Pyle PLMRB38B.5 Manual

Pyle Ikke kategoriseret PLMRB38B.5

Læs gratis den danske manual til Pyle PLMRB38B.5 (16 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 10 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 5.5 anmeldelser. Har du et spørgsmål om Pyle PLMRB38B.5, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/16

Marine Stereo Receiver Power Amplifier

AM/FM/MP3/USB/AUX/SD Card Reader Marine

Stereo Receiver, Single DIN, 30 Preset Memory Stations,

LCD Display with Remote Control

www.PyleUSA.com

INSTALLATION

Preparation

The preparation kit is necessary to mount the radio on the dashboard, this kit is

available at electronics stores and car audio specialists, check the installation kit

before using it to make sure it is the right one for your vehicle.

INSTALL THE DEVICE

1. Lift the left or right top corner of the plastic outer trim ring

then pull it out to remove it.

2. Insert the two bracket keys into the left and right side of

the chassis to separate the chassis from the housing.

3. Install the mounting knob on the board. Check the

opening size of the sliding panel to be mounted. If the

measurement is not large enough, carefully cut it until it

slips easily on the opening. Do not force the handle in the

opening so as not to bend it. Locate the series of dubbing

tabs above, below and all sides to be mounted. Completely

insert it to the opening of the board, bend the tabs as

necessary towards outside to ensure it ts the board.

4. Slide the stereo into the opening in the dash, ensuring that

the wires behind are tucked and not pinched.

5. Follow the wiring diagram carefully.

Verify you’ve connected them correctly.

CAUTION! Connect the unit to a 12 Volt power source

with adequate ground.

6. Now that your wires are all completed, attach the front

panel and turn the unit (the vehicle must be switched on). If the unit does not ON

work, check the calibration again until the problem is solved. With the new car

stereo secured into the bracket, all you need to do is plug the wiring harness back

into the stereo and put the assembly back into place.

7. Slide the stereo into the opening in the dash, ensuring that the wires behind are

tucked and not pinched. Sometimes this may take a few times when the vehicle

has a tight dash opening. Tuck the wires back into an opening behind the unit.

8. Install the plastic outer trim ring

9. Snap all the pieces of trim back into place over the stereo. Double check that all

screws and trim pieces are securely in place.Try out the new stereo. Turn the car

power on again and play around with the stereo and its settings to be sure

everything is in working order.

Produkt Specifikationer

Mærke:	Pyle
Kategori:	Ikke kategoriseret
Model:	PLMRB38B.5

Har du brug for hjælp?

Hvis du har brug for hjælp til Pyle PLMRB38B.5 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Pyle Manualer

Pyle PLMRKT2A Manual

4 Juni 2025

Pyle PDWM2950 Manual

12 Januar 2025

Pyle PVCLG85 Manual

9 Januar 2025

Pyle PSCBLKIT22 Manual

1 Januar 2025

6 December 2024

6 December 2024

21 Oktober 2024

27 September 2024

26 September 2024

26 September 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Planet XGPN-100 Manual

15 Juni 2025

Proficook PC-EKA 1283 Manual

15 Juni 2025

OmniMount OBSP8 Manual

15 Juni 2025

Levenhuk FS10 Manual

15 Juni 2025

Vestil PM4-2148-LP Manual

15 Juni 2025

ElectriQ STRV-W1-B Manual

15 Juni 2025

Adler AD 4521 Manual

15 Juni 2025

AMX HydraPort HPX-AV102 Manual

15 Juni 2025

Hughes & Kettner Red Box Mk II Manual

15 Juni 2025

Hughes & Kettner Quantum QC 412 Manual

15 Juni 2025