Rane TTM 52 Manual

Rane Ikke kategoriseret TTM 52

Læs gratis den danske manual til Rane TTM 52 (8 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 6 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 3.5 anmeldelser. Har du et spørgsmål om Rane TTM 52, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/8

Manual-1

Quick Start

Rane would like to thank you for se-

lecting the TTM 52 Performance Mixer.

The TTM 52 is one of the top performance

mixers available. It features the same high

quality components, reliability and perfor-

mance as the Rane TTM 54 mixer with a

reduced feature set (see the comparison chart on

the last page of the Data Sheet, contained in this

manual.) For experienced turntablists, the operation of

the TTM 52 will be very familiar, however, the TTM 52 has

some unique features. These new features will be mastered more

quickly if you read the entire manual. Right! We know some of you

can’t resist jumping right in, so please read at least this portion of the manual.

It will help you get a good start and learn how to properly care for your faders.

• GAIN TRIM: These controls are intended to set the signal level before the Crossfader. Always set the GAIN TRIM

controls to indicate an average signal level of +4 on the meter with the Program Faders set to maximum. Never use the

GAIN TRIM controls to set the output level. Always use the MASTER LEVEL control to set the output level. This is a

very simple thing, yet makes a huge difference in the performance of your mixer.

• PHONES: The headphone output of the TTM 52 is a high power output stage (unlike most you have used before). There

are some notable differences…

• The headphone output of the TTM 52 delivers very high volume into your headphones.

• To avoid pain, never put headphones on your head and plug them in.then

•Always start with the PHONES LEVEL turned down and then turn it up to the desired level.

• Because of the high current and low output impedance, never short one side to ground or short left and right

together as is possible with mono cup headphones. Note: Low power headphone stages typically use large

resistors on their outputs, which allow shorting, but prevent high power. The TTM 52 gives you high power but

does not allow shorting.

• MIC LEVEL: For best performance, keep this control at 0 when not in use.

• For instructions on rotating Phono/Line switches to the desired location, see page Manual-6.

• Do not spray cleaner or lubricant into the front of the Program Faders or Crossfader. The fluid will just run out the

bottom of the unit. Never use unapproved cleaner or lubricants such as skateboard wheel lube, as corrosive damage may

result, voiding the warranty. See page Manual-6 for cleaning and replacement instructions and cleaner recommendations.

•Never connect anything except an RS 1 or other approved Rane AC power supply to the thing that looks like a telephone

jack on the rear. This is an 18 VAC center-tapped power unit. Consult the Rane factory for replacement or substitution.

•WEAR PARTS: This product contains the following wear parts subject to the ninety (90) day warranty period described on

page Service-1: FT 45 Active Crossfader & Channel Fader Assembly(3); ST 1 Phono/Line Switch Assembly (2).

TTM 52

MOJO PERFORMANCE MIXER

OPERATORS MANUAL

Manual-2

  PGM 1 and PGM 2 input GAIN TRIM controls are used to adjust input level. With the Program Faders (see ) at

maximum, set controls to give a peak reading of +4 on the meter. Set the Master Level to minimum while adjusting). It is

always best to run the input level at +4 to +7. Use the MASTER LEVEL (see ) control to adjust the volume at the

MASTER OUT (see ).

 BASS and TREBLE controls provide ±12 dB of EQ for PGM 1 and PGM 2. The graph shown in

Figure 1 indicates the response of the filters.

 BALANCE controls are used for LEFT/RIGHT balance of PGM 1 and PGM 2 or for LEFT/RIGHT Pan effect. Push the

control to the left and sound moves to the left channel. Push the control to the right and sound moves to the right channel.

 PHONO / LINE source select switches are provided for PGM 1 and PGM 2. These are “clickless” switches suitable for

“transform scratch” applications. The switches are field replaceable and may be rotated in 45° increments. See Figure 4 on

page Manual-6 for rotation and replacement instructions.

 HAMSTER switches are provided for PGM 1 and PGM 2 Program Faders. These switches reverse the operation of the

adjacent Program Fader. When engaged, signal is off with the Program Fader up, and maximum with the Program Fader

down.

 Program Fader controls for PGM 1 and PGM 2 are ultra low noise, long-life, monorail devices. An ActiveFader™ design

completely isolates the control element from the audio, providing the highest reliability and performance. See page

Manual-6 for cleaning and replacement instructions.

Figure 1. Bass & Treble Controls

Produkt Specifikationer

Mærke:	Rane
Kategori:	Ikke kategoriseret
Model:	TTM 52

Har du brug for hjælp?

Hvis du har brug for hjælp til Rane TTM 52 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Rane Manualer

22 Juni 2025

22 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

20 Juni 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

JILONG JL097205NPF Manual

14 September 2025

Brandson 306570 Manual

14 September 2025

Nedis PIM30012EGY Manual

14 September 2025

Neutrik SCD-W Manual

14 September 2025

BSS Audio FCS-926 Manual

14 September 2025

Brandson 303842 Manual

14 September 2025

AMX DGX-O-DXF-MMS Manual

14 September 2025

Brandson 304024 Manual

14 September 2025

JILONG JL097109NPF Manual

14 September 2025

Brandson 303403 Manual

14 September 2025