Rane MS 1 Manual

Rane Ikke kategoriseret MS 1

Læs gratis den danske manual til Rane MS 1 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 17 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 9 anmeldelser. Har du et spørgsmål om Rane MS 1, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Data Sheet-1

MS 1

MICROPHONE STAGE

Parameter Specification Limit Units Conditions/Comments

Input Impedance 1k 1% W Balanced 500 + 500

Gain Range +21.5 to +60 1.5 dB

Phantom Power +48 4% VDC DIN 45596 & IEC 268-15

Max Input Level 0/-38 1 dBu 21.5/60 dB gain

Equivalent Input Noise -130/-117 2 dBu 20k BW, 60/21.5 dB gain, Rs=150 ohms

Signal-To-Noise Ratio 102/75 (re +4 dBu) typ dB 20k BW, 21.5/60dB gain

Frequency Response 20-20 kHz 0.1 dB -3 dB @ 130/90 kHz, 21.5/60 dB gain

THD+Noise 0.007/.03 .001 % +20 dBu, 20-20 kHz, 21.5/60 dB gain

IM Distortion (SMPTE) 0.008 .002 % 60 Hz/7 kHz, 4:1, +20 dBu

Slew Rate 6 1 V/µs Fully symmetrical

Max Output Level +20 1 dBu Balanced out, 600 ohms

Output Impedance 50 1% W Balanced

Output Cable Length 1000' (305 m) typ Belden 8451 or equivalent

Unit: Agency Listing

..........120 VAC model Class 2 Equipment National Electrical Code

UL & CSA Exempt Class 2 equipment

..........230 VAC model CE-EMC EMC directive 89/336/EEC

CE-Safety Exempt per Art. 1, LVD 73/23/EEC

Power Supply: Agency Listing Class 2 Equipment

..........120 VAC model UL File no. E88261

CSA File no. LR58948

..........230 VAC model CE-EMC EMC directive 89/336/EEC

CE-Safety LV directive 73/23/EEC

..........100 VAC model Built to JIS Japan only

Power Supply Input 18 VAC w/center tap 10% Vrms Rane RS 1 supplied with MS 1

Max Current Consumption 220 mA

Unit Size 1.65" H x 5.1" W x 4.25" D (4.2 cm x 13 cm x 10.8 cm)

..........Weight 1 lb (0.45 kg)

Shipping Size 3.6" H x 11.75" W x 7.2" D (9.5 cm x 30 cm x 18 cm)

..........Weight 4 lb (1.8 kg)

General Description

The Rane MS 1 Mic Stage preamplifier provides the

answer when you need just one microphone input in an

otherwise line-level world. Give us a call to go from either a

dynamic, condenser or electret microphone to a line level

input with a minimum of noise, distortion, cost and hassle.

The MS 1 provides 48 V switchable Phantom Power with

indicator LED, continuous rotary Gain trim between 21.5 dB

and 60 dB, overload LED, and XLR balanced Input & Output

connectors. A Phase Invert switch and high-current cross-

coupled output line drivers round out the features.

The MS 1 utilizes one of the finest ultra low noise

amplifier designs available. Featuring a true differential input

with high common-mode rejection, use of the MS 1 guaran-

tees performance usually found only in mixing consoles

costing thousands of times as much. Of course, for all of that

extra money you receive a proportional increase in KPSI

(knobs per square inch).

Features

• Gain Control with Overload Indicator

• Phase Invert Switch

• Switchable 48V Phantom Power

• Ultra Low Noise Design

DATA SHEET

• True Differential Input

• Cross-Coupled Line Driver

• UL/CSA/CE and 100/120/230 VAC Remote Power Supply

Data Sheet-2

All features & specifications subject to change without notice DOC 103169 PN 08037 2-98

MS 1

MICROPHONE STAGE

Application Information

Uses and applications for the MS 1 should be obvious. But

then again, its obvious to us our taxes are too high and

nothing is being done about that. With this in mind, perhaps a

few words on using the MS 1 might not be wasted.

BALANCED USE

The MS 1 provides a true cross-coupled balanced Output.

This is equivalent to an electronic simulation of a transformer

output. Rane follows the AES standard of pin 2 = hot.

When running a long cable back to the mixer, run a line

level balanced line rather than a mic level line. The compact

MS 1 can mount closer to the microphone, provide a local

volume control (or not, just pull the knob off), while the

stronger signal minimizes RF and hum irritations.

UNBALANCED USE

Balanced use is recommended to minimize noise. When

you must drive an unbalanced device with the MS 1's bal-

anced Output, connect pin 2 to the “+” or “hot” lead, and tie

pin 3 and ground together at the shield.

MIXING

The MS 1 is designed to fill the need for adding one or

two microphone channels to line level mixers, such as the

Rane SM 26B or SM 82. Many installations using either of

these products invariably wind up with one unused input that

would do the job perfectly if only it could operate at mic

level. In rides the MS 1 to the rescue.

DIGITAL RECORDING AND SAMPLING

Another handy use for the MS 1 is in recording applica-

tions. Many popular products do not have a high enough

quality mic preamp to suit the resolution of the digital

processing electronics! Such irony. Using the ultra low noise

MS 1 to bring the mic inputs up to extremely high quality line

level is an easy and affordable solution for this dilemma. No

garbage in; no garbage out. Clippity-clop; clippity-clop.

Block Diagram

©Rane Corporation 10802 47th Ave. W., Mukilteo WA 98275-5098 TEL (425)355-6000 FAX (425)347-7757 WEB http://www.rane.com

MICROPHONE TYPES

The available gain range of the MS 1 allows the use of

virtually any type of microphone. True 48V phantom power

guarantees the MS 1 works with every microphone made. The

better the mic, the better the MS 1 sounds.

Ah, the sound of the thundering hoofs is deafening.

Architectural Specifications

The microphone preamplifier shall be a single channel

stand-alone unit with remote power supply. The power supply

shall be U.L. listed, C.S.A. certified, and CE certified. The

input and output shall be fitted with XLR connectors. A

polarity inverting switch shall be included. Phantom power

shall be provided in compliance with DIN 45596 & IEC 268-

15 and be controlled by a slide switch with an LED indicator.

A gain control shall be provided with 21.5-60 dB adjustment

range. A power indicator and a system overload indicator

shall be provided. High current cross-coupled active output

line driver shall be standard, as well as input RFI filter

protection.

The unit shall be a Rane MS 1 Microphone Stage.

CHASSIS GROUNDING

Units with outboard power supplies do not ground the

chassis through the line cord. Make sure that these units

are grounded either to another chassis which is earth

grounded, or directly to the grounding screw on an AC

outlet cover by means of a wire connected to a screw on

the chassis with a star washer to guarantee proper contact.

Please refer to RaneNote 110, “Sound System Inter-

connection” (supplied in your manual and available on

request separately) for further information on system

grounding.

Produkt Specifikationer

Mærke:	Rane
Kategori:	Ikke kategoriseret
Model:	MS 1

Har du brug for hjælp?

Hvis du har brug for hjælp til Rane MS 1 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Rane Manualer

22 Juni 2025

22 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

20 Juni 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

BSS Audio FCS-926 Manual

14 September 2025

Brandson 303842 Manual

14 September 2025

AMX DGX-O-DXF-MMS Manual

14 September 2025

Brandson 304024 Manual

14 September 2025

JILONG JL097109NPF Manual

14 September 2025

Brandson 303403 Manual

14 September 2025

AMX DVX-2250HD Manual

14 September 2025

AMX Vision² Manual

14 September 2025

AMX NMX-ENC-1100 Manual

14 September 2025

AMX UPC20+ Manual

14 September 2025