Rockustics PowerRock Manual

Rockustics Ikke kategoriseret PowerRock

Læs gratis den danske manual til Rockustics PowerRock (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 20 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 10.5 anmeldelser. Har du et spørgsmål om Rockustics PowerRock, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

XT-PowerRock

INSTALL INSTRUCTIONS

Ultra-Fidelity Outdoor Speakers

Contact: MSE Audio, 855.663.5600 / 913.663.5600 / sales@mseaudio.com

Please read the following instructions carefully before install-

ing your Rockustics

Rock speaker. If you have any questions

regarding installation that are not answered in the following

directions, please contact your local sound contractor or the

Rockustics

/MSE Audio

technical support team.

Basic Wiring

(Diagram A) Locate speaker wire on the underside of the rock.

If necessary, strip the wire ends and trim the wire to the appro-

priate length. Use the supplied silicone wire nut to connect the

positive (red) leads of the speaker and input wires. Repeat this

step with the negative (black) leads. Rockustics recommends

using 14ga or heavier Direct Burial cable for the connection be-

tween the amplier and the speakers.

NOTE: The provided wire nuts are meant for permanent installa-

tion use only. If you are temporarily wiring the speakers, do not

use these wire nuts. In the event you have used the wire nuts,

and need to re-wire your system, do not attempt to unscrew the

nuts. Instead, clip the wires below the nut, and follow the steps

in the section with a new pair of waterproof wire Basic Wiring

nuts (these are available at most hardware stores).

Optimizing Speaker Placement for Best Sound

All Rockustics speakers can generate a high SPL (sound

pressure level). Be ready to rock, but be considerate of your

neighbors! Maximum acoustic performance should be an

important factor in determining speaker placement. Here is how

to achieve it:

1) Establish where the most likely or average listening

position will be.

2) The speakers should be placed at or close to the same

distance from that point.

3) The actual distance between the listening position and

the location of the speakers is not critical. However, keep

in mind that as the distance between listening area and

speaker is increased, there will be a noticeable decrease

in perceived volume.

4) Be sure to conrm amp power matches the power rating

on the speaker. Over-driving the speaker can lead to

permanent damage that is not covered under warranty.

Optimizing Aesthetics with Speaker Placement

All Rockustics products are designed with a boost in high

frequency response to accommodate for placement near

plants and other landscaping features. Feel free to position the

product within your landscaping, camouaged near bushes

or shrubs. Rockustics products strive to blend into the natural

aesthetic of their surroundings.

Be sure to account for the wires which will run from the rock to

your stereo or audio source. Camouage wires by running them

an inch below ground level when possible.

Diagram A

XT-PowerRock

INSTALL INSTRUCTIONS

Ultra-Fidelity Outdoor Speakers

Contact: MSE Audio, 855.663.5600 / 913.663.5600 / sales@mseaudio.com

Cautions and Maintenance

All Rockustics Rock Series speakers are sealed and fully

weatherproof. However, DO NOT place speakers where

the grille will be in the path of a sprinkler system. Sprinklers

typically have a high water pressure level that can damage

speaker cones if hit directly.

DO NOT place soil or wood chips over the speaker grille. If the

grilles accumulate a build up of soil, the speaker may become

damaged. If build up does occur, simply rinse the grille with a

garden hose set to a low pressure level. Accumulated soil may

also promote undesired insect trafc into the speaker. Insects

may eat through the speaker cone. Chemical sprays may also

cause damage to the rubber of the speaker surround. This in-

cludes bug spray, deck sealant, some fertilizers and oil based

products. Speakers MUST be covered when applying these

treatments or chemicals in your yard.

For environments that get snow and ice during the winter

months, be sure to check that the openings and woofer cone

are clear and there is no hard-packed snow or ice built up in

these areas before playing. If there is ice or snow present on

the cone, use a hair dryer set on a low setting to to melt it away.

If the speakers are not going to be used during winter months, it

is recommended that they either be disconnected and brought

indoors, or covered with a plastic bag to help protect the

speaker components.

Step by Step Setup

1. Locating Wire

Locate speaker wire on the

underside of the speaker. Strip

wire ends if necessary.

2. Gasket

Attach the gasket to the smooth

side of the bottom cover plate.

3. Attaching Gland

Attach the supplied liquid-tight

strain relief gland to the cover

plate and thread signal wires

through the gland.

4. Conduit

Attach the conduit clamp to the

cover plate. It may be neces-

sary to increase the opening in

the cover plate to t the conduit

connector. Thread signal wires

through the conduit clamp and

afx the conduit clamp.

5. Connecting Wire

Connect the speaker wire to

the input signal wire. Red is

positive, black is negative. Use

included wire nuts to secure

the connection. Tuck wires and

wire nuts into the pocket on

the underside of the speaker.

6. Tap Settings

To change tap settings, locat-

ed the tap switch on the ud-

nerside of the rock behind the

cover plate. Use a small at

head screwdriver to adjust the

switch for the desired setting.

The tap switch is a six-position

rotary switch with positions

for 120 W, 60 W, 30 W, 15 W,

7.5 W, and transformer bypass

(8Ω). The tap switch will be set

to the highest 70.7 volt setting

from the factory (120 W).

7. Cover Plate

Place cover plate over the pocket

on the underside of the speaker

and secure with the 4 supplied

screws. This process will be the

same if you are using the conduit.

8. Done

Produkt Specifikationer

Mærke:	Rockustics
Kategori:	Ikke kategoriseret
Model:	PowerRock

Har du brug for hjælp?

Hvis du har brug for hjælp til Rockustics PowerRock stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Rockustics Manualer

Rockustics Rocquette SweetSpot Manual

30 Juli 2025

Rockustics PowerRock Manual

30 Juli 2025

Rockustics Surround Stone 5 Manual

29 Juli 2025

Rockustics OctoRock Manual

29 Juli 2025

Rockustics PavaRocci Manual

29 Juli 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Martin Audio CMX1A Manual

29 September 2025

BBB BHP-94 Manual

29 September 2025

Megasat D4 Profi-Line Manual

29 September 2025

Graco 244161 Manual

29 September 2025

BBB BHP-946 Manual

29 September 2025

Insignia NS-TS3AIEW24 Manual

29 September 2025

Wise SD-S512 Manual

29 September 2025

ZeeVee STBi3 Manual

29 September 2025

PCE Instruments PCE-HM 100 Manual

29 September 2025

PCE Instruments PCE-HM 500 Manual

29 September 2025