Russound SDB-4.1 Manual

Russound Hi-Fi system SDB-4.1

Læs gratis den danske manual til Russound SDB-4.1 (4 sider) i kategorien Hi-Fi system. Denne vejledning er vurderet som hjælpsom af 3 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 2 anmeldelser. Har du et spørgsmål om Russound SDB-4.1, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/4
SDB Series
Dual Source Speaker Selectors
Installation Manual
2 3 4 5 6
SDB-6.1
O
FF A
O
N B
O
O
NB
O
O
N B
O
FF A
O
N B
O
O
N B
O
FF A
O
N B
1
O
FF
ON
FAMI ROOM LY
GUEST THMASTER TH GUEST BEBABA DMASTER BEDTHEATER ROOM
2 3 4
SDB-4.1
O
O
NB
O
O
N B
O
FF A
O
N B
O
O
N B
1
O
FF
ON
PORCH
MASTER BED KITCHENMASTER TH BA
2
S 1 DB-2.
O
FF A
O
O
O
N B
1
O
FF
ON
MASTER TH MASTER BEBA D
2 Russound SDB Series Installation Manual
Rev. 5
Description
The SDB-2.1, SDB-4.1 and the SDB-6.1 are high-power, dual-source, autoformer-
based speaker selectors with individual volume controls for 2, 4 or 6 areas/rooms.
Dual-source operation means either one of two dierent ampliers/receivers
can be chosen to power selected speakers independently. For example, you can
choose to listen to jazz music in a couple of rooms and classical music in all the
others. Each room has its own input selector, volume control and on/o switch,
located on the front of the unit. The SDB speaker selectors work with all speakers
rated from 4 to 8 ohms, and ampliers rated for 4 to 8 ohm loads.
Setting the Impedance
The impedance of the autoformers in SDB speaker selectors is set at the factory
to be proper for most applications. The SDB-2.1 comes set at 2X; the SDB-4.1
at 4X; and the SDB-6.1 at 8X. However, if certain applications require changing
the impedance setting, simply remove the cover of the unit and re-position the
jumpers on the autoformers to the necessary impedance-matching setting.
Russound SDB Speaker Selectors autoformers can be set to impedance-matching
settings of 2X, 4X or 8X.
Determine the amplier’s minimum impedance. Consult the individual 1.
product specications or the back panel of the amplier near the speaker
terminals. AC impedance is measured in ohms.
Identify the correct impedance-matching chart below according to your 2.
amplier’s minimum impedance: either for a 4 ohm amplier or an 8 ohm
amplier. If your amplier is 6 ohm stable, use the 8 ohm chart.
Determine the impedance for each pair of speakers (see its manual). 3.
Determine the total number of 4 ohm pairs of speakers (rows on charts). 4.
Determine the total number of 8 ohm pairs of speakers (columns on 5.
charts).
Use the appropriate row and column to determine jumper settings. 6.
proDuct DeScription / connectionS
Connections
All SDB models have 4-pole screw down removable terminals for speaker and
amplier connections. These accept wire up to 12 gauge.
Remove the terminal by rmly pulling it out of its 4-pole connector. Strip about
3/8” of insulation from the ends of all wires to be connected. If necessary, twist the
exposed conductor to insure that no loose strands exist. Insert the wire ends into
the screw down connector, being careful to observe proper channel and polarity.
Tighten the screws on the connectors. Connect the amplier(s) and each speaker
pair to the appropriate connector.
Speaker connections can support multiple speaker pairs wired in parallel or series,
provided their combined impedance is a minimum of 4 ohms.
Setting System Volume
It is important to properly adjust an impedance-matching system to avoid
distortion or DC clipping (DC voltage will be produced from an amplier that is
overworked or that has an improper load). These can cause an amplier/receiver
to go into protection, and can cause autoformers on volume controls to heat
up, damaging system components. To set up the system, the amplier/receiver
volume should be at its lowest setting, and the selector volume control should be
at the highest setting. Slowly adjust the amplier/receiver volume to a level that is
acceptable for the amplier to produce without clipping.
Operation
To operate the SDB speaker selector, simply power the ampliers and select a source
for each amplier. At the speaker selector, turn on the selected pair of speakers and
select AMP A or AMP B. Set the volume by rotating the control clockwise to increase
volume or counter-clockwise to decrease volume. The SDB speaker selectors allows
operation of any combination of speakers selected to either amplier A or B.
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
0 - 1X 1X 2X 2X 4X 4X 4X 4X 8X 8X 8X 8X 8X 8X 8X 8X
1 1X 2X 2X 4X 4X 4X 4X 8X 8X 8X 8X 8X 8X 8X 8X
2 2X 4X 4X 4X 4X 8X 8X 8X 8X 8X 8X 8X 8X
3 4X 4X 4X 8X 8X 8X 8X 8X 8X 8X 8X
4 4X 8X 8X 8X 8X 8X 8X 8X 8X
5 8X 8X 8X 8X 8X 8X 8X
6 8X 8X 8X 8X 8X
7 8X 8X 8X
8 8X
Impedance Matching For 4-ohm Amplifiers
8-ohm irs Pa
4-ohm Pairs
0 1 2 3 4 5 6 7 8
0 - 1X 2X 4X 4X 8X 8X 8X 8X
1 2X 4X 4X 8X 8X 8X 8X 8X
2 4X 8X 8X 8X 8X
3 8X 8X 8X
4 8X
Impedance Matching r 8-ohm Amplifiers Fo
8-ohm irs Pa
4-ohm Pairs

Produkt Specifikationer

Mærke: Russound
Kategori: Hi-Fi system
Model: SDB-4.1

Har du brug for hjælp?

Hvis du har brug for hjælp til Russound SDB-4.1 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Hi-Fi system Russound Manualer

Russound

Russound SDB-4.1 Manual

8 Juli 2025
Russound

Russound SDB-6.1 Manual

8 Juli 2025
Russound

Russound SDB-2.1 Manual

8 Juli 2025
Russound

Russound SMZ8 Manual

21 Februar 2025
Russound

Russound SMZ16-PRE Manual

21 Februar 2025
Russound

Russound CAA66 Manual

1 September 2024
Russound

Russound USRC Manual

1 September 2024
Russound

Russound MCA-66 Manual

1 September 2024
Russound

Russound XTS5.5 Manual

1 September 2024
Russound

Russound BTA-2 Manual

1 September 2024

Hi-Fi system Manualer

Nyeste Hi-Fi system Manualer

Samson

Samson Expedition XP106wDE Manual

8 Juli 2025
Teufel

Teufel Ultima 40 Aktiv 3 Manual

8 Juli 2025
Bigben Interactive

Bigben Interactive TW7UKFLAG Manual

8 Juli 2025
Samsung

Samsung MAX-KD110 Manual

8 Juli 2025
Samsung

Samsung HW-QS760GF Manual

8 Juli 2025
Samsung

Samsung MM-B5 Manual

8 Juli 2025
Bigben Interactive

Bigben Interactive TW7NYC1 Manual

8 Juli 2025
Teradek

Teradek Bolt 3000 XT Manual

7 Juli 2025
Teradek

Teradek Bolt 4K TX Module Manual

7 Juli 2025
Teradek

Teradek Cube 775 Manual

7 Juli 2025