Rain Bird ESP-LXME2 Manual

Rain Bird Joystick ESP-LXME2

Læs gratis den danske manual til Rain Bird ESP-LXME2 (91 sider) i kategorien Joystick. Denne vejledning er vurderet som hjælpsom af 12 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 6.5 anmeldelser. Har du et spørgsmål om Rain Bird ESP-LXME2, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/91

LXME2

Series Controllers

Installation, Programming & Operation Guide

CAUTION:

This appliance is not intended for use by persons (including children) with

reduced physical, sensory or mental capabilities, or lack of experience and

knowledge, unless they have been given supervision or instruction concerning

use of the appliance by a person responsible for their safety.

Children should be supervised to ensure that they do not play with the

appliance.

For controllers not provided with supply cord, the xed installation must

include a disconnecting device for all three poles suitable for overvoltage

category III protection.

WARNING:

The LXME2 controller must be properly surge protected and grounded. Doing

so can help prevent damage to the controller and irrigation system and also

signicantly reduce troubleshooting, repair time and expense. Failure to do so

could result in failure of your controller and voiding the warranty.

Electric shock can cause severe injury or death. Make sure power supply is

turned OFF before connecting power wires.

All electrical connections and wiring runs must be made according to local

building codes.

The current date and time on the controller is retained by a long-life lithium

battery, which must be disposed of in accordance with local regulations.

This controller uses a non-replaceable lithium battery. Lithium batteries

are hazardous and can cause severe or fatal injuries in 2 hours or less if it is

swallowed or placed inside any part of the body. Medical attention should be

sought immediately if this is suspected. Keep batteries away from children

Current Section: Contents 2

Navigation:

CONTENTS

1. INTRODUCTION .............................................................................................5

1.1 LXME2 Controller Overview 5 .......................................................................................................

1.2 Controller Features 5 .....................................................................................................................

1.3 In the Box 6 ......................................................................................................................................

1.4 Regulatory Compliance 6 ..............................................................................................................

1.5 Valves (Stations) 7 ..........................................................................................................................................

1.6 Programming Overview 7 .............................................................................................................

1.6.1 Programs .............................................................................................................................................................7

1.6.2 Storing the Quick Start Guide 7 ............................................................................................................................

1.6.3 Remote Programming 7 ........................................................................................................................................

1.7 Interface Overview 8 ......................................................................................................................

1.8 Programming Checklist 9 ..............................................................................................................

1.8.1 Set Up Hardware 9 .................................................................................................................................................

1.8.2 Set Up Programs 9 .................................................................................................................................................

1.8.3 Set Up Advanced Programming (Optional) 9 ...................................................................................................................

1.8.4 Review Setup 10 .....................................................................................................................................................

1.8.5 Additional Advanced Programming (Optional) 10 ........................................................................................................

2. 11 AUTO ....................................................................................................

2.1 Alarms ....................................................................................................................................... 12

3. Set Date/Time 13 ......................................................................................

4. Setup 14 ....................................................................................................

4.1 Master Valves 14 ............................................................................................................................

4.2 Weather Sensors 20 .......................................................................................................................

4.3 Station Setup 21 ............................................................................................................................

4.3.1 Station Priority 21 ..................................................................................................................................................

4.3.2 Master Valves/ Pumps 22 ......................................................................................................................................

4.3.3 Weather Sensors 22 ...............................................................................................................................................

4.3.4 Valves Per Station 23 .............................................................................................................................................

4.3.5 Flow Sensors - Models only 23 ....................................................................................................................................

4.4 Advanced Station Settings 27 ......................................................................................................

4.4.1 Cycle + Soak (Advanced Station Settings) 27 ....................................................................................................................

4.4.2 Copy Station To Station 28 ....................................................................................................................................

4.4.3 Station Delay (Advanced Station Settings) 28 ..................................................................................................................

4.4.4 SimulStations (Advanced Station Settings) 29 ..................................................................................................................

4.4.5 Station Sequencing (Advanced Station Settings) 30 .......................................................................................................

4.4.6 Module/ Station Numbering (Advanced Station Settings) 32 ......................................................................................

5. Set Start Times 33 .....................................................................................

6. Run Times 34 ...............................................................................................