Rane MX 22 Manual

Rane Ikke kategoriseret MX 22

Læs gratis den danske manual til Rane MX 22 (11 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 25 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 13 anmeldelser. Har du et spørgsmål om Rane MX 22, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/11

Manual-1

QUICK START

Whoa, hold on there. Even if you don’t read manuals as a matter of principle, at least read this section to avoid hurting

yourself or your equipment.

Connect the MX 22 with the power off. Balanced XLR cables are recommended, but if you must convert to ¼" connec-

tors, buy or make a cable like the ones on page Manual-11 and keep them as short as possible. This device uses low imped-

ance balanced line drivers. Do not connect the “+” or “–” output pins to ground, as this may cause the power supply to

shut down. For unbalanced use, leave the unused output pin (“+” or “–”) unterminated.

Consult the speaker manufacturer for the correct crossover FREQUENCY setting. As rugged as some drivers are, many

(especially compression drivers) will not accept frequencies outside of their normal range without producing distortion and

possibly self-destruction.

With all equipment turned off and LEVEL controls down, begin making connections to the system as shown on page

Manual-4 or 5. When turning on the system, switch on the power amplifiers last. Now, feed the MX 22 some program

material. Start by turning up the LOW LEVEL and HIGH LEVEL to the 0 dB marks. Slowly increase the INPUT

LEVEL, even if it goes all the way to 10, so the +4 dBu (green) light blinks occasionally and the OL (red) light stays out.

This delivers the best signal-to-noise performance.

The MONO SUB OUTPUT is a sum of the Left and Right Low Outputs. The MONO SUB LEVEL adjusts only this

Output and is not affected by the LOW LEVEL control.. When using a single subwoofer along with full-range cabinets

that have internal crossovers, set the 100 Hz FILTER to OUT, allowing the front panel FREQUENCY to control the

subwoofer crossover point. When used with biamp cabinets and a subwoofer, set the 100 Hz FILTER switch to IN to

allow only frequencies below 100 Hz at this output jack. This way, the MX 22 almost does the job of a Stereo 3-Way

crossover, but without removing that awesome bass from the Left and Right Low Outputs.

WEAR PARTS: This product contains no wear parts.

OPERATORS MANUAL MX 22

STEREO 2-WAY CROSSOVER

Produkt Specifikationer

Mærke:	Rane
Kategori:	Ikke kategoriseret
Model:	MX 22

Har du brug for hjælp?

Hvis du har brug for hjælp til Rane MX 22 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Rane Manualer

22 Juni 2025

22 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

20 Juni 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Nedis CKAA2400BK Manual

2 November 2025

Beverage-Air Horizon HFPS1HC-1G Manual

2 November 2025

Beverage-Air Horizon HFS3HC-1S Manual

2 November 2025

Beverage-Air Horizon HF1HC-1HG Manual

2 November 2025

Beverage-Air WTFCS84HC-89 Manual

2 November 2025

Hendi 691311 Manual

2 November 2025

SmallRig 4523 Manual

2 November 2025

Ikea TVERSTED 204.979.71 Manual

2 November 2025

Delphi Roady2 SA10085 Manual

2 November 2025

Impact LKB-4C Manual

2 November 2025