Proel Direct100P Manual

Proel Ikke kategoriseret Direct100P

Læs gratis den danske manual til Proel Direct100P (10 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 40 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 20.5 anmeldelser. Har du et spørgsmål om Proel Direct100P, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/10
TECHNICAL SPECIFICATIONS
Model System TypeDIRECT100P 1 channel PASSIVE DI
Input Secon Inseron Loss 26 dB
Input impedance Load impedance> 250 Kohm 600 ohm or greater
Max input level +10 (PAD at 0) dBu XLR maleConnector
+30 (PAD at 20) dBu System performance
+50 (PAD at 40) dBu < 0.007 % (50÷20k Hz 0dBu)Distoron THD
Connectors Frequency response1 x 1/4" jack unbalanced 40 Hz to 20 kHz (-3 dB)
Link 1 x 1/4" jack unbalanced General
Output Secon Controls PAD 0 / -20 / -40, GND LIFT
Output Transformer Balanced Dimensions (W x H x D) 134 x 50 x 105 mm
(isolated with shielding) Weight 0,55 Kg
USER MANUAL
MANUALE D'USO
BENUTZERHANDBUCH
NOTICE D'UTILISATION
MANUAL DE USO

INTRODUCTION
The name DI box comes from direct injecon box, that means exactly: To inject a signal directly or take an
audio signal from the source and send it directly to a mixer console or recorder. Direct boxes perform several
important funcons: they are designed as impedance matching and signal balancing devices. This means that
they take the high impedance of a guitar or keyboard and ‘transform’ it to the low impedance used in balanced
sound systems. Balanced signals inherently cancel noise and, due to their lower impedance, are capable of very
long cable runs. Balanced signals are the norm in professional recording, broadcast and live sound. By properly
matching the impedance you will enjoy beer sound, less noise and an extended frequency response.
DIRECT100P is a passive direct box with transformer and does not require any external power such as phantom
or baeries to work. Just plug-in and play!
The beauty of a transformer is that there is no electrical connecon between the primary and the secondary.
The signal is ‘transformed’ from electrical energy to magnec, then back to electrical; in eect, a ‘magnec
bridge’. This provides two huge benets: with no electrical path, ground loops are eliminated and a tremendous
reducon in common-mode noise is possible. The DIRECT100P features a mic level balanced output XLR
male connector and a high impedance (hi-z) jack input. To obtain both these features the transform rao of
DIRECT100P is 20:1, so DIRECT100P has an inseron loss of 26 dB without any PAD switch depressed.
CONTROLS AND AUDIO CONNECTION
1. INPUT - unbalanced JACK
Connect the source instrument to this 1/4” jack to receive the signal. The input impedance depends on PAD
seng: > 250 Kohm with no pad, 47 Kohm with pad inseron.
2. LINK - unbalanced JACK
Connect this 1/4” jack to the input of the backline instrument or monitor amplier. It is directly connected at
the input. NOTE: If you are using a tube amplier power output (4, 8 or 16 ohm), you must connect always a
speaker of matched impedance in parallel, also using the LINK jack on DIRECT100P; for these connecons you
have to use always jack-jack power cables avoiding jack-jack signal cables.
3. PAD - switch
The pad switch reduces the input signal to the circuit to ensure a clean and distoron-free signal.
Three steps are possible: 0, -20, -40 dB. Always use as lile as aenuaon as possible to get the best possible
signal with reference to the noise oor. The highest aenuaons make possible to connect the DIRECT100P to
any amplier output without saturate the mic input of your mixer desk.
4. GND LIFT - switch
Use the GND LIFT switch to either connect the ground pin of input and output or keep them completely
separated. Depending on the grounding of the connected devices linking or disconnecng will reduce hum
and buzz noises and prevent ground loops. NOTE: Always make sure the GND LIFT is pressed (no ground link)
when connecng to speaker terminals, this prevents accidental short-circuing of the amplier output. Also
make sure the TIP of the input jack is connected to the red wire and that the metal chassis of the DIRECT100P
has no contact with other equipment.
5. BAL OUTPUT - male XLR
This male XLR output connector is the balanced microphone level output of the DI and it is wired with pin-1
ground, pin-2 hot and pin-3 cold.
ENGLISH

Produkt Specifikationer

Mærke: Proel
Kategori: Ikke kategoriseret
Model: Direct100P

Har du brug for hjælp?

Hvis du har brug for hjælp til Proel Direct100P stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Proel Manualer

Proel

Proel Session1 Manual

19 Juni 2025
Proel

Proel Session4 Manual

18 Juni 2025
Proel

Proel Session1 Free Manual

18 Juni 2025
Proel

Proel STRWIFI Manual

22 August 2024
Proel

Proel PB90SSRBK Manual

17 August 2024
Proel

Proel PB90SB Manual

15 August 2024
Proel

Proel Direct100P Manual

14 August 2024
Proel

Proel AMIX54Z Manual

13 August 2024
Proel

Proel Direct100A Manual

12 August 2024
Proel

Proel PB90S Manual

10 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Tripp Lite

Tripp Lite Protect It! TLP606 Manual

30 Juli 2025
AMX

AMX NMX-WP-N2510 Manual

30 Juli 2025
Yealink

Yealink SIP-T23G Manual

30 Juli 2025
Rothenberger

Rothenberger ROBEND 4000 Manual

30 Juli 2025
Tripp Lite

Tripp Lite SUPDMB710 Manual

30 Juli 2025
Tripp Lite

Tripp Lite IBAR6ULTRAUSBB Manual

30 Juli 2025
Advantech

Advantech PCM-34R1TP Manual

30 Juli 2025
Tripp Lite

Tripp Lite SRIN4141410 Manual

30 Juli 2025
Tripp Lite

Tripp Lite TLM609GF Manual

30 Juli 2025
Tripp Lite

Tripp Lite Protect It! TLP368CUBEUAM Manual

30 Juli 2025