Russound AB-3.2 Manual

Russound Hi-Fi system AB-3.2

Læs gratis den danske manual til Russound AB-3.2 (6 sider) i kategorien Hi-Fi system. Denne vejledning er vurderet som hjælpsom af 20 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 10.5 anmeldelser. Har du et spørgsmål om Russound AB-3.2, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/6

AB-3.2

Automatic Speaker Selector

Instruction Manual

Product Overview

The Russound AB-3.2 Automatic Speaker Selector is designed to provide automatic switching of two

amplified audio sources to a single pair of speakers. The AB-3.2 will automatically switch from the

main audio system (AMP A) to a local audio source (AMP B) when the local source is active. For

example, connect the speaker output of your Russound audio system to the AMP A input, your main

left and right home theater speakers to the speaker connectors, and the home theater main left and

right speaker output to the AMP B input. If you are listening to the Russound system (AMP A) and

turn on your home theater (AMP B), the AMP B audio will override the AMP A audio and the home

theater sound will be heard over the local speakers.

The AB-3.2 includes a sensitivity trigger adjustment to adjust the volume level where switching

occurs. It also includes a delay adjustment to prevent source switching during the absence of a

signal. The AB-3.2 is powered by a 12VDC detachable power supply (included). Country-specific

12VDC detachable power supplies can be substituted for use outside the U.S.

Installation

To minimize the possibility of picking up extraneous noise, it is recommended that the AB-3.2 be

located near the AMP B source.

Connect the whole-house or distributed audio system amplifier outputs to the AMP A Input

connectors. Connect the local source amplifier output (i.e., home theater output or local

receiver/music system) to the AMP B Input connectors. Connect the local speakers to the Speaker

Output connectors. Please observe signal polarity (+/-) and left/right channel orientation on all

connections. Connect the 12VDC power supply to the power input jack and plug the supply into a

non-switched AC outlet. The Power LED should light to indicate that the AB-3.2 is getting voltage

from the power supply and is ready for use.

Sensitivity Setup

Set the trigger control approximately halfway (12 o’clock) and set the delay to minimum (fully

counterclockwise). Turn on the local source and set the volume to a normal listening level. The AB-

3.2 should switch to the AMP B Input and you will hear the local source audio through the

speakers. The green LED on the AB-3.2 should also be on to provide a visual confirmation that the

AB-3.2 has switched to the AMP B Input. The AB-3.2 may also begin to switch back to the AMP A

Input during pauses and silent periods in the programming from AMP B (this is normal and is

adjusted in the Delay Setup section). Gradually reduce the volume from the AMP B source until you

reach the minimum listening level you want for this source. If the AB-3.2 switches back to AMP A

while you are doing this (i.e., LED turns off and speakers are silent), adjust the sensitivity trigger

control until the AMP B source is selected once again. It’s best to perform this adjustment with a

program which has some continuous signal source (i.e., shopping channel on TV), as pauses in the

signal will cause the AB-3.2 to switch back to the AMP A Input. If this on/off switching is too

distracting, you can increase the delay control setting to compensate.

Delay Setup

The mid-range setting of the delay control provides a delay of approximately 10 to 15 seconds. This

should be a good setting for most installations. If you use the AB-3.2 primarily at lower volume

levels you will need to add more delay to prevent the AB-3.2 from incorrectly switching back to the

AMP A Input during quiet periods in the programming from AMP B. Adjust the Delay control

clockwise to increase the delay time and counterclockwise to reduce the delay time.

Note: If AB-3.2 relays continually click, adjust the trigger control to less than 1/4-turn or until relays

stop clicking.

Produkt Specifikationer

Mærke:	Russound
Kategori:	Hi-Fi system
Model:	AB-3.2

Har du brug for hjælp?

Hvis du har brug for hjælp til Russound AB-3.2 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Hi-Fi system Russound Manualer

Russound SDB-4.1 Manual

8 Juli 2025

Russound SDB-6.1 Manual

8 Juli 2025

Russound SDB-2.1 Manual

8 Juli 2025

Russound SMZ8 Manual

21 Februar 2025

Russound SMZ16-PRE Manual

21 Februar 2025

Russound CAA66 Manual

1 September 2024

Russound USRC Manual

1 September 2024

Russound MCA-66 Manual

1 September 2024

Russound XTS5.5 Manual

1 September 2024

Russound BTA-2 Manual

1 September 2024

Hi-Fi system Manualer

Nyeste Hi-Fi system Manualer

OSD Audio XSP2-1 Manual

13 August 2025

Audizio RP111 Manual

13 August 2025

Samsung MX-D750D Manual

10 August 2025

Samsung MM-T8 Manual

10 August 2025

Yamaha CD-C603 Manual

10 August 2025

Auna MC 120 Manual

8 August 2025

Auna Harvard IR Manual

8 August 2025

Auna Belle Epoque Manual

8 August 2025

LD Systems MAUI 5 GO 100 Manual

8 August 2025

Renegade RXA 550 Manual

8 August 2025