Rangemaster LU9852 Manual

Rangemaster Køkkenvask LU9852

Læs gratis den danske manual til Rangemaster LU9852 (4 sider) i kategorien Køkkenvask. Denne vejledning er vurderet som hjælpsom af 16 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 8.5 anmeldelser. Har du et spørgsmål om Rangemaster LU9852, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

Instructions for Cubix, Cubix Gemini & Lunar

COMPOSITE INSET SINKS

WITH FIXED POSITION CLIPS

Installation Instructions

Aftercare Information

INSTALLATION

Installer

Please leave this leaet with the user, as it contains valuable

after care advice.

Notes

 During installation, take care to protect the sink

from scus and scratches.

 Avoid straining and overtightening of all plumbing

xtures connected to the sink.

 Carefully check that the moulding and edges of the

sink are dead level so that water will ow o the

drainer.

 We recommend that the worktop opening is sealed

using waterproof sealant, paint or a similar material.

 The clamping brackets are suitable for worktops of

between 28–40 mm thickness. If your worktop is a

dierent size then it may require packing under the

clips or rebating.

Preparing the Worktop

Marking out the opening

We recommend that you t the inset sink to the worktop

before permanently xing the worktop to the cabinet.

1. Place the sink upside down on the worktop. Position

the sink on the worktop as required. Make sure the

cabinet framework will clear all parts of the sink. Using a

soft, sharp pencil draw around the sink as accurately as

possible (Fig.1). Remove the sink.

Alternatively, you can use a sink template. For details go

to www.rangemaster.co.uk.

2. Draw another line 10mm inside the sink top outline –

this is the cutting line for the opening (Fig.2).

3. Drill as large a hole as possible inside the cutting line.

Using a padsaw, jigsaw or similar, cut out the opening

up to the cutting line.

Preparing the sink

Drilling a taphole

 Before drilling please read safety instructions

supplied with hole saw.

 The front face must be fully supported to prevent

cracking when drilling or cutting.

 WARNING!

Composite sink products include a silica ller. Any

machining operation will produce ne particles of

dust. Drilling or cutting be carried out in a MUST

well-ventilated area.

Worktop

Final position

of sink

Cutting line for opening

10 mm

Fig.1

Fig.2

Due to our policy of continual improvement, we reserve the right to change specications without prior notice.

Fig.3

Fig.4

Produkt Specifikationer

Mærke:	Rangemaster
Kategori:	Køkkenvask
Model:	LU9852
Bredde:	985 mm
Dybde:	508 mm
Produktfarve:	Sølv
Pakkevægt:	13500 g
Pakkedybde:	2550 mm
Pakkebredde:	6500 mm
Pakkehøjde:	1100 mm
Installationsrum bredde:	964 mm
Installationsrum dybde:	487 mm
Første skål, dybde:	180 mm
Anden skål, dybde:	110 mm
Første skål, dimensioner (BxL):	345 x 430 mm
Anden skål, dimensioner (BxL):	160 x 430 mm
Antal vaskeskåle:	2 skåle
Vask, type:	Skylle-monteret håndvask
Vask form:	Rektangulær
Vask materiale:	Metallix
Vandhane, hul:	Ja
Drænebræt:	Ja
Vandhane inkluderet:	Ingen
Antal huller til haner:	1
Størrelse på vandhane:	35 mm