Pulsar PSD12020 Manual

Pulsar Batterioplader PSD12020

Læs gratis den danske manual til Pulsar PSD12020 (2 sider) i kategorien Batterioplader. Denne vejledning er vurderet som hjælpsom af 48 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 24.5 anmeldelser. Har du et spørgsmål om Pulsar PSD12020, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

PSD12020

PSD 12V/2A switch mode

power supply desktop for CCTV

Edition: 8 from 01.04.2014

Supersedes edition: 7 from 10.03.2014

Features of the power supply unit:

 power output 2A/12VDC*

 universal AC input voltage range 90÷264V

 high efficiency 83%

 LED optical signalisation

 standby power <0,3W

 efficiency level: V

 protections:

 SCP short-circuit protection

 overvoltage protection (AC input)

 overload (OLP)

 warranty – 2 year from the production date

1. Technical description.

1.1. General description.

Stabilized DC power supply is intended for supply CCTV cameras that require stabilised voltage of The unit has a 12V DC.

cable with a DC5.5/2.1 plug. When connected to fuse blocks of the LB4/xx/xx or LB8/xx/xx family, the power supply unit can feed

more cameras (max. 4 or 8). The unit is protected against short-circuit and overload.

1.2. Technical parameters.

Supply voltage 90 ÷ 264V AC 50÷60Hz

Current consumption 0,23A@230V AC max.

Supply power 24W max.

Efficiency 83%

Output voltage 12V DC

Output current tAMB<30°C 2A - refer to graph 1.

Output current tAMB=40°C 1,4A - refer to graph 1.

Ripple voltage 100mV p-p max.

Short-circuit protection SCP electronic, automatic recovery

Overload protection OLP 105-150% of power supply, automatic recovery

Optical signalisation LED – presence of DC voltage

Operation conditions temperature 0 oC÷40 oC

relative humidity 20%...90%, without condensation

Dimensions (LxWxH) 86 x 72 (50) x32 [mm]

Net/gross weight 0,21kg / 0,24kg

Protection class PN-EN 60950-1:2007 II (second)

Lenght of DC cable 1,45m + plug DC5,5/2,1 female

Lenght of AC cable 1,15m + mains plug

Storage temperature -20ºC...+60ºC

* In order to extend the life of the power supply, the load current of 1,4A is recommended.

Graph 1.

Relation between output current and ambient

temperature (instantaneous load).

Fig.1. Dimension of power supply.

* Refer to graph 1

1.3. Accessories.

For power supplies are available accessories - fuse blocks and cable adapter. For details –visit www.pulsar.pl.

2. Installation.

2.1. Requirements.

The power supply shall be mounted by the qualified installer having appropriate (required and necessary for a given country)

permissions and qualifications for connecting (operating) low-voltage installations. The power supply shall be mounted in closed rooms,

according to the environment class II, of the normal air humidity (RH=90% max. without condensation) and the temperature within the

range from 0°C to +40°C.

The power supply shall be mounted in a close casing (a cubicle, a terminal device) and in order to fulfill LVD and EMC

requirements the rules for power supplies, encasing and shielding shall be observed according to application.

2.2. Installation procedure.

1. Connect the DC output to the load/loads.

2. Connect the power supply unit to the AC line. The power supply has to be installed in such way to keep the air flow

around the supply unit.

3. After tests and operation control are performed, the casing (cubicle) shall be closed etc.

3. Maintenance.

Any and all maintenance operations may be performed following the disconnection of the power supply from the power

network. The power supply does not require any specific maintenance procedures, however, in the case of significant level of dust, it

should be cleaned with the compressed air.

WEEE MARK

According to the EU WEE Directive – It is required not to dispose of electric or electronic waste as

unsorted municipal waste and to collect such WEEE separately.

THE GENERAL WARRANTY CONDITIONS

1. Pulsar K. Bogusz Sp.j. (the manufacturer) grants a two-years warranty for the equipment, counted from the device’s production date.

2. The warranty includes free-of-charge repair or replacement with an appropriate equivalent (the selection is at the manufacturer’s

discretion) if the malfunction is due to the manufacturer, includes manufacturing or material defects, unless such defects have been

reported within the warranty period (item 1).

3. The equipment subject to warranty is to be brought to the place where it was purchased, or directly to the main office of the

manufacturer.

4. The warranty applies to complete equipment, accompanied by a properly filled warranty claim with a description of the defect.

5. Should the claim be accepted, the manufacturer is obliged to provide warranty repairs, at the earliest convenienve, however not later

that within 14 days from the delivery to the service centre of the manufacturer.

6. The repair period mentioned in item 5 may be prolonged, if there are no technical possibilities to carry out the repairs, or if the

equipment has been conditionally accepted, due to the breaking warranty terms by the claimant.

7. All the services rendered by force of the warranty are carried out at the service centre of the manufacturer, exclusively.

8. The warranty does not cover the defects of the equipment, resulting from:

- reasons beyond the manufacturer's control,

- mechanical damage,

- improper storage and transport,

- use that violates the operation manual or equipment’s intended use

- fortuitous events, including lightning discharges, power failures, fire, flood, high temperatures and chemical agents,

- improper installation and configuration (in defiance with the manual),

9. The warranty is void in any of the following circumstances:

- construction changes

- repairs carried out by any unauthorized service center

- damage or removal of warranty labels

- modifications of the serial number

10. The liability of the manufacturer towards the buyer is limited to the value of the equipment, determined according to the wholesale

prices suggested by the manufacturer on the day of purchase.

11. The manufacturer takes no reponsibility for the defects that result from:

- the damaging, malfunctioning or inability to operate the equipment

- defects that result from using the equipment outside its stated specifications and operating parameters failing to abide by the

recommendations and requirements contained in the manual, or the use of the equipment.

Pulsar K.Bogusz Sp.j.

Siedlec 150, 32-744 Łapczyca, Poland

Tel. (+48) 14-610-19-40, Fax. (+48) 14-610-19-50

e-mail: biuro@pulsar.pl sales@pulsar.pl,

http:// www.pulsar.pl, www.zasilacze.pl

Produkt Specifikationer

Mærke:	Pulsar
Kategori:	Batterioplader
Model:	PSD12020

Har du brug for hjælp?

Hvis du har brug for hjælp til Pulsar PSD12020 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Batterioplader Pulsar Manualer

Pulsar PSD12020 Manual

28 August 2024

Batterioplader Manualer

Nyeste Batterioplader Manualer

Watson MDC-3418 Manual

13 August 2025

Watson DLCX Manual

13 August 2025

Watson MDC-1544 Manual

13 August 2025

Makita BL4020 Manual

11 August 2025

Makita ADP001G Manual

11 August 2025

Nedis WDCHAQ15W110BK Manual

11 August 2025

Nedis EVCA11KWBK50 Manual

11 August 2025

Hager XEV601C Manual

10 August 2025

Hager XEV426 Manual

9 August 2025

Hager XEV202 Manual

9 August 2025