RGBlink DXP V1616 Manual

RGBlink Skifte DXP V1616

Læs gratis den danske manual til RGBlink DXP V1616 (3 sider) i kategorien Skifte. Denne vejledning er vurderet som hjælpsom af 52 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 26.5 anmeldelser. Har du et spørgsmål om RGBlink DXP V1616, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

DXP V1616 –Quick Start

Installation and cabling features

Rear Panel

Connections

2VGA Output

Step 1-Mounting

Turn off or disconnect all equipment power sources.

Step 4-RS232 In

DXP V1616 Quick Start

Rev 1.0

Page 1 of 3

Address: S603-604 Weiye Building Torch Hi-Tech Industrial Development Zone, Xiamen, Fujian Province, P.R.C

Tel: 00865925771197 Fax:00865925771202

Email: sales@rgblink.com http://www.rgblink.cn

VGA Input RS232 OUT

Power Switch

Step 3-VGA Output

VIEW SIZE THE WORLD

NOTE

This guide provides quick start instructions for an experienced installer

to set up and operate the DXP V1616.

For full installation, configuration, and operation details, please refer to

the DXP V1616 user manual, which is available at www.rgblink.com.

3RS232 IN Power IEC-3 port

Step 2-VGA Input

Use to input VGA signal from VGA

player or computer with VGA connector.

Function Button

Step 5-RS232 Out

Connect to the monitor, projector and

so on.

Connecting serial communication interface of RS232

control protocol, can connect central control device,

such as CP 2048.

Serial communication interface of multiple devices

cascading control, can connect many sets of DXP

devices.

Step 6-Power

Plug in power cord which has IEC connector, DXP

V1616 supports AC power from 85 to 264V, 50-60Hz,

which means world wide compatible.

Power On

Push power switch to ON position. LCD module on the

front panel will show RGBLINK and DXP V1616

model information, and go into self verification. For the

first setup, it is default for factory setting. User can

operate DXP V1616 through the menus on LCD panel.

Local Control Front Panel Operation

【】【】0 ~ 9 Digital button: selection button for

input and output channel, used to set video signal

input and output channel, also, can be used to number

choice of save or call saving modes.

【】0 button can also be used to shut down

the channel output.

NOTE

【】【】【】10+ , 20+ , 30+ +system function button,

means decimal.

NOTE 【】20+ can be used as UP arrow keys;

【】30+ can be used as DOWN arrow keys.

【】ALL Used as distributor selection, can set a

certain input to all outputs.

【】F1 Fast call user save mode 1;

【】F2 Fast call user save mode 2;

【】Menu Related menu includes: STATUS, RESET,

MATRIX, LOGO.

【】Mode Audio and video switching key, used to

select 3 modes, such as "Audio and video sync

switching AV", "Audio switching A", "Video

switching V", it is default for "Audio and video sync

switching AV".

【】Enter Confirm button, when functional input is

confirm button, and press Enter before enter 【】

menu, it displays the current input/output state, "/"

means empty, and not choose input signal source.

【】【】20+ , 30+ function reuse button:

Push Menu to enter the menu, press 20+ UP 【】【】

arrow keys, 30+ DOWN arrow keys, and select 【】

the menu option.

DXP V1616 Quick Start

Rev 1.0

Page 2 of 3

Address: S603-604 Weiye Building Torch Hi-Tech Industrial Development Zone, Xiamen, Fujian Province, P.R.C

Tel: 00865925771197 Fax:00865925771202

Email: sales@rgblink.com http://www.rgblink.cn

How to set one-to-one correspondence for

input and output way

1. Press button Rec on front panel;【】

2. Press button 0 on front panel;【】

3. Press Enter to confirm.【】

How to switch from one input to all outputs

1. Press button on front panel, for example, choose 2 ;【】

2. Press ALL , and finish switching input2 to all 【】

outputs.

Also, you can get the same operation effect by the

following ways:

1. Press button on front panel, for example, choose

【】ALL ;

2. Choose input way, for example, button 2 ;【】

3. Press Enter to confirm.【】

How to save pre-set input and output way

1. Press button Save on front panel;【】

2. Can select 24 modes from button 1 ~ 24 , 【】【】

for example, choose button 2 ;【】

3. Press Enter to confirm.【】

NOTE Input way: currently connect way for

switching signal;

Output way: the connect way of peripheral display

device.

【】【】1 ~ 9 button on the panel means way1 to way9.

Way above 10 can be selected combined 10+ with【】

【】【】0 ~ 6 button.

How to factory reset

How to read device related information

How to switch between input and output way

DXP V1616 can rapidly switch any way signals by front

panel buttons, specific operations are as follows:

1. Press front panel number button, select the input way,

such as choosing 3 for input way;【】

2. Press again front panel number button, select the

output way, such as choosing 5 for output way;【】

3. After selection, press Enter to confirm.【】

【】Rec Call saving mode selection key, can call saving

user mode, range for: 0 ~ 24 , a total of 25 【】【】】

kinds of call saving mode.

【】Save Saving modes selection key, can save all

current switching channels and current states, range for:

【】【】 1 ~ 24 , a total of 24 kinds of saving modes.

If power fails suddenly, the device will

automatically save to the current using mode,

and do not need reset when power on again.

NOTE

【】Esc The button exits the current state to the top

level state.

How to close one output way

1. Press button 0 on front panel;【】

2 .Choose output way, for example, button 8 ;【】

3. Press Enter to confirm.【】

How to close all output ways

1. Press button 0 on front panel;【】

2. Press button ALL on front panel. 【】

Also, you can get the same operation effect by the

following way:

1. Press button ALL on front panel;【】

2. Press button 0 on front panel;【】

3. Press Enter to confirm.【】

How to call pre-set input and output way

saving mode

1. Press button Rec on front panel;【】

2. Can select 25 modes from button 0 ~ 24 , 【】【】

for example, choose button 7 ;【】

3. Press Enter to confirm.【】

NOTE 【】O is default for one-to-one correspondence

for input and output way. That is input 1 is 【】

corresponding to output 1 , input 2 is 【】【】

corresponding to output 2 …【】

1. Press button Menu on front panel;【】

2. Press button 30+ 30+ reuse for DOWN 【】（【】

arrow key, button 20+ reuse for UP arrow 【】

key , make RESET option for selected state;）

3. Press Enter to confirm and enter the 【】

initialization interface;

4. Press any key according to the LCD hint and

complete factory reset.

1. Press button Menu on front panel;【】

2. It is default for STATUS option, if it is not selected,

press 30+ or 20+ Now 30+ reuse【】【】（【】

for DOWN arrow key, button 20+ reuse for 【】

UP arrow key and select STATUS;）

3. Press Enter to confirm, read the information【】

by button 30+ DOWN arrow key or button【】

【】20+ UP arrow key.

How to set LOGO display when power on

1. Press button Menu on front panel;【】

2. Press 30+ or 20+ Now 30+ reuse【】【】（【】

for DOWN arrow key, button 20+ reuse for 【】

UP arrow key and select LOGO;）

3. Press Enter to confirm, and enter LOGO 【】

switch setting, LOGO ON or OFF at boot can be

set.

Produkt Specifikationer

Mærke:	RGBlink
Kategori:	Skifte
Model:	DXP V1616

Har du brug for hjælp?

Hvis du har brug for hjælp til RGBlink DXP V1616 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Skifte RGBlink Manualer

RGBlink DXP D0404 Manual

20 Juni 2024

RGBlink DXP V0808 Manual

20 Juni 2024

RGBlink DXP V1616 Manual

20 Juni 2024

Skifte Manualer

Nyeste Skifte Manualer

Lancom GS-2412 Manual

4 April 2025

Lancom GS-2412P Manual

4 April 2025

Lancom GS-2426 Manual

4 April 2025

Hager ARF970D Manual

3 April 2025

Hager ARF920D Manual

3 April 2025

Roline 14.01.3579 Manual

2 April 2025

Fantini Cosmi B12BN Manual

1 April 2025

Fantini Cosmi B12DN Manual

1 April 2025

Fantini Cosmi B12GN Manual

1 April 2025

Fantini Cosmi B12HN Manual

1 April 2025