Rheem 52D300 Manual

Rheem Varmeapparat 52D300

Læs gratis den danske manual til Rheem 52D300 (64 sider) i kategorien Varmeapparat. Denne vejledning er vurderet som hjælpsom af 6 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 3.5 anmeldelser. Har du et spørgsmål om Rheem 52D300, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/64
This water heater must be installed and serviced by a qualified person.
Please leave this guide with the householder.
Owner’s Guide
and
Installation Instructions
Solar Hiline
®
Water Heater
52D Series Open Circuit
WARNING: Plumber – Be Aware
Use copper pipe ONLY. Plastic pipe MUST NOT be used.
It is a requirement of a solar water heater installation that all pipe work be in copper
and not plastic, due to the effects of high water temperatures and pressures.
An electronic copy of these Owner’s Guide and Installation Instructions can be downloaded from rheem.com.au.
PATENTS
This water heater may be protected by one or more patents or registered designs in the name of
Rheem Australia Pty Ltd.
TRADE MARKS
®
Registered trademark of Rheem Australia Pty Ltd.
™ Trademark of Rheem Australia Pty Ltd.
Colorbond
®
is a registered trademark of BlueScope Steel Limited.
Note: Every care has been taken to ensure accuracy in preparation of this publication.
No liability can be accepted for any consequences, which may arise as a result of its application.
WARNING: Plumber – Be Aware
• The solar hot and solar cold pipe work between the solar Hiline storage tank and the solar collectors
are supplied in the pipe kit. The supplied copper solar hot and solar cold pipes MUST BE used.
• If the solar water heater is installed either on a metal roof or in a trafficable area, such as on an
accessible roof, then the solar hot and solar cold pipes must be insulated. The solar hot and solar cold
pipes may be required to be insulated to comply with local regulations.
If insulation is required, the full length of the solar hot and solar cold pipes MUST BE insulated.
The insulation must:
◼ be of a closed cell type or equivalent, suitable for a solar water heating application and capable
of withstanding the temperature of the water generated by the solar collectors under stagnation
conditions
The specification of the chosen insulation material should be checked with the insulation
manufacturer prior to installation as different materials may vary in temperature tolerance
◼ be at least 13 mm thick
◼ be weatherproof and UV resistant
◼ be fitted up to and cover the connections on both the solar storage tank and the solar collectors.
The insulation will offer protection to a metal roof against corrosion due to water running off the copper
pipes, assist in avoiding accidental contact with the solar pipe work as very high temperature water
can flow from the solar collectors to the solar storage tank, and also reduce pipe heat losses.
• Plastic pipe MUST NOT be used, as it will not withstand the temperature and pressure of the water
generated by the solar collectors under stagnation conditions. Extremely high water temperatures and
extremely high water pressures can be generated under these conditions. Plastic pipe cannot
withstand these temperatures and pressures and MUST NOT be used. Failure of plastic pipe can lead
to the release of high temperature water and cause severe water damage and flooding.
• There MUST BE a continuous fall of a minimum 10° in the pipe work from the solar Hiline storage
tank to the solar collectors. The highest point of the solar cold pipe and solar hot pipe must be where
they connect to the solar Hiline storage tank, otherwise thermosiphoning will not occur.
• A non-return valve MUST BE installed on the cold water line to the solar storage tank AFTER the cold
water branch to a temperature limiting device.
• The solar water heater, including the collector circuit, is to be isolated during the testing and
commissioning of the heated water reticulation system in a building in accordance with Clause 9.3 (a)
of AS/NZS 3500.4:2018. The collector circuit includes the solar hot and solar cold pipes and solar
collectors.

Produkt Specifikationer

Mærke: Rheem
Kategori: Varmeapparat
Model: 52D300

Har du brug for hjælp?

Hvis du har brug for hjælp til Rheem 52D300 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Varmeapparat Rheem Manualer

Rheem

Rheem 52D300 Manual

12 August 2025
Rheem

Rheem Raypak Residential P0280 Manual

30 August 2024
Rheem

Rheem 561325 Manual

30 August 2024
Rheem

Rheem Solar 511161 Manual

30 August 2024
Rheem

Rheem 591270 Manual

30 August 2024
Rheem

Rheem 554325 Manual

30 August 2024

Varmeapparat Manualer

Nyeste Varmeapparat Manualer

Eurolite

Eurolite LED THA-120PC Manual

13 August 2025
Thermastore

Thermastore Heatwave270 Manual

13 August 2025
Camry

Camry CR 7827 Manual

13 August 2025
DeLonghi

DeLonghi Dragon 4 Pro TRDX40615E Manual

12 August 2025
DeLonghi

DeLonghi Dragon 4 Pro TRDX41024E Manual

12 August 2025
Tesy

Tesy CN 055 250 MIS F Manual

12 August 2025
Adler

Adler AD 6815 Manual

12 August 2025
Adler

Adler AD 7748 Manual

12 August 2025
Gasmate

Gasmate GM20-425 Manual

12 August 2025
Ivation

Ivation IVAIFWM1500 Manual

12 August 2025