Pioneer SP-C21 Manual

Pioneer Højttaler SP-C21

Læs gratis den danske manual til Pioneer SP-C21 (16 sider) i kategorien Højttaler. Denne vejledning er vurderet som hjælpsom af 26 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 13.5 anmeldelser. Har du et spørgsmål om Pioneer SP-C21, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/16
Speaker System Système d’enceintes Sistema de Bocinas
Operating Guide Guide d’utilisation Guía de Operaciones
SP-FS51-LR, SP-BS21-LR & SP-C21
IMPORTANT NOTICE: The serial number for the equipment is located on the rear of the product.
Please write this serial number on the warranty sheet and keep it in a secure area for future reference.
BEFORE USE
• Thank you for buying this Pioneer product.
• Please read through this operating guide before using your
speaker system to optimize performance. After you have
finished reading this operating guide, store it in a safe place
for future reference.
• The nominal impedance of this speaker system is 8 ohms.
Connect the speaker system to a stereo amplifier with a load
impedance rating ranging from 4 to 16 ohms (a model with
“4-16 ” displayed on the speaker output terminals).Ω
• In order to prevent damage to the speaker system resulting
from input overload, please observe the following precautions:
• Do not supply power to the speaker system in excess of
the maximum permissible input.
• When connecting or disconnecting cables, be sure
amplifier power is OFF.
• Do not use excessive amplifier volume if using a graphic
equalizer to emphasize high or low frequencies.
REMARQUE IMPORTANTE: Le numéro de série pour l’équipement se trouve sur l’arrière du produit. Veuillez écrire le numéro
de série sur la carte de garantie et le conserver dans un lieu sûr pour éventuellement le consulter plus tard.
AVANT TOUTE UTILISATION
• Merci d’avoir acheté ce produit Pioneer.
• Veuillez lire le présent guide d’utilisation dans son intégralité
avant d’utiliser le système d’enceintes pour en optimiser
sa performance. Après avoir fini la lecture de ce guide
d’utilisation, conservez-le dans un lieu sûr pour éventuelle-
ment le consulter plus tard.
• L’impédance nominale de ce système d’enceintes est de 8
ohms. Raccordez les enceintes acoustiques à un amplifica-
teur stéréophonique dont la valeur nominale d’impédance de
charge va de 4 à 16 ohms (un modèle pour lequel « 4-16 » Ω
est indiqué sur les bornes de sortie aux haut-parleurs).
• Pour éviter d’endommager les enceintes acoustiques par une
surcharge à l’entrée, observez les précautions suivantes :
• Ne fournissez pas aux enceintes acoustiques une puis-
sance électrique dépassant l’entrée maximale autorisée.
• Lors de la connexion ou de la déconnexion des câbles,
veillez à mettre l’amplificateur hors tension.
• N’utilisez pas de volume d’amplificateur excessif lors de
l’utilisation d’un égaliseur graphique pour accentuer les
hautes ou basses fréquences.
AVISO IMPORTANTE: El número de serie del equipo está ubicado en la parte posterior del producto. Por favor anote el
número de serie en la hoja de garantía y guárdelo en un lugar seguro para usarlo como futura referencia.
ANTES DE USARLO
• Gracias por comprar este producto Pioneer.
• Por favor lea esta guía de operaciones antes de usar su
sistema de bocinas, a fin de optimizar el funcionamiento.
Una vez que haya terminado de leer esta guía de opera-
ciones, guárdela en un lugar seguro para usarla como
referencia en el futuro.
• La impedancia nominal de este sistema de bocinas es 8 ohmios.
Conecte el sistema de bocinas a un amplificador estéreo con
una impedancia de carga de 4 a 16 ohmios (un modelo que
indique “4-16Ω” en los terminales de salida a bocinas).
• Para evitar dañar el sistema de bocinas por una sobrecarga
a la entrada, tome las siguientes precauciones:
• No suministre más potencia de entrada al sistema de
bocinas que la máxima permitida.
• Cuando conecte o desconecte cables, verifique que la
corriente al amplificador esté APAGADA.
• No use un volumen excesivo del amplificador si usa
un ecualizador gráfico para enfatizar las altas o bajas
frecuencias.
SP-C21
SP-BS21
(180.68 mm x 320 mm ) SP-FS51-LRSP-BS21-LR
2
www.pioneerelectronics.com
CONNECTING YOUR SYSTEM
IMPORTANT: Make sure all equipment is turned off before making any connections.
Correct wiring of your loudspeakers is essential for achieving the best sound quality. Be careful to ensure
proper polarity of connection. We recommend a minimum of 18 gauge for runs up to 25 feet, and thicker for
longer runs.
Most loudspeaker cable is coded to ease this task. Typically the ribbed or striped side is connected to the
positive (red) terminal. Make sure that the amplifier positive (red) terminal is connected to the loudspeaker
positive (red) terminal. Strip off ½” of insulation from the ends of the cable, twist the bare strands and insert
into the binding posts. Take care that no stray strands of wire short across between the terminals.
1: Strip the cover and twist the strands 2: Connect each speaker cable (not supplied) to one set of
the receiver’s speaker output terminals and the speaker input
terminals. The red terminal is the positive (+), and the black
terminal is the negative (–). Make sure that the receiver positive
(red) terminal is connected to the speaker positive (red) terminal.
ENGLISH
Wire going to positive
terminal of receiver
Wire going to negative
terminal of receiver
Negative Positive
PLACEMENT AND FINE TUNING
Correct placement is important for maximizing the sound
quality of your loudspeaker system. Take time to experiment
with positioning according to the guidelines below.
Using the SP-FS51-LR or SP-BS21-LR as Front and
Surround Speakers
For best results the tweeter should be positioned near
ear level and the loudspeakers separated a distance
approximately equal to the listening distance. Angling the
loudspeakers inward towards the listener will improve the
image stability for non-central listeners. Close proximity
to a side or rear wall will enhance the bass performance,
although too close (particularly a corner location) and the
bass may be unnaturally high and image performance
may be degraded. Best results will be obtained when
the loudspeaker is placed approximately 2 feet from the
wall. If a corner location is unavoidable, try to position the
loudspeaker so that the distance to the rear wall is not
equal to the distance to the side wall.
INSTALLING THE BASE TO THE SP-FS51-LR
FLOORSTANDING SPEAKERS
Included in the SP-FS51-LR carton are (2) bases and (8)
screws. Attach the base to the bottom of each speaker
using (4) screws, as illustrated. (Screwdriver is not included.)
USING FEET WITH THE SP-C21 CENTER-
CHANNEL SPEAKER
Included in the SP-C21 carton are (2) feet for the SP-C21
to rest on. Place the feet at the desired location of the
speaker. They can be spaced a variety of widths apart
for installation flexibility. Once the SP-C21 is placed on
the feet, tilt the speaker to the desired angle, depending
on the location of the speaker in relation to the desired
listening position.
NOTE: Do not use adhesive or screws to attach the feet
to the speaker. Doing this will damage the cabinet and
void the warranty.

Produkt Specifikationer

Mærke: Pioneer
Kategori: Højttaler
Model: SP-C21

Har du brug for hjælp?

Hvis du har brug for hjælp til Pioneer SP-C21 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Højttaler Pioneer Manualer

Pioneer

Pioneer RM-07 Manual

30 December 2025
Pioneer

Pioneer TS-A4671F Manual

14 December 2024
Pioneer

Pioneer TS-A6881F Manual

14 December 2024
Pioneer

Pioneer TS-A6961F Manual

14 December 2024
Pioneer

Pioneer TS-A1371F Manual

14 December 2024
Pioneer

Pioneer TS-A1671F Manual

14 December 2024
Pioneer

Pioneer TS-M801PRO Manual

14 December 2024
Pioneer

Pioneer TS-M651PRO Manual

14 December 2024
Pioneer

Pioneer TS-W3020PRO Manual

14 December 2024
Pioneer

Pioneer TS-6900PRO Manual

14 December 2024

Højttaler Manualer

Nyeste Højttaler Manualer

DS18

DS18 PRO-FR6NEO Manual

16 Juni 2025
DS18

DS18 SLG-AR6V2 Manual

16 Juni 2025
DS18

DS18 Hydro NXL-6 Manual

16 Juni 2025
DS18

DS18 PRO-HY6.4B Manual

16 Juni 2025
DS18

DS18 PRO-HY6MSL Manual

16 Juni 2025
DS18

DS18 HYDRO JK-BD-LR Manual

16 Juni 2025
Induction Dynamics

Induction Dynamics S1.8SW Manual

16 Juni 2025
DS18

DS18 PRO-NS 6.4 Manual

16 Juni 2025
DS18

DS18 Hydro NXL-PS6 Manual

16 Juni 2025
Energizer

Energizer BTS081 Manual

16 Juni 2025