Rane SEQ 30L Manual

Rane Ikke kategoriseret SEQ 30L

Læs gratis den danske manual til Rane SEQ 30L (5 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 25 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 13 anmeldelser. Har du et spørgsmål om Rane SEQ 30L, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/5

Manual-1

QUICK START

If this is your first equalizer, please do yourself and

your speakers a favor and read at least the first five

pages. “An ounce of prevention...,” and all that.

The SEQ 30L is a stereo equalizer, so adjusting

any slider affects both channels simultaneously. Begin

by setting all sliders to their center detent (0 dB), and

the INPUT LEVEL to its center detent (0 dB). Try to

make more cuts than boosts. After equalizing, use the

EQ switch to compare equalized and non-equalized

signal. While EQ is switched to ACTIVE (out), adjust

the INPUT LEVEL to the same level as when EQ is

switched to BYPASS (in).

You may use either the XLR or ¼" connectors for

Inputs or Outputs. Connect only one INPUT type per

channel. The XLR and ¼" TRS inputs do not sum.

You may, however, use both types of OUTPUTS

simultaneously if desired.

WEAR PARTS: This product contains no wear parts.

OPERATORS MANUAL

SEQ 30L

STEREO GRAPHIC EQUALIZER

Manual-2

EQ BYPASS switch

When pressed to BYPASS, the filter sliders have no effect. Since actual unity

gain depends on varying slider settings, use the BYPASS switch to determine the

unity gain position of the INPUT LEVEL control by comparing ACTIVE and

BYPASS volumes.

Filter level slide controls

Each of these sliders control the

output level of both channels of the 30

bandpass filters. Center position is

grounded for guaranteed flat response.

Cable Wiring

In agreement with IEC and AES/ANSI standards, XLR wiring convention is pin

2 Positive (hot), pin 3 Negative (cold), and pin 1 Signal ground (for unbalanced

use). Pin 1 and the connector case or shell are tied to chassis ground.

INPUT LEVEL control and indicators

This controls the overall level. 0 dB gain is reached at the center detent with all

sliders centered at their 0 dB detents. Set the INPUT LEVEL to give equal volumes

with the EQ switched to ACTIVE or BYPASS, after setting the sliders (see EQ

BYPASS switch below). Apply sufficient signal to the input to occasionally light

the +4 dBu indicator. Flashing of the OL (overload) LED during peaks can be

avoided by turning the INPUT LEVEL or boosted Filters down.

Produkt Specifikationer

Mærke:	Rane
Kategori:	Ikke kategoriseret
Model:	SEQ 30L

Har du brug for hjælp?

Hvis du har brug for hjælp til Rane SEQ 30L stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Rane Manualer

22 Juni 2025

22 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

20 Juni 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

BSS Audio FCS-926 Manual

14 September 2025

Brandson 303842 Manual

14 September 2025

AMX DGX-O-DXF-MMS Manual

14 September 2025

Brandson 304024 Manual

14 September 2025

JILONG JL097109NPF Manual

14 September 2025

Brandson 303403 Manual

14 September 2025

AMX DVX-2250HD Manual

14 September 2025

AMX Vision² Manual

14 September 2025

AMX NMX-ENC-1100 Manual

14 September 2025

AMX UPC20+ Manual

14 September 2025