PowerWalker VI 750 R1U Manual

PowerWalker Uafbrydelig strømforsyning (UPS) VI 750 R1U

Læs gratis den danske manual til PowerWalker VI 750 R1U (2 sider) i kategorien Uafbrydelig strømforsyning (UPS). Denne vejledning er vurderet som hjælpsom af 14 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 7.5 anmeldelser. Har du et spørgsmål om PowerWalker VI 750 R1U, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

L -ine interactive UPS

PowerWalker /750/1000/1500VI 500 R1U

User Manual K01 C000402- -01

IMPORTANT SAFETY INSTRUCTIONS

(SAVE THESE INSTRUCTIONS)

This manual contains important safety instructions. Please read and follow all instructions carefully during installation and operation of the unit. Read this

manual thoroughly before attempting to unpack, install, or operate your UPS.

CAUTION! To prevent the risk of fire or electric shock, install in a temperature and humidity controlled indoor area free of conductive contaminants. (See the

specifications for the acceptable temperature and humidity range.)

CAUTION! To reduce the risk of overheating the UPS, do not cover the UPS' cooling vents and avoid exposing the unit to direct sunlight or installing the unit

near heat emitting appliances such as space heaters or furnaces.

CAUTION! -Do not attach non computer- - related items, such as medical equipment life, support equipment, microwave ovens, or vacuum cleaners to UPS.

CAUTION! Do not plug the UPS input into its own output.

CAUTION! Do not allow liquids or any foreign object to enter the UPS. Do not place beverages or any other liquid containing vess- els on or near the unit.

CAUTION! In the event of an emergency, press the OFF button and disconnect the power cord from the AC power supply to properly disable the UPS.

CAUTION! Do not attach a power strip or surge suppressor to the UPS.

CAUTION! Unplug the UPS prior to cleaning and do not use liquid or spray detergent.

INSTALLING YOUR UPS SYSTEM

UNPACKING

The box should contain the following:

(1)UPS Unit1 (2); User Manual1;

HOW TO DETERMINE THE POWER REQUIREMENTS OF YOUR EQUIPMENT

1. Ensure that the equipment plugged into the battery power supplied outlets does not exceed the UPS unit’s rated capacity. If rated unit capacities are -

exceeded, an overload condition may occur and cause the UPS unit to shut down or the fuse blow.

2. There are many factors that can affect the amount of power that your computer system will require. For optimal system performance keep the load

below 80% of the unit’s rated capacity.

HARDWARE INSTALLATION GUIDE

1. Your new UPS may be used immediately upon receipt. However, recharging the battery for 8 at least hours is recommended to ensure that the battery's

maximum charge capacity is achieved. Charge loss may occur during shipping and storage. To recharge the battery, simply leave the unit plugged into

an AC outlet. The unit will charge in both the on and off position.

2. With the UPS unit off and unplugged, connect the computer, monitor, and any externally powered data storage device.

3. Plug the UPS into a 2 pole, 3 wire grounded receptacle (wall outlet). Make sure the wall branch outlet is protected by a fuse or circuit breaker and does

not service equipment with large electrical demands.

4. Depress the power switch to turn the unit on. The LCD indicator light will illuminate and the unit will "beep".

5. To maintain optimal battery charge, leave the UPS plugged into an AC outlet at all times.

6. To store your UPS for an extended period, cover it and store with the battery fully charged. Recharge the battery every three months to ensure battery

life.

ROUTINE MAINTENANCE AND STORAGE

ROUTINE MAINTENANCE

1. Use dry soft clothes to clean the front panel and plastic parts. Do not use any detergent that contains alcoholic ingredient.

2. The expected lifetime of the battery is around 3 years. Improper operation and harsh environment will reduce the actual lifetime.

3. Unplug the UPS from power inlet if the UPS will not operate for long period of time.

STORAGE

1. First turn off your UPS and disconnect its power cord from the wall outlet. Disconnect all cables connected the UPS to avoid battery drain.

2. The UPS should be stored in a cool dry location.

3. Make sure the battery is fully charged before the UPS is stored.

4. For extended storage in moderate climates, the battery should be charged for 12 hours every 3 months by plugging the power cord into the wall

receptacle and turning on the main switch. Repeat it every 2 months in high temperature locations.

BASIC OPERATION

FRONT AND TOP PANEL DESCRIPTION

PowerWalker VI 500/750/1000/1500 1U R

1. AC Inlet

Connect to utility power through power cordthe input .

2. Input Circuit Fuse

The fuse provides optimal overload protection.

3. AC outlet

The UPS provides outlets for connected equipment to insure temporary uninterrupted operation during a power failure and against surges and spi kes.

4. SNMP/HTTP Network Port

The SNMP/HTTP port provides remote monitoring and management of your UPS over a network.

5. Serial Port

This port allows connection and communication from the DB9 serial on the computer to the UPS unit. The UPS communicates its status to the

software.

6. USB Port

This port allows connection and communication form the USB port on the computer to the UPS unit.

7. EPO Port

Enables an emergency UPS Power- Off from a remote location. EPO terminal open, the UPS will turn off and the output shutdown immediately.

8. L CD Display

The LCD will display the UPS status including input voltage, output voltage, runtime, percentage of load and battery, etc.

9. Power On/O Switch

Press the power switch to turn the UPS ON or OFF.

10. Mute Button

The audible alarm can be turned off/on by pressing this button .

SOFTWARE DOWNLOAD

Power Master management software provides a user friendly interface for your power systems. The graphic user- -interface is intuitive and displays essential

power information at a glance. Please follow procedure below to install the software.

Installation procedure:

1.Download Power Master from the website:

http://www.powermaster. powerwalker.com

2.Double-click the file and follow the installation steps.

3.When your computer restarts, the Power Master

software will appear as a blue icon located in the

system tray.

TECHNICAL SPECIFICATIONS

LCD Indication

Line mode

Bat- mode

Alarm/F ault

Sound disable

(Press the mute key 3s to disable

and enable the buzzer sound)

Bat mode: battery capacity

Line mode:

1. Battery charging: cycle lighting

2. Battery full charged: lighting

3. Line mode without charger:

battery capacity

Load capacity

Initial

AC INPUT(Voltage)

OUTPUT

(Voltage)

Alarm DEFINITIONS

Alarm Condition

Off Normal

Beep 1 time In Every 30 Seconds Utility Failure - The UPS is providing battery power to outlets.

Beep 1 time In Every 2 Seconds

Utility Failure - The UPS is providing battery power.

The rapid beeps indicate the battery will run out of power shortly.

Beep 1 time In Every 0.5 Second

Overload - Occurs when connected equipment exceeds the rating of the unit.

Turn the UPS off and unplug at least one piece of equipment from the UPS.

TROUBLE SHOOTING

Problem

Possible Cause

Solution

The UPS does not perform

expected runtime.

Batteries are not fully charged.

Recharge the battery by leaving the UPS plugged in.

Battery is slightly worn out. Contact Technical Support.

The UPS will not turn on.

The on/off switch is designed to prevent

damage by rapidly turning it off and on.

Turn the UPS off. Wait 10 seconds and then turn the UPS on.

The unit is not connected to an AC outlet. The unit must be connected to a 220 240V 50Hz outlet. -

The battery is worn out. Contact Technical Support.

Mechanical problem.

Contact Technical Support.

Outlets do not provide power to

equipment

Fuse is blown due to overload

Turn the UPS off and unplug at least one piece connected

equipment. Unplug the power cord of the UPS then remove the fuse

compartment beneath the power inlet of the UPS and replace the

blown fuse with a spare one. Lock the compartment back to the UPS.

Connect power cord then turn the UPS on. Make sure that your spare

fuse meets the specification.

Batteries are discharged

Allow the unit to recharge for at least 4 hours.

Unit has been damaged by a surge or spike.

Contact Technical Support.

Software is inactive

The network cable is not connected.

Connect the network cable to the UPS unit and a network port on the

hub.

Software setting problem.

Please read and follow NetAgent utility instruction during installation

and operation of the NetAgen software, or contact technical support.

Fault

Fault code F09

Output Short :

Output circuit short.

1. Shut down the UPS

2. Your attached equipment may have problems, please remove

them and check again.

Fault code F12

Battery Low :

Battery voltage is too low.

1. Shut down the UPS

2. Check the counts of Battery

3.Check battery connector when use battery packages.

Fault code F14

Overload in line Mode:

Your equipment requires more

power than the

UPS can provide. It will shutdown.

Shut essential off non- equipment.If this solves the overload

problem,

the UPS will transfer to normal operation.

Alarm

A larm code A06

Battery

low: Battery capacity is low, UPS will

turn off soon

S - hut off non essential equipment.

S ave your data and turn off computer.

A larm code A14

O ver load occurs.

S - hut off non essential equipment.

Model

PowerWalker VI 500

R1U

PowerWalker VI 750

R1U

PowerWalker VI 1000

R1U

PowerWalker VI 1500

R1U

Capacity (VA)

500VA

750VA

1000VA

1500VA

Capacity (Watts)

3 00W

450W

600W

900W

Input

Input Voltage Range

165 9 V~2 0V

Frequency Range

50Hz +/- 5 Hz

Output

On Battery Output Voltage

Sine Wave at 23 -0Vac +/ 10%

On Battery Output Frequency

50Hz - +/ 1%

Overload Protection

On Utility: Fuse, On Battery: Internal Current Limiting

AVR Function

Boost Function

Yes

Buck Function

Yes

Physical

Total # of UPS Receptacles

IEC C13 x 4

Maximum Dimensions W) (H x D x

44mm x 216mm x 433mm

44mm x mm x 4485 33mm

Weight (Kg)

7 .6

8.6

14.2

16.2

Battery

Sealed Maintenance Free Lead Acid Battery

6V / 7AH x2

6V / 9AH x2

6V / 7AH p2-x4

6V / 9AH p2-x4

Typical Recharge Time

8 Hours

Warning Diagnostics

Indicators

Using AC / Using Battery / Fault

Communication

Software

Windows10/ 8/ 7/ Server2012 /2008 R2, Linux&Mac

Environmental

Operating Temperature

C to 40

Operating Relative Humidity

0 to 90 - % NON CONDENSING

Management

Auto Charger-

Yes

Auto- Restart

Yes

DEFINITIONS FOR ILLUMINATED LCD INDICATORS

Produkt Specifikationer

Mærke:	PowerWalker
Kategori:	Uafbrydelig strømforsyning (UPS)
Model:	VI 750 R1U

Har du brug for hjælp?

Hvis du har brug for hjælp til PowerWalker VI 750 R1U stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Uafbrydelig strømforsyning (UPS) PowerWalker Manualer

PowerWalker VI 2000 RLP Manual

6 Juli 2025

PowerWalker VI 1000 RLP Manual

5 Juli 2025

PowerWalker VFI 3000 RMG PF1 Manual

5 Juli 2025

PowerWalker VI 500 R1U Manual

5 Juli 2025

PowerWalker VI 600 SCL Manual

5 Juli 2025

PowerWalker VFI 3000 TGS Manual

5 Juli 2025

PowerWalker VI 3000 CW Manual

5 Juli 2025

PowerWalker VI 3000 RLP Manual

5 Juli 2025

PowerWalker VFI 10000 AT Manual

5 Juli 2025

PowerWalker VI 1500 R1U Manual

5 Juli 2025

Uafbrydelig strømforsyning (UPS) Manualer

Nyeste Uafbrydelig strømforsyning (UPS) Manualer

Panamax MB1000 Manual

4 September 2025

Panamax MB1500 Manual

4 September 2025

Akyga AK-ND-41 Manual

30 August 2025

CyberPower HSTP3T30KEBCWOB Manual

20 August 2025

Vorago UPS-400 Manual

20 August 2025

CyberPower RT33020KE Manual

20 August 2025

CyberPower Value2200EILCD Manual

20 August 2025

CyberPower OR1000ELCDRM1U Manual

20 August 2025

Vorago UPS-500 Manual

20 August 2025

CyberPower UT1500EI Manual

20 August 2025