Popp Z-Weather Manual

Popp Smart hjem Z-Weather

Læs gratis den danske manual til Popp Z-Weather (8 sider) i kategorien Smart hjem. Denne vejledning er vurderet som hjælpsom af 3 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 2 anmeldelser. Har du et spørgsmål om Popp Z-Weather, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/8

Quick Start

Z-Weather is a cup anemometer for Z-Wave installations. It continually measures the wind

speed and can, for example, trigger closing of the awnings and blinds if it is too windy. In

order to charge Z-Weather place it in a location with direct sunlight exposure for 3-4 hours.

Without direct sun light, charging may take 12 hours. Inclusion and exclusion are performed

by clicking the button on the back of the device three times.

Please refer to the chapters below for detailed information about all aspects of the products

usage.

Z-Weather

Wind and Weather Sensor

Manual

005206

Product Description

Z-Weather is a cup anemometer for Z-Wave installations. It continually measures the wind

speed and can, for example, trigger closing of the awnings and blinds if it is too windy. It

also measures the amount of rotation, enabling calculation of the wind yield per day or per

year. In addition, Z-Weather includes sensors for humidity, temperature, air pressure and

dew point, essentially providing the core sensors of a weather station.

Z-Weather is powered by a solar cell and stores energy on an internal capacitor, enabling

continuous operation, even with few sun for a couple of days. It does not use any batteries

and is completely maintenance free. Using the built-in solar cell it also measures the

ambient light and the solar yield. This information can be used to turn on the outdoor light at

dusk time and turn the light off in the morning.

Z-Weather‘s wind yield and solar yield metering can be used as a calculation base for

planning a wind generator or a solar panel on the roof of a house. Z-Weather can be

included and operated in any Z-Wave network with Z-Wave certified devices from other

manufacturers and/or other applications.

All non-battery operated nodes within the Z-Wave network will act as repeaters regardless of

vendor to increase reliability of the network and will enable Z-Weather to be contacted

reliably even in larger installations.

During normal operation, Z-Weather is limiting continuous measurement to wind speed and

solar radiation, other sensors are operating only on demand. This conservative energy

management ensures continuous operation with the limited energy harvested from the solar

cell powering Z-Weather. The Z-Wave radio frequency transmitter is turned off most of the

time and is turned on if there is too much wind, at twilight time and on a continuous base,

depending on the energy budget. The wake up interval is between five minutes at noon in

summer and five hours in the second half of the night in winter. Z-Weather also wakes up on

pushing the button.

Installation Guidelines

Before you can configure and use Z-Weather, the unit needs to be fully charged. In order to

charge Z-Weather place it in a location with direct sunlight exposure for 4-6 hours. Without

Z-Weather: Operating elements

Function Button

and Status LED

Solar Cell

Produkt Specifikationer

Mærke:	Popp
Kategori:	Smart hjem
Model:	Z-Weather
Kode for international beskyttelse (IP):	IP34
Bredde:	330 mm
Dybde:	300 mm
Højde:	110 mm
Vægt:	300 g
Produktfarve:	Sort
Forbindelsesteknologi:	Trådløs
LED-indikatorer:	Ja
Strømkilde type:	Solar
Maksimal indendørs rækkevidde:	20 m
Maksimal udendørsinterval:	100 m
Trådløs teknologi:	Z-Wave
Grænseflade:	RF trådløst
Frekvens:	868.42 MHz
Vindhastighed, måleinterval:	0 - 44.4 m/s
Måle miljøforhold:	Humidity, Sunlight intensity, Temperature, Wind speed