2
File3
File4
File5
Folder2
00:00/ 00:00 0kbps
Play Mode
Disc playback features 04
19
En
English FrançaisDeutsch
Nederlands
Italiano Español
1 During playback, press
HOME MENU
and
select ‘
Play Mode
’.
2 Select ‘Repeat’ then select a repeat play
option.
1
If program play is active, select Program
Repeat to repeat the program list, or Repeat
Off to cancel.
• For DVD discs, select Title Repeat or
Chapter Repeat .
• For CDs and Video CD/Super VCDs, select
Disc Repeat or Track Repeat.
• For DivX video discs, select Title Repeat
(or Repeat Off).
Using random play
Use this function to play titles or chapters
(DVD-Video) or tracks (CD and Video CD/Super
VCD) in a random order.2
1 During playback, press
HOME MENU
and
select ‘
Play Mode
’.
2 Select ‘Random’ then select an option.
• For DVD discs, select Random Title or
Random Chapter.
• For CDs and Video CD/Super VCDs, select
On or Off to switch random play on or off.
Tip
• Use the following controls during random
play:
• Random play remains in effect until you
select Random Off from the random play
menu options.
Creating a program list
This feature lets you program the play order of
titles/chapters/tracks on a disc.
3
1 During playback, press
HOME MENU
and
select ‘
Play Mode
’.
2 Select ‘Program’ then select ‘Create/Edit’
from the list of program options.
3 Use
///
and
ENTER
to select a
title, chapter or track for the current step in
the program list.
For a DVD disc, you can add a title or a chapter.
• For a CD or Video CD/Super VCD, select a
track to add to the program list.
After pressing
ENTER to select the title/
chapter/track, the step number automatically
moves down one.
4 Repeat step 3 to build up a program list.
A program list can contain up to 24 steps.
• You can insert steps by just highlighting
the position where you want the new step
to appear and entering a title/chapter/track
number.
• To delete a step, highlight it and press
CLEAR.
Note
1 You can’t use repeat play with WMA/MP3/MPEG-4 AAC discs.
2 • You can set the random play option when a disc is playing or stopped. However, you can't use random play together with
program play.
• You can’t use random play with VR format DVD-R/RW discs, WMA/MP3/MPEG-4 AAC discs, DivX video discs, or while a DVD
disc menu is being displayed.
Button What it does
Selects a new track/title/chapter
at random.
Returns to the beginning of the
current track/title/chapter;
further presses select another
random track/title/chapter.
3 You can’t use Program play with VR format DVD-R/RW discs, WMA/MP3/MPEG-4 AAC discs, DivX video discs, or while a DVD
disc menu is being displayed.
Button What it does
Disc playback features04
20
En
5 To play the program list, press
(play).
Program play remains active until you turn off
program play (see below), erase the program
list (see below), eject the disc or switch off.
Tip
• Use the following controls during program
play:
Other functions available from the
program menu
There are a number of other options in the
program menu in addition to Create/Edit.
•Playback Start – Starts playback of a
saved program list
•Playback Stop – Turns off program play,
but does not erase the program list
•Program Delete – Erases the program list
and turns off program play
Searching a disc
You can search DVD discs by title or chapter
number, or by time; CDs and Video CD/Super
VCDs by track number or time; DivX video discs
by time.
1 Press
HOME MENU
and select ‘
Play
Mode
’.
2 Select ‘Search Mode’.
The search options that appear depend on the
kind of disc loaded.
3 Select a search mode.
• The disc must be playing in order to use
time search.
4 Use the number buttons to enter a title,
chapter or track number, or a time.
• For a time search, enter the number of
minutes and seconds into the currently
playing title (DVD/ DivX video) or track (CD/
Video CD/Super VCD) you want playback to
resume from. For example, press
4, 5, 0, 0
to have playback start from 45 minutes into
the disc. For 1 hour, 20 minutes and 30
seconds, press
8,
0, 3, 0.
5 Press
ENTER
to start playback.
Switching subtitles
Some DVD discs and DivX video discs have
subtitles in one or more languages; the disc
box will usually tell you which subtitle
languages are available. You can switch
subtitle language during playback.
1
• Press
SUBTITLE
repeatedly to select a
subtitle option.
• To set subtitle preferences, see Language
settings on page 25.
• See Displaying DivX subtitle files on
page 32 for more on DivX subtitles.
Switching language / audio
channels
When playing discs recorded with dialog in two
or more languages, or with dual-mono audio2
you can switch these during playback.3
• Press
AUDIO
repeatedly to select an
audio language option.
• To set audio language preferences, see
Language settings on page 25.
Button What it does
HOME
MENU
Save the program list and exit
without starting playback.
Skip to the next step in the
program list.
Note
1 Some discs only allow you to change subtitle language from the disc menu. Press TOP MENU or
MENU to access.
2 Some Super VCDs have two soundtracks. With these discs you can switch between the two soundtracks as well as individual
channels in each.
3 Some discs only allow you to change audio language from the disc menu. Press TOP MENU or
MENU to access.
USB playback05
22
En
Chapter 5
USB playback
Using the USB interface
It is possible to listen to two-channel audio1
and watch JPEG files using the USB interface
on the front of this unit. Connect a USB mass
storage device2 as shown below.
1 With the player switched on, press USB.
Make sure your TV is on and set to the correct
video input.
2 Connect your USB device.
The USB terminal is located on the front panel.
3 Press
(play) to start playback.
If your USB device contains JPEGs, a
slideshow will start. See Playing a JPEG
slideshow on page 23 for more on this.
• Make sure USB DATA is showing in the
front panel display (or the system is in
standby) when disconnecting.
Important
If a USB ERR message lights in the display, it
may mean that the power requirements of the
USB device are too high for this player, or that
the device is incompatible. Try the following:
• Switch the player off, then on again.
• Reconnecting the USB device with the
player switched off.
• Selecting to another input source (like
DVD/CD ), then back to
USB.
• Using a dedicated AC adapter (supplied
with the device) for USB power.
If this doesn’t remedy the problem, it is likely
your USB device is incompatible.
Basic playback controls
The following table shows the basic controls on
the remote for USB playback.
Note
1 This includes playback of WMA/MP3/MPEG-4 AAC files (except files with copy-protection or restricted playback). It is not pos-
sible to play DivX files through the USB terminal.
2 • Compatible USB devices include external magnetic hard drives, portable flash memory (particularly keydrives) and digital
audio players (MP3 players) of format FAT16/32. It is not possible to connect this unit to a personal computer for USB playback.
• Pioneer cannot guarantee compatibility (operation and/or bus power) with all USB mass storage devices and assumes no
responsibility for any loss of data that may occur when connected to this unit.
• With large amounts of data, it may take longer for the system to read the contents of a USB device.
USB mass
storage device
USB
Type A
Button What it does
Starts normal playback.
Pauses/unpauses playback.
Stops playback.
Press to start fast reverse scanning.
Press to start fast forward scanning.
Skips to the start of the current file,
then previous files.
Skips to the next file.
USB playback 05
23
En
English FrançaisDeutsch
Nederlands
Italiano Español
Scanning files
You can fast-scan forward or backward at
various different speeds.
• During playback, press
or
to start
scanning.
Press repeatedly to increase the scanning
speed (shown on-screen).
• To resume playback, press (play).1
Playing a JPEG slideshow
Press to start a slideshow from the first
folder/picture.2 The pictures in each folder are
displayed in order.
• If the device contains WMA/MP3/MPEG-4
AAC files, playback of the slideshow and
audio files repeats. During audio playback,
you can still use the skip (/), scan
(/) and pause () functions.
Pictures are automatically adjusted so that
they fill as much of the screen as possible.
While the slideshow is running:
Browsing files with the
Navigator
Use the Navigator to find WMA, MP3, MPEG-4
AAC and JPEG files or folders by name.3
1 Press MENU.
2 Use /// and ENTER to navigate.
Use / to move up/down the folder/file list.
Use to return to the parent folder.4
Use ENTER or to open a highlighted folder.
• When a JPEG file is highlighted, a
thumbnail image is displayed on the right.
3 To play the highlighted track or display
the highlighted JPEG file, press ENTER.
• When a WMA/MP3/MPEG-4 AAC file is
selected, playback begins from that file,
and continues until the end of the folder.
• When a JPEG file is selected, a slideshow
begins, starting with that file, and
continues to the end of the folder.
Tip
• You can also play a JPEG slideshow while
listening to WMA/MP3/MPEG-4 AAC
playback. Simply select the audio file you
want to listen to followed by the JPEG from
which you want the slideshow to start.
Playback of both the slideshow and the
audio files repeats. Playback controls are
effective for the JPEG slideshow only.
• To play all of the contents, rather than just
the current folder, exit the Navigator and
start playback using the (play) button.
Note
1 With WMA/MP3/MPEG-4 AAC tracks, playback automatically resumes at the end or beginning of the track.
2 • The time it takes for the player to load a file increases with large file sizes.
• USB devices can contain up to 299 folders and up to 648 folders and files combined.
Button What it does
Pauses the slideshow (or audio);
press again to restart.
Jumps to the previous picture (or
audio file with audio playback).
Jumps to the next picture (or
audio file with audio playback).
/// Pauses the slideshow and
rotates/flips the current picture.
(press to restart slideshow).
ZOOM Pauses the slideshow and zooms
the picture. Press again to toggle
between 1x, 2x and 4x zoom.
(press to restart slideshow).
MENU Displays the Navigator screen
(see below).
3 Filenames may be displayed incorrectly with some digital audio players.
4 You can also do this by going to the ‘ ..’ folder at the top, then pressing ENTER.
Button What it does
Audio Settings and Video Adjust menus06
24
En
Chapter 6
Audio Settings and Video
Adjust menus
Audio Settings menu
The Audio Settings menu offers features for
adjusting the way discs sound.
1 Press
HOME MENU
and select ‘Audio
Settings’ from the on-screen display.
2 Select and change settings using
///
and
ENTER
.
Audio DRC
• Settings: High, Medium, Low,
Off (default)
When watching Dolby Digital DVDs at low
volume, it’s easy to lose the quieter sounds
completely—including some of the dialog.
Switching Audio DRC (Dynamic Range
Control) to on can help by bringing up the
quieter sounds, while controlling loud peaks.
How much of a difference you hear depends on
the material you’re listening to. If the material
doesn’t have wide variations in volume, you
may not notice much change.
1
Video Adjust menu
From the Video Adjust screen you can adjust
settings that affect picture presentation.
1 Press
HOME MENU
and select ‘Video
Adjust’ from the on-screen display.
2 Make settings using
///
and
ENTER
.
You can adjust the following settings:
•Sharpness – Adjusts the sharpness of
edges in the picture (Fine, Standard ,
Soft)
•Brightness – Adjusts the overall
brightness (–20 to
+20)
•Contrast – Adjusts the contrast between
light and dark (–16
to +16)
•Gamma – Adjusts the ‘warmth’ of the
picture (High, Medium, Low, Off)
•Hue – Adjusts the red/green balance
(Green 9 to Red 9)
•Chroma Level – Adjusts how saturated
colors appear (–9 to +9)
Adjust the Brightness, Contrast, Hue and
Chroma Level settings using /.
3 Press
ENTER
to return to the Video Adjust
screen, or
HOME MENU
to exit.
Note
1 Audio DRC is only effective with Dolby Digital audio sources.
Audio Settings
Audio Settings
Audio DRC High
Medium
Low
Off
Video Adjust
Sharpness
Brightness
Contrast
Gamma
Hue
Chroma Level
Standard
0
0
Off
0
0
Video Adjust
Brightness min max 0
Initial Settings menu 07
25
En
English FrançaisDeutsch
Nederlands
Italiano Español
Chapter 7
Initial Settings menu
Using the Initial Settings menu
The Initial Settings menu provides audio and
video output settings, parental lock settings,
and display settings, among others.
If an option is grayed out it means that it
cannot be changed at the current time. This is
usually because a disc is playing. Stop the
disc, then change the setting.
1 Press
DVD/CD
.
2 With playback stopped, press
HOME
MENU
and select ‘Initial Settings’.
3 Use
///
and
ENTER
to select the
setting and option you want to set.
All the settings and options are explained on
the following pages.1
Video Output settings
Language settings
Note
1 • In the table, the default setting is shown in bold: other settings are shown in italics.
• Some settings, such as TV Screen, Audio Language and Subtitle Language may be overridden by the DVD disc. Often
these settings can also be made from the DVD disc menu.
Initial Settings
Setting Option What it means
TV Screen
(See also Screen sizes
and disc formats on
page 35.)
4:3 (Letter Box) Set if you have a conventional 4:3 TV. Widescreen movies are
shown with black bars top and bottom.
4:3 (Pan & Scan) Set if you have a conventional 4:3 TV. Widescreen movies are
shown with the sides cropped so that the image fills the screen.
16:9 (Wide) Set if you have a widescreen TV.
Component Out
(See also Connecting
using the component
video output on
page 30.)
Interlace Set if your TV is not compatible with progressive scan video.
Progressive Set if your TV is compatible with progressive scan video (see
your TV’s instruction manual for details). Press ENTER once
more to confirm (or RETURN to cancel).
Note that progressive scan video is only output from the
component video jacks.
Setting Option What it means
Audio Language English (all other models) /
Chinese
(Taiwanese model)
If there is the specified language soundtrack on the disc, it is
played.
Languages as displayed If there is a language selected on the disc, it is played.
Other Language Select to choose a language other than the ones displayed (see
Using the language code list on page 39).
Initial Settings menu07
26
En
Display settings
Options settings
Speakers settings
Parental Lock
• Default level: Off; Default password: none;
Default Country/Area code: us (2119)
Subtitle Language English (all other models) /
Chinese
(Taiwanese model)
If there are subtitles in the specified language on the disc they
are displayed.
Languages as displayed The subtitle language selected on the disc is displayed.
Other Language Select to choose a language other than the ones displayed (see
Using the language code list on page 39).
DVD Menu
Language
w/Subtitle Lang. DVD disc menus are displayed in the same language as your
selected subtitle language, if possible.
Languages as displayed DVD menus are displayed in the selected language, if possible.
Other Language Select to choose a language other than the ones displayed (see
Using the language code list on page 39).
Subtitle Display On Subtitles are displayed in your selected subtitle language.
Off Subtitles are always off by default when you play a DVD disc.
Setting Option What it means
OSD Language English(all other models) /
(Taiwanese model)
On-screen displays are shown in the language specified.
Languages as displayed On-screen displays are shown in the language selected.
Angle Indicator On A camera icon is displayed on-screen during multi-angle
scenes on a DVD disc.
Off No multi-angle indication is shown.
Setting Option What it means
Parental Lock – See Parental Lock below.
DivX(R) VOD Display See About DivX® VOD content below.
Setting Option What it means
Speaker Distance – Specify the distance of your speakers from your listening
position (see Speaker Distance on page 28).
Setting Option What it means
Initial Settings menu 07
27
En
English FrançaisDeutsch
Nederlands
Italiano Español
To give you some control over what your
children watch on your DVD player, some DVD-
Video discs feature a Parental Lock level. If
your player is set to a lower level than the disc,
the disc won’t play.
Some discs also support the Country/Area
Code feature. The player does not play certain
scenes on these discs, depending on the
Country/Area Code you set.
Registering a new password
Register a password to change the Parental
Lock level or enter a Country/Area code.1
1 Select ‘Password’.
2 Use the number buttons to input a 4-digit
password then press
ENTER
.
Changing your password
To change your password, confirm your
existing password then enter a new one.
1 Select ‘Password Change’, input your
existing password, then press
ENTER
.
2 Enter a new password and press
ENTER
.
Setting/changing the Parental Lock
1 Select ‘Level Change’.
2 Use number buttons to enter your
password, then press
ENTER
.
3 Select a new level and press
ENTER
.
• Press repeatedly to lock more levels
(more discs will require the password);
press to unlock levels. You can’t lock
level 1.
Setting/changing the Country/Area code
You can find the Country/Area code list on
page 40.
1 Select ‘Country Code’, input your
password, then press
ENTER
.
2 Select a Country/Area code then press
ENTER
.
There are two ways you can do this:
• Select by code letter: Use / to change
the Country/Area code.
• Select by code number: Press
then use
the number buttons to enter the 4-digit
Country/Area code.
The new Country/Area code takes effect after
ejecting the disc once.
About DivX
®
VOD content
In order to play DivX VOD (video on demand)
content on this player, you first need to register
the player with your DivX VOD content
provider. You do this by generating a DivX VOD
registration code, which you submit to your
provider.2
Important
• DivX VOD content is protected by a DRM
(Digital Rights Management) system. This
restricts playback of content to specific,
registered devices.
• If you load a disc that contains DivX VOD
content not authorized for your player, the
message
Authorization Error is displayed
and the content will not play.
Note
1 • Not all discs use Parental Lock, and will play without requiring the password first.
• If you forget your password, you’ll need to reset the player to register a new password (see Resetting the system on page 39).
Video Output
Language
Display
Options
Speakers
Parental Lock
DivX (R) VOD
Password
Level Change
Country Code
Initial Settings
2 Resetting the player (as described in Resetting the system on page 39) will not cause you to lose your registration code.
Initial Settings menu07
28
En
Displaying your DivX VOD registration
code
1 Press HOME MENU and select ‘Initial
Settings’.
2 Select ‘Options’, then ‘DivX (R) VOD’.
3 Select ‘Display’.
Your 8-digit registration code is displayed.
Make a note of the code as you will need it
when you register with a DivX VOD provider.
Playing DivX
®
VOD content
Some DivX VOD content may only be playable
a fixed number of times. When you load a disc
containing this type of DivX VOD content, the
remaining number of plays is shown on-screen
and you then have the option of playing the
disc (thereby using up one of the remaining
plays), or stopping. If you load a disc that
contains expired DivX VOD content (for
example, content that has zero remaining
plays), the message Rental Expired is
displayed.
If your DivX VOD content allows an unlimited
number of plays, then you may load the disc
into your player and play the content as often
as you like, and no message will be displayed.
Speaker Distance
• Default setting: 3.0 m
To get the best surround sound from your
system, you should set up the speakers equal
distances from your listening position.
1 Press HOME MENU and select ‘Initial
Settings’.
2 Select ‘
Speaker
s’, then ‘Speaker
Distance’.
3 Use
/
to select a speaker.
4 Press
to change the speaker distance
for the highlighted speaker.
5 Use
/
to change the distance.
• When you change the distance settings of
the front left (L) or front right (R) speakers,
all the other speaker distances change
relative to it.
• Front left/right (L/R) speaker distances can
be set from 30 cm to 9 m in 30 cm incre-
ments.1
• The center speaker (C) can be set from –2.1
m to 0 m relative to the front left/right
speakers.
• Surround left/right (SL/SR) speakers can
be set from –6.0 m to 0 m relative to the
front left/right speakers.2
• The subwoofer (SW) can be set from –2.1 m
to 0 m relative to the front left/right
speakers.
6 Press
to go back to the speaker list if
you want to modify another speaker, or press
ENTER
to exit the Speaker Distance screen.
Video Output
Language
Display
Options
Speakers
Display
Initial Settings
Parental Lock
DivX (R) VOD
Note
1 The L and
R speakers are paired; you can’t set them differently.
2XV-DV151 only – Make sure to set them the same distance when using Front Surround (page 14).
Video Output
Language
Display
Options
Speakers
Speaker Distance
Initial Settings
Video Output
Language
Display
Options
Speakers
L
C
R
SR
SL
SW
3.0m
3.0m
3.0m
3.0m
3.0m
3.0m
Initial Settings
Other connections 08
29
En
English FrançaisDeutsch
Nederlands
Italiano Español
Chapter 8
Other connections
Connecting external antennas
For an external AM antenna, use 5 m to 6 m of
vinyl-insulated wire and set up either indoors or
outdoors. Leave the loop antenna connected.
For an external FM antenna, use a PAL
connector to hook up an external FM antenna.
Connecting auxiliary audio
components
Using the stereo analog inputs, you can
connect an external component such as a tape
deck or MD player for playback through this
system.
• Connect the AUDIO IN jacks to the analog
outputs of an external playback component.
Connect using RCA pin-plug stereo cables.
• These jacks are labeled LINE on the rear
panel.
Connecting the S-video output
If your TV has an S-video input, you can use this
instead of the standard video output for a
better quality picture.
• Use an S-video cable to connect the
S-
VIDEO OUT
to an S-video input on your TV.
Line up the small triangle above the jack with
the same mark on the plug before plugging in.
Outdoor antenna
5 m to 6 m
Indoor
antenna
(vinyl-coated
wire)
AM LOOP
ANTENNA
PAL connector
R
L
R L
FRONT CENTER
SURROUND
SUB
WOOFER
R L
O
COMPONENT
VIDEO
C
R
/
P
R
C
B
/
P
B
Y
AUDIO IN
LINE
SPEAKERS
VIDEO OUT
AUDIO
OUTPUT
Tape deck, etc.
XV-DV151/252
R
L
FRONT
SURROUND
S-VIDEO
VIDEO
COMPONENT
VIDEO
C
R
/
P
R
C
B
/
P
B
Y
AUDIO IN
LINE
VIDEO OUT
TV
S-VIDEO
INPUT
XV-DV151/252
Other connections08
30
En
Connecting using the
component video output
If your TV has component video inputs, you can
use these instead of the standard video output
to connect this system to your TV.1 This should
give you the best quality picture from the three
types of video output available.
• Use a component video cable to connect
the
COMPONENT VIDEO OUT
to a set of
component inputs on your TV.
About progressive scan video
Compared to interlace video, progressive scan
video effectively doubles the scanning rate of
the picture, resulting in a very stable, flicker-
free image. Progressive scan video is available
only from the component video output.
Compatibility of this player with
progressive-scan and high-definition TVs.
This player is compatible with progressive
video Macro Vision System Copy Guard.2
Note
1 The component video output is switchable between interlaced and progressive formats. See Video Output settings on page 25.
2 Consumers should note that not all high-definition television sets are fully compatible with this product and may cause arti-
facts to be displayed in the picture. In case of 525 progressive scan picture problems, it is recommended that the user switch
the connection to the ‘standard definition’ output (Interlace). If there are questions regarding our TV set compatibility with this
model, please contact our customer service center.
Ω
R
L
S-VIDEO
VIDEO
COMPONENT
VIDEO
C
R
/
P
R
C
B
/
P
B
Y
VIDEO OUT AUDIO IN
LINE
TV
COMPONENT
INPUT
XV-DV151/252
Additional information 09
31
En
English FrançaisDeutsch
Nederlands
Italiano Español
Chapter 9
Additional information
Disc / content format playback
compatibility
This player is compatible with a wide range of
disc types (media) and formats. Playable discs
will generally feature one of the following logos
on the disc and/or disc packaging. Note
however that some disc types, such as
recordable CD and DVD, may be in an
unplayable format.
See the Disc compatibility table below for more
information.
• This unit will play DVD+R/+RW discs.
• is a trademark of Fuji Photo Film Co. Ltd.
• is a trademark of DVD Format/Logo
Licensing Corporation.
• Also compatible with KODAK Picture CD.
This player supports the IEC’s Super VCD stan-
dard for superior picture quality, dual
soundtracks, and widescreen support.
About DualDisc playback
A DualDisc is a new two -sided disc, one side
of which contains DVD content video, audio,
etc. while the other side contains non-DVD
content such as digital audio material.
The non-DVD, audio side of the disc is not
compliant with the CD Audio specification and
therefore may not play.
The DVD side of a DualDisc plays in this
product. DVD-Audio content will not play.
For more detailed information on the DualDisc
specification, please refer to the disc
manufacturer or disc retailer.
Disc compatibility table
DVD-Video DVD-R DVD-RW
Video CD
Fujicolor CD
Audio CD CD-R CD-RW
VIDEO
CD
Super Video CD (Super VCD)
Media Compatible formats
CD-R/RW
• CD-Audio, Video CD/Super VCD, ISO
9660 CD-ROM*
* ISO 9660 Level 1 or 2 compliant. CD
physical format: Mode1, Mode2 XA
Form1. Romeo and Joliet file systems
are both compatible.
• Multi-session playback: No
• Unfinalized disc playback: No
DVD-R/RW
• DVD-Video (Video mode), Video
Recording (VR)*, UDF Bridge DVD-ROM
* Edit points may not play exactly as
edited; screen may go momentarily
blank at edited points.
• Multi Border playback: No
• Unfinalized playback: No
PC-created
disc
• Discs recorded using a PC may not
be playable due to the setting of the
software used to create the disc. In
these instances, check the DVD-R/RW
or CD-R/RW software manual or disc
boxes for more on compatibility.
• Discs recorded in packet write mode
are not compatible.
Additional information09
32
En
About DVD+R/DVD+RW compatibility
Only DVD+R/DVD+RW discs recorded in
‘Video Mode (DVD Video Mode)’ which have
been finalized, can be played back. However,
some editing made during the recording may
not be played back accurately.
About DivX
DivX is a compressed digital video format
created by the DivX® video codec from DivX,
Inc. This player can play DivX video files burned
on CD-R/RW and DVD-R/RW/ROM discs.
Keeping the same terminology as DVD-Video,
individual DivX video files are called ‘Titles’.
When naming files/titles on a CD-R/RW or
DVD-R/RW disc prior to burning, keep in mind
that by default they will play in alphabetical
order.
DivX video compatibility
• Official DivX® Certified product.
• Plays all versions of DivX® video (including
DivX®6) with standard playback of DivX®
media files.1
• File extensions: .avi and .divx (these must
be used for the player to recognize DivX
video files). Note that all files with the .avi
extension are recognized as MPEG4, but not
all of these are necessarily DivX video files
and therefore may not be playable on this
player.
Displaying DivX subtitle files
The font sets listed below are available for DivX
external subtitle files. You can see the proper
font set on-screen by setting the Subtitle
Language (in Language settings on page 25)
to match the subtitle file.2
Group 1: Albanian (sq), Basque (eu), Catalan (ca),
Danish (da), Dutch (nl), English (en), Faroese (fo),
Finnish (fi), French (fr), German (de), Icelandic (is), Irish
(ga), Italian (it), Norwegian (no), Portuguese (pt), Rhaeto-
Romanic (rm), Scottish (gd), Spanish (es), Swedish (sv)
Group 2: Albanian (sq), Croatian (hr), Czech (cs),
Hungarian (hu), Polish (pl), Romanian (ro), Slovak (sk),
Slovenian (sl)
Compressed
audio
• MPEG-1 Audio Layer 3 (MP3),
Windows Media Audio (WMA), MPEG-
4 AAC
• Sampling rates: 32 kHz / 44.1 kHz /
48 kHz
• Bit-rates: Any (128 kbps or higher
recommended)
• VBR (variable bit rate) MP3/WMA/
MPEG-4 AAC playback: No
• WMA lossless encoding: No
• DRM (Digital Rights Management)
compatible: Yes (DRM-protected audio
files will not play in this player).
• File extensions: .mp3, .wma, .m4a
(these must be used for the player to
recognize MP3/WMA/MPEG-4 AAC
files)
• File structure (may differ): Up to 299
folders on a disc; up to 648 folders and
files (combined) within each folder
JPEG file
• Baseline JPEG and EXIF 2.2* still
image files up to a resolution of 3072 x
2048.
*File format for digital still cameras
• Progressive JPEG compatible: No
• File extensions: .jpg (must be used
for the player to recognize JPEG files)
• File structure (may differ): Up to 299
folders on a disc; up to 648 folders and
files (combined) within each folder
Media Compatible formats
Note
1 Playback of .avi video files larger than 4 GB is not possible.
2 • For external subtitle files the following subtitle format filename extensions are supported (please note that these files are not
shown within the disc navigation menu): .srt, .sub, .ssa, .smi
• Some external subtitle files may be displayed incorrectly or not at all.
• The filename of the movie file has to be repeated at the beginning of the filename for the external subtitle file.
• The number of external subtitle files which can be switched for the same movie file is limited to a maximum of 10.
Additional information 09
33
En
English FrançaisDeutsch
Nederlands
Italiano Español
Group 3: Bulgarian (bg), Byelorussian (be), Macedonian
(mk), Russian (ru), Serbian (sr), Ukrainian (uk)
Group 4: Hebrew (iw), Yiddish (ji)
Group 5: Turkish (tr)
DivX, DivX Certified, and associated logos are
trademarks of DivX, Inc. and are used under
license.
About MPEG-4 AAC
Advanced Audio Coding (AAC) is at the core of
the MPEG-4 AAC standard, which incorporates
MPEG-2 AAC, forming the basis of the MPEG-4
audio compression technology. The file format
and extension used depend on the application
used to encode the AAC file. This unit plays
back AAC files encoded by iTunes® bearing the
extension '.m4a'. DRM-protected files will not
play, and files encoded with some versions of
iTunes® may not play, or filenames may display
incorrectly.
Apple and iTunes are trademarks of Apple Computer,
Inc., registered in the U.S. and other countries.
About WMA
The Windows Media® logo printed on the box
indicates that this player can playback
Windows Media Audio content.
WMA is an acronym for Windows Media Audio
and refers to an audio compression technology
developed by Microsoft Corporation. WMA
content can be encoded by using Windows
Media® Player version 7, 7.1, Windows Media®
Player for Windows® XP, or Windows Media®
Player 9 Series.
Microsoft, Windows Media, and the Windows logo are
trademarks, or registered trademarks of Microsoft
Corporation in the United States and/or other countries.
Using and taking care of discs
Handling discs
Hold the disc by its edges when handling so as
not to leave fingerprints, dirt or scratches on
either side of the disc. Damaged or dirty discs
can affect playback performance.
If a disc becomes marked with fingerprints,
dust, etc., clean using a soft, dry cloth.
Wipe lightly from the center of the disc using
straight strokes. Don’t wipe the disc surface
with circular strokes.
If necessary, use a cloth soaked in alcohol, or a
commercially available CD/DVD cleaning kit to
clean a disc more thoroughly. Never use
benzine, thinner or other cleaning agents such
as those designed for cleaning vinyl records.
Storing discs
Avoid leaving discs in excessively cold, humid,
or hot environments (including under direct
sunlight). Don't glue paper or put stickers onto
the disc, or use a pencil, ball-point pen or other
sharp-tipped writing instrument. These could
all damage the disc.
Discs to avoid
Discs spin at high speed inside the player. If a
disc is cracked, chipped, warped, or otherwise
damaged, don't risk using it in your player—
you could end up damaging the unit.
This unit is designed for use with conventional,
fully circular discs only. Pioneer disclaims all
liability arising in connection with the use of
shaped discs.
Additional information09
34
En
DVD Video regions
All DVD Video discs carry a region mark that
indicates which region(s) of the world the disc
is compatible with. Your DVD system also has
a region mark (on the rear panel). Discs from
incompatible regions will not play in this
player. In this instance, the following message
appears on-screen:
Incompatible disc region number
Can’t play disc
Discs marked ALL play in any player.
Installation and maintenance
Hints on installation
We want you to enjoy using this system for
years to come, so please bear in mind the
following points when choosing a location:
Do...
Use in a well-ventilated room.
Place on a solid, flat, level surface, such as a
table, shelf or stereo rack
.
Don’t...
Use in a place exposed to high temperatures or
humidity, including near radiators and other
heat-generating appliances.
Place on a window sill or other place where the
system will be exposed to direct sunlight.
Use in an excessively dusty or damp
environment.
Place directly on top of an amplifier, or other
component in your stereo system that becomes
hot in use.
Use near a television or monitor as you may
experience interference—especially if the
television uses an indoor antenna.
Use in a kitchen or other room where the system
may be exposed to smoke or steam.
Use on a thick rug or carpet, or cover with
cloth—this may prevent proper cooling of the
system unit.
Place on an unstable surface, or one that is not
large enough to support all four of the system
unit’s feet.
Cleaning the pickup lens
The DVD player’s lens should not become dirty
in normal use, but if for some reason it should
malfunction due to dust or dirt, consult your
nearest Pioneer authorized service center.
Although lens cleaners are commercially
available, we do not recommend using them
since some may damage the lens.
Problems with condensation
Condensation may form inside the player if it is
brought into a warm room from outside, or if
the temperature of the room rises quickly.
Although the condensation won’t damage the
player, it may temporarily impair performance.
Leave it to adjust to the warmer temperature
for about an hour before switching on.
Moving the system unit
If you need to move the main unit, first remove
a disc if there’s one in the player, then press
STANDBY/ON on the front panel to turn the
system off. Wait for GOOD BYE to disappear
from the display, then unplug the power cord.
1
Never lift or move the unit during playback—
discs rotate at high speeds and may damage.
Note
1 Unplugging the unit before GOOD BYE disappears from the display may cause the system to return to the factory settings.
Additional information 09
35
En
English FrançaisDeutsch
Nederlands
Italiano Español
Screen sizes and disc formats
DVD-Video discs come in different screen
aspects, ranging from TV programs, which are
generally 4:3, to CinemaScope widescreen
movies1, with an aspect ratio of up to about 7:3.
Televisions also come in different aspect
ratios; ‘standard’ 4:3 and widescreen 16:9.
2
TV system setting
Not applicable to the Taiwanese model
The default setting of this system is
AUTO, and
unless you notice that the picture is distorted
when playing some discs, you should leave it
set to AUTO. If you find picture distortion with
some discs, set the TV system to match your
country or region’s system. However, this may
restrict the kinds of disc you can watch. See
the table for the kinds of discs compatible with
each setting (AUTO, PAL and NTSC).3
1 Switch the unit into standby, then press
SETUP
.
2 Use
/
to choose TV SYS then press
ENTER
.
The TV system changes as follows:
•AUTO NTSC
•NTSC PAL
•PAL AUTO
The system automatically switches on and
you’ll see the new TV system setting in the
display after seeing WELCOME.4
Frequency step setting
If you find that you can’t tune into stations
successfully, the frequency step may not be
suitable for your country/region.
1 Switch the unit into standby, then press
SETUP
.
2 Use
/
to choose AM 9K/10K then
press
ENTER
.
3 Use
/
to select AM 9K or AM 10K then
press
ENTER
.
Note
1 Many widescreen discs override the system’s settings so that the disc is shown in letterbox format regardless of the setting.
Set to 4:3 (Letter Box), widescreen
discs are shown with black bars top
and bottom.
Set to 4:3 (Pan&Scan) , widescreen
discs are shown with the left and right
sides cropped. Although the picture
looks larger, you don’t actually see
the whole picture.
2 • Using the 16:9 (Wide) setting with a standard 4:3 TV, or one of the 4:3 settings with a widescreen TV, will result in distortion.
• When you watch discs recorded in 4:3 format, you can use the TV controls to select how the picture is presented. Your TV
may offer various zoom and stretch options; see the instructions that came with your TV for details.
• Some movie aspect ratios are wider than 16:9, so even with a widescreen TV, these discs will still play in a ‘letterbox’ style.
3 Most models of the newly developed countdown PAL TV system detect 50 Hz (PAL)/60 Hz (NTSC) and automatically switch
vertical amplitude, resulting in a display without vertical shrinkage. However, in some cases, the image may appear without col-
or. If your PAL TV does not have a V-Hold control, you may not be able to watch NTSC discs because of picture roll. If the TV has
a V-Hold control, adjust it until the picture stops rolling. On some TVs, the picture may shrink vertically, leaving black bands at
the top and bottom of the screen.
Player setting
Media Type Format NTSC PAL AUTO
DVD/Super VCD/
Video CD/DivX
Video
NTSC NTSC PAL NTSC
PAL NTSC PAL PAL
CD/MP3/WMA/
MPEG-4 AAC/
JPEG/no disc
—NTSC PAL NTSC or
PAL
4 You have to switch the player into standby (press STANDBY/ON) before each change.
Additional information
36
En
Troubleshooting
Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is
something wrong with this component, check the points below. Sometimes the trouble may lie in
another component. Investigate the other components and electrical appliances being used. If the
trouble cannot be rectified even after exercising the checks listed below, ask your nearest Pioneer
authorized service center or your dealer to carry out repair work.
• If the system does not operate normally due to external effects such as static electricity
disconnect the plug from the outlet and insert again to return to normal operating conditions.
General
Problem Remedy
The power does not turn
on, or switches off
suddenly (an error
message may be
displayed at startup).
• Wait for one minute before switching back on.
• Make sure there are no loose strands of wire touching the unit. This could cause
the system to shut off automatically.
• Check that the speakers are connected correctly.
• Make sure the voltage of the mains power source is correct for the model.
• Try reducing the volume level.
• If the problem persists, take it to your nearest Pioneer authorized service center
or your dealer for servicing.
No sound is output
when a function is
selected.
• If you’re using the line input, make sure the component is connected correctly
(see Connecting auxiliary audio components on page 29).
• Press MUTE on the remote control to turn muting off.
No sound from surround
or center speakers.
• Refer to Setting the channel levels on page 9 to check the speaker levels.
• When TUNER or LINE
is selected, you can only hear the source in stereo. Switch
the input source to DVD/CD or USB for multichannel sound.
• Check that you haven’t selected the STEREO
mode (see Listening in surround
sound on page 14).
• Connect the speakers properly (refer to the Setup Guide).
Can’t operate the remote
control.
• Replace the batteries (refer to the Setup Guide).
• Operate within 7 m, 30° of the remote sensor (refer to the Setup Guide).
• Remove any obstacles or operate from another position.
• Avoid exposing the remote sensor on the front panel to direct light.
TRAYLOCK
shows in the
display and the tray can’t
be ejected.
• Press and hold (eject) on the front panel for about eight seconds. Then the tray
can be opened/closed using (eject).
SND. DEMO shows in
the display and the unit
can’t be controlled.
• Press and hold (stop) on the front panel for about five seconds. The disc tray
ejects automatically to indicate the Sound Demo mode is disabled.
Additional information 09
37
En
English FrançaisDeutsch
Nederlands
Italiano Español
DVD/CD/Video CD player
Problem Remedy
The disc is ejected
automatically after
loading.
• Clean the disc and align the disc properly in the disc guide.
• If the region number on a DVD-video disc does not match the number on the
player, the disc cannot be used (see DVD Video regions
on page 34). In this
instance, the following message appears on screen: Incompatible disc region
number / Can’t play disc .
• Allow time for any condensation inside the player to evaporate. Avoid using the
player near an air-conditioning unit.
Playback not possible. • If the disc is loaded upside down, reload the disc with label side face up.
Picture playback stops
and buttons cannot be
used.
• Press (stop), then (play) to start playback again.
• Switch the power off once, then on again using the front panel
STANDBY/ON button.
Settings are canceled. • When the power is cut, settings will be canceled.
No picture/No color. • Check that connections are correct and that plugs are inserted fully.
• Check the manual of the TV/monitor to make sure the settings are correct.
• If the Progressive setting is selected and you have used component video cables
to connect a TV that is not compatible with a progressive scan signal, you will not
be able to see any picture at all. With your TV connected using either the
composite or S-video terminals, change the Component Out setting to Interlace
(see Video Output settings on page 25).
Screen is stretched or
aspect doesn’t change.
• The TV Screen setting is incorrect. Set the TV Screen option to match the TV/
monitor you're using (see Video Output settings on page 25).
When recorded on a
VCR or passed through
an AV selector, there is
disturbance in the
playback picture.
• This system uses copy-protection technology which may prevent recording or
cause picture problems when connected through a VCR or AV selector. This is not
a malfunction.
Picture disturbance
during playback or dark.
• This player is compatible with Macro-Vision System copy guard. Some discs
include a copy prevention signal, and when this type of disc is played back, stripes
etc., may appear on some sections of the picture depending on the TV. This is not a
malfunction.
• Discs respond differently to particular player functions. This may result in the
screen becoming black for a brief instant or shaking slightly when the function is
executed. These problems are largely due to differences between discs and disc
content and are not malfunctions of this player.
Noticeable difference in
DVD and CD volume.
• DVDs and CDs use different recording methods. This is not a malfunction.
CD-ROM disc is not
recognized.
• Make sure that the CD-ROM was recorded using the ISO 9660 disc format. See
Disc compatibility table on page 31 for more on disc compatibility.
DVD-ROM disc is not
recognized.
• Make sure that the DVD-ROM was recorded using the UDF bridge format. See
Disc compatibility table on page 31 for more on disc compatibility.
Additional information
38
En
Tuner
USB connection
Files don’t show up in
the Disc Navigator/
Photo Browser.
• The files on the disc must be named with the correct file extension: .mp3 for MP3
files; .wma for WMA files; .m4a for MPEG-4 AAC files; .jpg for JPEG files (upper or
lower-case is OK). See Disc compatibility table on page 31.
Can’t play WMA or
MPEG-4 AAC files.
• The files were recorded using DRM (digital rights management). This is not a
malfunction.
Problem Remedy
Problem Remedy
Considerable noise in
radio broadcasts.
• Connect the AM antenna (refer to the Setup Guide) and adjust the direction and
position for best reception. You may also connect an additional internal or external
AM antenna (refer to Connecting auxiliary audio components on page 29).
• Fully extend the FM wire antenna, position for best reception, and secure to a
wall. You may also connect an outdoor FM antenna (see Connecting external
antennas on page 29).
• Turn off other equipment that may be causing the noise or move it further away.
• The tuning interval is incorrect for your country or region. See Frequency
step setting on page 35 to switch the tuning interval.
Auto tuning does not
pick up some stations.
• The radio signal is weak. Auto tuning will only detect radio stations with a good
signal. For more sensitive tuning, connect an outdoor antenna.
Problem Remedy
USB mass storage
device is not recognized
by the system.
• Make sure you have completely inserted the USB connector to this unit.
• Check that the memory format is FAT16 or FAT32.
• USB devices with an internal USB hub are not supported.
Files don’t show up in
the Navigator/Photo
Browser.
• The files must have the correct file extension: .mp3 for MP3 files; .wma for WMA
files; .m4a for MPEG-4 AAC files; .jpg for JPEG files (upper or lower-case is OK).
• Make sure the file permission hasn’t been restricted (through a password, etc.).
Can’t play WMA or
MPEG-4 AAC files.
• The files were recorded using DRM (digital rights management). This is not a
malfunction.
Additional information 09
39
En
English FrançaisDeutsch
Nederlands
Italiano Español
Error Messages
Resetting the system
Use the front panel controls to reset all system
settings to the factory default.
• With the system on, press
STANDBY/
ON
while holding down USB.
The next time you switch on, all the system
settings should be reset.
Setting the Key Lock
You can disable the front panel buttons by
switching the Key Lock feature on.
1
With the system in standby, p
ress
SETUP
and use
/
to choose KEYLOCK then press
ENTER
.
This is shown in the front panel display.
2 Use
/
to select LOCK ON or LOCK OFF
then press
ENTER
.
Switching off the demo
Follow the steps below to switch the automatic
demo feature off (this starts when you plug in
for the first time):
1 With the unit in standby, press
SETUP
.
2 Use
/
to choose DEMO then press
ENTER
.
3 Use
/
to
select DEMO OFF
and press
ENTER
.
Using the language code list
Some of the language options (see Language
settings on page 25) allow you to set your
preferred language from any of the 136
languages in the Language code list below.
1 Select ‘Other Language’.
2 Use
/
to select either a code letter or
a code number.
3 Use
/
to select a code letter or a code
number.
See the Language code list (next page) for a
complete list of languages and codes.
Message Description
SND. DEMO • The sound demo is on. See General in Troubleshooting on page 36.
CANNOT • An operation is prohibited because DVD/CD isn’t selected, headphones are
connected, or TEST TONE
is pressed during disc playback.
MUTING • An operation is prohibited because the sound is muted (press MUTE
).
STEREO • An operation is prohibited because the DVD/CD or USB function isn’t selected.
TRAYLOCK • The tray lock is on. See General in Troubleshooting on page 36.
USB ERR • See in Important Using the USB interface on page 22 for more on this.
EEP ERR • Contact your Pioneer authorized service center or your dealer for servicing.
EXIT • Appears when a menu is automatically exited after a set period of inactivity.
Additional information09
40
En
Language code list
Language (Language code letter), Language code
Country/Area code list
Country/Area, Country/Area code,
Country/Area code letter
Japanese (ja), 1001
English (en), 0514
French (fr), 0618
German (de), 0405
Italian (it), 0920
Spanish (es), 0519
Dutch (nl), 1412
Russian (ru),
1821
Chinese (zh), 2608
Korean (ko), 1115
Greek (el), 0512
Afar (aa), 0101
Abkhazian (ab), 0102
Afrikaans (af), 0106
Amharic (am), 0113
Arabic (ar),
0118
Assamese (as), 0119
Aymara (ay), 0125
Azerbaijani (az), 0126
Bashkir (ba), 0201
Byelorussian (be), 0205
Bulgarian (bg), 0207
Bihari (bh),
0208
Bislama (bi), 0209
Bengali (bn),
0214
Tibetan (bo), 0215
Breton (br), 0218
Catalan (ca), 0301
Corsican (co), 0315
Czech (cs), 0319
Welsh (cy), 0325
Danish (da), 0401
Bhutani (dz),
0426
Esperanto (eo),
0515
Estonian (et), 0520
Basque (eu), 0521
Persian (fa), 0601
Finnish (fi), 0609
Fiji (fj), 0610
Faroese (fo), 0615
Frisian (fy), 0625
Irish (ga), 0701
Scots-Gaelic (gd), 0704
Galician (gl), 0712
Guarani (gn), 0714
Gujarati (gu), 0721
Hausa (ha), 0801
Hindi (hi), 0809
Croatian (hr), 0818
Hungarian (hu), 0821
Armenian (hy), 0825
Interlingua (ia), 0901
Interlingue (ie), 0905
Inupiak (ik), 0911
Indonesian (in), 0914
Icelandic (is), 0919
Hebrew (iw), 0923
Yiddish (ji), 1009
Javanese (jw), 1023
Georgian (ka), 1101
Kazakh (kk), 1111
Greenlandic (kl), 1112
Cambodian (km), 1113
Kannada (kn), 1114
Kashmiri (ks), 1119
Kurdish (ku), 1121
Kirghiz (ky), 1125
Latin (la), 1201
Lingala (ln), 1214
Laothian (lo), 1215
Lithuanian (lt), 1220
Latvian (lv), 1222
Malagasy (mg), 1307
Maori (mi), 1309
Macedonian (mk), 1311
Malayalam (ml), 1312
Mongolian (mn), 1314
Moldavian (mo), 1315
Marathi (mr), 1318
Malay (ms), 1319
Maltese (mt), 1320
Burmese (my), 1325
Nauru (na), 1401
Nepali (ne), 1405
Norwegian (no), 1415
Occitan (oc), 1503
Oromo (om), 1513
Oriya (or), 1518
Panjabi (pa), 1601
Polish (pl), 1612
Pashto, Pushto (ps), 1619
Portuguese (pt), 1620
Quechua (qu), 1721
Rhaeto-Romance (rm), 1813
Kirundi (rn), 1814
Romanian (ro), 1815
Kinyarwanda (rw), 1823
Sanskrit (sa), 1901
Sindhi (sd), 1904
Sangho (sg), 1907
Serbo-Croatian (sh), 1908
Sinhalese (si), 1909
Slovak (sk), 1911
Slovenian (sl), 1912
Samoan (sm), 1913
Shona (sn), 1914
Somali (so), 1915
Albanian (sq), 1917
Serbian (sr), 1918
Siswati (ss), 1919
Sesotho (st), 1920
Sundanese (su), 1921
Swedish (sv), 1922
Swahili (sw), 1923
Tamil (ta), 2001
Telugu (te), 2005
Tajik (tg), 2007
Thai (th), 2008
Tigrinya (ti), 2009
Turkmen (tk), 2011
Tagalog (tl), 2012
Setswana (tn), 2014
Tonga (to), 2015
Turkish (tr), 2018
Tsonga (ts), 2019
Tatar (tt), 2020
Twi (tw), 2023
Ukrainian (uk), 2111
Urdu (ur), 2118
Uzbek (uz), 2126
Vietnamese (vi), 2209
Volapük (vo), 2215
Wolof (wo), 2315
Xhosa (xh), 2408
Yoruba (yo), 2515
Zulu (zu), 2621
Argentina, 0118, ar
Australia, 0121, au
Austria, 0120, at
Belgium, 0205, be
Brazil, 0218, br
Canada, 0301, ca
Chile, 0312, cl
China, 0314, cn
Denmark, 0411, dk
Finland, 0609, fi
France, 0618, fr
Germany, 0405, de
Hong Kong, 0811, hk
India, 0914, in
Indonesia, 0904, id
Italy, 0920, it
Japan, 1016, jp
Korea, Republic of, 1118, kr
Malaysia, 1325, my
Mexico, 1324, mx
Netherlands, 1412, nl
New Zealand, 1426, nz
Norway, 1415, no
Pakistan, 1611, pk
Philippines, 1608, ph
Portugal, 1620, pt
Russian Federation, 1821, ru
Singapore, 1907, sg
Spain, 0519, es
Switzerland, 0308, ch
Sweden, 1905, se
Taiwan, 2023, tw
Thailand, 2008, th
United Kingdom, 0702, gb
United States of America, 2119, us
Additional information 09
41
En
English FrançaisDeutsch
Nederlands
Italiano Español
Specifications
• Amplifier section
RMS Power Output:
Front, Center, Surround . . . 60 W per channel
(1 kHz, 10 % T.H.D., 4 Ω)
50 W per channel
(1 kHz, 10 % T.H.D., 6 Ω)
Subwoofer . . 60 W (100 Hz, 10 % T.H.D., 4
Ω)
50 W (100 Hz, 10 % T.H.D., 6 Ω)
• Disc section
Digital audio
characteristics . . . . . . . . . DVD fs: 96 kHz, 24-bit
Type. . . . . . . .DVD system, Video CD/Super VCD
system and Compact Disc digital audio system
Frequency
response. . . . 4 Hz to 44 kHz (96 kHz sampling) /
4 Hz to 22 kHz (48 kHz sampling)
Wow and Flutter. . . . . . . . Limit of measurement
(±0.001 % W.PEAK) or less (JEITA)
• FM tuner section
Frequency range . . . . . . . . 87.5 MHz to 108 MHz
Antenna . . . . . . . . . . . . . . . . . . 75
Ω, unbalanced
• AM tuner section
Frequency range:
With 9 kHz step . . . . . . . . 531 kHz to 1602 kHz
With 10 kHz step . . . . . . . 530 kHz to 1700 kHz
Antenna . . . . . . . . . . . . . . . . . . . . . Loop antenna
• Miscellaneous
Power requirements:
Singapore, Indonesia, Hong Kong, Malaysia,
Philipines models
. . . . . . . . . . . AC 220 V to 240 V, 50 Hz / 60 Hz
Taiwanese model. . . . AC 110 V, 50 Hz / 60 Hz
Power consumption . . . . . . . . . . . . . . . . . . . 44 W
Power consumption in standby . . . . . . . . 0.38 W
Dimensions
. . 420 mm (W) x 60 mm (H) x 330 mm (D)
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.1 kg
• Accessories (DVD/CD receiver)
Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . 1
AA/R6 dry cell batteries
(to confirm system operation) . . . . . . . . . . . . . . 2
Video cable (yellow plugs) . . . . . . . . . . . . . . . . . 1
AM loop antenna . . . . . . . . . . . . . . . . . . . . . . . . . 1
FM antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Power cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Setup Guide
These operating instructions
S-DV151 Speaker system
• Front speakers
Enclosure . . . . . . . . . Closed-box bookshelf type
(magnetically shielded)
System. . . . . . . . . . . . . . . . . 7.7 cm 1-way system
Speakers . . . . . . . . . . . . . . . . . . 7.7 cm cone type
Nominal impedance. . . . . . . . . . . . . . . . . . . . 6
Ω
Frequency range . . . . . . . . . . . . 90 Hz to 20 kHz
Maximum input power. . . . . . . . . . . . . . . . . 60 W
Dimensions
. 105 mm (W) x 115 mm (H) x 114 mm (D)
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.6 kg
• Center speaker
Enclosure . . . . . . . . . Closed-box bookshelf type
(magnetically shielded)
System. . . . . . . . . . . . . . . . . 7.7 cm 1-way system
Speakers . . . . . . . . . . . . . . . . . . 7.7 cm cone type
Nominal impedance. . . . . . . . . . . . . . . . . . . . 6
Ω
Frequency range . . . . . . . . . . . . 90 Hz to 20 kHz
Maximum input power. . . . . . . . . . . . . . . . . 60 W
Dimensions
. 115 mm (W) x 105 mm (H) x 114 mm (D)
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.6 kg
• Surround speakers
Enclosure . . . . . . . . . Closed-box bookshelf type
(magnetically shielded)
System. . . . . . . . . . . . . . . . . 7.7 cm 1-way system
Speakers . . . . . . . . . . . . . . . . . . 7.7 cm cone type
Nominal impedance. . . . . . . . . . . . . . . . . . . . 6
Ω
Frequency range . . . . . . . . . . . 100 Hz to 20 kHz
Maximum input power. . . . . . . . . . . . . . . . . 60 W
Dimensions
. 105 mm (W) x 118 mm (H) x 114 mm (D)
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.63 kg
• Subwoofer
Enclosure . . . . . . Bass-reflex floorstanding type
System. . . . . . . . . . . . . . . . . 16 cm 1-way system
Speaker . . . . . . . . . . . . . . . . . . . .16 cm cone type
Nominal impedance. . . . . . . . . . . . . . . . . . . . 6
Ω
Frequency range . . . . . . . . . . . . 30 Hz to 2.0 kHz
Maximum Input Power. . . . . . . . . . . . . . . . . 60 W
Dimensions
. 190 mm (W) x 360 mm (H) x 317 mm (D)
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.2 kg
Additional information09
42
En
• Accessories
Non-skid pads (small). . . . . . . . . . . . . . . . . . . . 12
Non-skid pads (large) . . . . . . . . . . . . . . . . . . . . . 4
Mounting brackets . . . . . . . . . . . . . . . . . . . . . . . 4
Screws (for mounting brackets) . . . . . . . . . . . . 4
S-DV1T, S-DV252SW Speaker system
• Front/surround speakers (S-DV1T)
Enclosure. . . . . . . Closed-box floorstanding type
(magnetically shielded)
System . . . . . . . . . . . . . . . . . . . . . . . 2-way system
Speakers:
Woofer . . . . . . . . . . . . . . . 7.7 cm cone typex2
Tweeter . . . . . . . . . . . .2.6 cm semi-dome type
Nominal impedance. . . . . . . . . . . . . . . . . . . . 4
Ω
Frequency range . . . . . . . . . . . . 70 Hz to 20 kHz
Maximum input power . . . . . . . . . . . . . . . . 100 W
Dimensions
260
mm
(W) x 1096.5
mm
(H) x 260
mm
(D)
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.2 kg
• Center speaker (S-DV1T)
Enclosure. . . . . . . . . . Closed-box bookshelf type
(magnetically shielded)
System . . . . . . . . . . . . . . . . . 7.7 cm 1-way system
Speakers . . . . . . . . . . . . . . . . . . 7.7 cm cone type
Nominal impedance. . . . . . . . . . . . . . . . . . . . 4
Ω
Frequency range . . . . . . . . . . . . 75 Hz to 20 kHz
Maximum input power . . . . . . . . . . . . . . . . 100 W
Dimensions
. . . .270 mm (W) x 96 mm (H) x 90 mm (D)
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.78 kg
• Subwoofer (S-DV252SW)
Enclosure. . . . . . . Bass-reflex floorstanding type
System . . . . . . . . . . . . . . . . . 16 cm 1-way system
Speaker . . . . . . . . . . . . . . . . . . . 16 cm cone type
Nominal impedance. . . . . . . . . . . . . . . . . . . . 4
Ω
Frequency range . . . . . . . . . . . . 30 Hz to 2.5 kHz
Maximum Input Power. . . . . . . . . . . . . . . . . 60 W
Dimensions
. . 190
mm
(W) x 360
mm
(H) x 320
mm
(D)
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.0 kg
• Accessories
Speaker cables . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Speaker cables (for S-DV252SW) . . . . . . . . . . . 1
Small non-skid pads (for center speaker). . . . . 4
Large non-skid pads
(for front and surround speakers) . . . . . . . . . . 16
Large non-skid pads (for subwoofer) . . . . . . . . 4
Speaker stand bases . . . . . . . . . . . . . . . . . . . . . . 4
Screws (for bases) . . . . . . . . . . . . . . . . . . . . . . . 12
Note
• Specifications and design subject to
possible modification without notice, due
to improvements.
This product includes FontAvenue®
fonts licenced by NEC corporation.
FontAvenue is a registered trademark
of NEC Corporation.
This product incorporates copyright
protection technology that is protected
by method claims of certain U.S. patents
and other intellectual property rights
owned by Macrovision Corporation and
other rights owners. Use of this copyright
protection technology must be authorized
by Macrovision Corporation, and is
intended for home and other limited uses
only unless otherwise authorized by
Macrovision Corporation. Reverse
engineering or disassembly is prohibited.
DRM (digital rights management)
copy protection is a technology
designed to prevent unauthorized
copying by restricting playback, etc. of
compressed audio files on devices
other than the PC (or other recording
equipment) used to record it. For
detailed information, please see the
instruction manuals or help files that
came with your PC and/or software.
Produkt Specifikationer
| Mærke: | Pioneer |
| Kategori: | Hjemmesystem |
| Model: | HTZ151DVD |
Har du brug for hjælp?
Hvis du har brug for hjælp til Pioneer HTZ151DVD stil et spørgsmål nedenfor, og andre brugere vil svare dig
Hjemmesystem Pioneer Manualer
5 Juli 2024
5 Juli 2024
4 Juli 2024
4 Juli 2024
4 Juli 2024
28 Juni 2024
Hjemmesystem Manualer
Nyeste Hjemmesystem Manualer
22 August 2024
15 August 2024
6 Juli 2024
4 Juli 2024
4 Juli 2024
4 Juli 2024
4 Juli 2024
28 Juni 2024