Quasar Science Single Spectrum T8 Manual

Quasar Science Ikke kategoriseret Single Spectrum T8

Læs gratis den danske manual til Quasar Science Single Spectrum T8 (1 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 26 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 13.5 anmeldelser. Har du et spørgsmål om Quasar Science Single Spectrum T8, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

QUASAR SCIENCE

Questions? info@quasarscience.com (800) 876-0665 Questions? info@quasarscience.com (800) 876-0665

Quasar Science 687 S. Anderson St., Los Angeles, CA 90023

Single Spectrum T8

Installation Instructions

Warning: To reduce the risk of fire and electrical shock, do not remove the retrofit

LED tube lamp enclosure (cover and caps).

•No user-serviceable parts inside. Refer servicing to qualified service personnel

•DO NOT EXPOSE THIS APPARATUS TO RAIN.

•LUMINAIRE CONVERSION, RETROFIT.

•FOR USE ONLY WITH FLUORESCENT LUMINAIRES IDENTIFIED IN MANUFACTURER'S

INSTRUCTIONS

•THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE

INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND

OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.

•For the 120VAC version lamp, determine if the power source provides 120VAC. For the 240VAC

version lamp, determine if the power source is 220-240VAC.

•Luminaires wiring, ballasts, or other electrical parts may be damaged when drilling for

Installation of reflector kit hardware. Check for enclosed wiring and components.

•LED tube installation requires knowledge of fluorescent lighting luminaires electrical systems.

If not qualified, do not attempt installation. Contact a qualified electrician.

•Install this kit only in the luminaries that has the construction features and dimensions shown

in the photographs and/or drawings and where the input rating of the LED tube does not

exceed the input rating of the luminaire.

•To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other

sharp objects. Do not make or alter any open holes in an enclosure of wiring or electrical

components during kit installation.

•Do not use this LED tube in luminaires employing shunted bipin lampholders. Note: Shunted

lamp holders are found only in fluorescent luminaires with InstantStart ballasts. Instantstart

ballasts can be identified by the words “Instant Start” or “I.S.” marked on the ballast. This

designation may be in the form of a statement pertaining to the ballast itself, or may be

combined with the marking for the lamps with which the ballast is intended to be used, for

example F40T12/IS. For more information, contact the LED luminaire manufacturer.

•Installers should not disconnect existing wires from lampholder terminals to make new

connections at lampholder terminals. Instead installers should cut existing lampholder leads

away from the lampholder and make new electrical connections to lampholder lead wires by

employing applicable connectors.

QUASAR SCIENCE

Quasar Science 687 S. Anderson St., Los Angeles, CA 90023

Single Spectrum T8

Installation Instructions

*Caution - Risk of Electric Shock – Use In Dry Location.

*End retrofit luminaire has been modified and can no longer operate the originally intended lamp.

*This device is not intended for use with emergency exit fixtures or emergency exit lights.

*The luminaries shall be installed by an electrician.

INSTALLATION INSTRUCTIONS

1. Disconnect all power to the lamp fixture.

2. Take off the fluorescent lamp.

3. Remove the ballast and starter where applicable and remove the leads from the connector

where no use.

4. Designate one side of the fixtures lamp sockets as the “LIVE END” and mark for future

reference.

X: Cut Wire

Fluorescent tube

G13 Lamp holder G13 Lamp holder

Junction Box Electric Ballast

120-277VAC

Step 1

LED Light Tube

G13 Lamp holder G13 Lamp holder

Junction Box Electric Ballast

120-277VAC

Step 2

5. Connect the line lead to one of the two wires connected to the lamp pin base and connect

the neutral lead to the second of the two wires connected to the same lamp pin base (above),

and the lamp pin L to connect lamp base positive lead，the lamp pin N to connect lamp base

negative lead.

*For any 1,2,3,bulb fixture, simply connect all the line leads from each lamp pin bases to the

line lead in and connect all the neutral leads from each lamp pin bases to the neutral lead in.

6. After modification completes, then affix the Lamping Replacement Marking label and

cautionary label to painted surface and bare aluminum , located this where visible during

relamping on the retrofitted luminaire.

For Operations Manual and Photometrics,

visit QuasarScience.com/support

Produkt Specifikationer

Mærke:	Quasar Science
Kategori:	Ikke kategoriseret
Model:	Single Spectrum T8

Har du brug for hjælp?

Hvis du har brug for hjælp til Quasar Science Single Spectrum T8 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Quasar Science Manualer

Quasar Science Single Spectrum T8 Manual

12 Marts 2025

Quasar Science Q-Lion Q5 Manual

12 Marts 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

KoolStar Starter 950 Manual

25 December 2025

VOX SETSF5702B Manual

25 December 2025

Yamazen SUC-202 Manual

25 December 2025

Vaxcel OW37081 Manual

25 December 2025

Vaxcel T0253 Manual

25 December 2025

Reelcraft L 4525 123 7A Manual

25 December 2025

Reelcraft L 5700 Manual

25 December 2025

Viewsonic ViewBoard IN8621C Manual

25 December 2025

Yamazen YTY-A410 Manual

25 December 2025

BlaknBlu Oscar DSF Manual

25 December 2025