Qtx Tetra Bubble Manual

Qtx Effektmaskine Tetra Bubble

Læs gratis den danske manual til Qtx Tetra Bubble (3 sider) i kategorien Effektmaskine. Denne vejledning er vurderet som hjælpsom af 3 personer og har en gennemsnitlig bedømmelse på 3.8 stjerner ud af 2 anmeldelser. Har du et spørgsmål om Qtx Tetra Bubble, eller vil du spørge andre brugere om produktet?

Side 1/3
www.avsl.com 160.553UK Manual
Tetra Bubble
High Output 4-Wheel Bubble Machine
Item ref: 160.553UK
User Manual
Introduction
Thank you for choosing the Tetra Bubble machine as part of your stage effects setup. This machine is a high
output, compact model and will provide consistent large area coverage. Please read and keep this manual to
ensure maximum performance and avoid damage through misuse.
Unpacking
Your Tetra Bubble should reach you in good condition and should be supplied with IEC mains lead(s), a wired
remote-control sensor and keyfob remote. If there are any signs of damage or items missing from the
packaging, contact your dealer immediately.
Warning
To prevent risk of fire or electric shock, do not expose electrical parts to rain or moisture.
If liquids are spilled on the housing or through the vents, disconnect the mains, allow the unit to dry out and
have it checked by qualified personnel before further use. Avoid any impact, dropping or extreme pressure to
the housing. No user serviceable parts inside - do not open the case. Refer all servicing to qualified service
personnel.
Caution: Please read this manual carefully before operating
Damage caused by misuse is not covered by the warranty
www.avsl.com 160.553UK Manual
Placement
The Tetra Bubble has an upright fluid tank and should always be operated in an upright position. As the
output of the unit is vertical up to a height of 5m, ensure there is adequate space for the bubble flow. Allow
easy access to the rear panel and the bubble fluid tank for refilling and cleaning. When moving the unit
around, take care not to spill the contents of the tank inside the machine and always try to keep the mains
connection and lead dry at all times.
Safety
Check for correct mains voltage and condition of IEC lead before connecting to power outlet.
Check the condition of the remote lead and ensure that it is not trapped.
This unit must be earthed.
Cleaning
Use a soft dry or slightly damp cloth to clean the casing.
Do not use strong solvents for cleaning the unit.
Empty contents and rinse the bubble fluid tanks after each use.
Setting up
The Tetra Bubble uses bubble fluid to produce the effect.
It is recommended to use qtx bubble fluid for best results (160.574UK, 160.575UK).
For bubbles that glow in UV light, qtx UV bubble fluid may be used (160.576UK, 160.577UK).
Remove the fluid tank from the unit and fill with the required fluid.
Return the tank to the unit and ensure the filling tubes are correctly replaced into the hole in the top of
the bottle and pushed down fully into the liquid.
Connect the supplied wired remote control to the female IEC on the rear panel.
Connect the IEC mains plug to the mains and switch on.
Rear panel


Produkt Specifikationer

Mærke: Qtx
Kategori: Effektmaskine
Model: Tetra Bubble

Har du brug for hjælp?

Hvis du har brug for hjælp til Qtx Tetra Bubble stil et spørgsmål nedenfor, og andre brugere vil svare dig




Effektmaskine Qtx Manualer

Qtx

Qtx FogoSphere Manual

8 Oktober 2025
Qtx

Qtx Tetra Bubble Manual

7 Oktober 2025
Qtx

Qtx VertiBox Manual

7 Oktober 2025
Qtx

Qtx HZ-1500LED Manual

3 April 2024
Qtx

Qtx QTFX-LBF1 Manual

19 Januar 2024
Qtx

Qtx SW-2 Manual

10 December 2023
Qtx

Qtx QTFX-B4 Manual

3 Juni 2023
Qtx

Qtx ZEPHYR Manual

21 December 2022
Qtx

Qtx QTFX-900 Manual

29 November 2022

Effektmaskine Manualer

Nyeste Effektmaskine Manualer