Samlex BS 140 DUAL Manual

Samlex Batterioplader BS 140 DUAL

Læs gratis den danske manual til Samlex BS 140 DUAL (2 sider) i kategorien Batterioplader. Denne vejledning er vurderet som hjælpsom af 97 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 49 anmeldelser. Har du et spørgsmål om Samlex BS 140 DUAL, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

www.samlex.com

www.samlex-solar.com

BS 100 DUAL

BS 140 DUAL

Model No.

BATTERY SEPARATOR

OWNER’S MANUAL / GEBRUIKSAANWIJZING

Please read this manual before operating your separator

Intelligent Battery Separator

Installation and user’s manual

Description:

The BS microprocessor controlled battery separator

is used in multi-batteries systems like on boats,

caravans and campers. It supervises the primary

battery state of charge and therefore avoids starting

problems. The BS can also be used as a voltage

dependent switch.

The working principle is the following: the BS lets the

primary battery being recharged by the alternator until

a voltage of 13.2V (26.4V) during at least 7 seconds is

reached. Then the two batteries are put in parallel by

the contact of the relay. The secondary users are

normally connected to the auxiliary battery. The relay

opens when the batteries voltage reaches 12.8V

(25.6V) during at least 60 seconds. This way the

starter battery remains charged.

If a battery charger is connected to the auxiliary battery

and this battery reaches a voltage of 13.2V (26.4V)

during at least 7 seconds, the relay closes and

charges at the same time the starter battery. This is an

advantage if the vehicle remains stationary over a long

period of time.

If the battery charger is disconnected and the battery

voltage reaches 12.8V (25.6V) during at least 60

seconds, then the BS separates again the two

batteries.

Start assistance:

The BS has an additional connection enabling an assis-

tance to the starting. If the connection 85 (BS 100) or

86 (BS 140) is connected to the starter contact, the BS

contact closes and this way the 2 batteries contribute to

the engine start.

Cautious when this function is used very high currents

may go through the relay contact by the start of big

engines. These high currents may damage the contact

of the BS if they exceed its nominal current.

Voltage dependent switch:

In some cases it is needed to have a powerful DC

source supply but only when the engine is running.

The BS allows also this kind of installations. It is

sufficient to simply connect the primary battery to the

connection 30, the system earth to the connection 86

(BS 100) or 85 (BS 140) and the positive of the equipment

to supply to the connection 87. When the engine runs a

voltage of 13,2V (26,4V) during at least 7 seconds is reached,

the equipment is then powered thru the contact of the BS.

Protection against overvoltages:

The BS has also a function enabling to protect the

battery and the appliances that are connected to it

against an overvoltage generated, for instance, by a

defectuous alternator. As soon as a voltage higher

than 16 V (32V) is detected, the contact of the BS

opens immediately.

Installation:

To implement the function « start assistance », a fuse

protected connection has to be carried out between

the connection 85 (BS 100) or 86 (BS 140) and the contact

o f t h e s t a r t e r c o n t a c t .

A short-circuit between the positive and negative

of the batteries can damage your system. Make

sure that the connections are properly done!

Technical specifications:

Supply: Automatic detection 12/24 V

Max. current: 100 A (BS 100) or 140 A (BS 140)

Battery connection: M6

Other connections: Faston 6,3 mm

Cable cross section: 25mm2

Consumption OFF: 12V=1.5mA / 24V=1.5mA

Consumption ON: 13.5V=360mA / 27V=160mA

Minimum chargetime: 60 seconds

Fast opening: < 11.8V (12V) / 23.6 (24V)

after 4 seconds

Connections:

30 Positive terminal of the primary battery (starter

battery)

85 Ignition switch (only if « start assistance » is

needed)

86 Negative terminal (Cautious this connection

must always remain connected via a fuse of 3A)

87 Positive terminal of the auxiliary battery (If the

function « voltage dependent switch » is

needed, connect the equipment positive here)

86 for BS 140

85 for BS 140

+12Vdc(+24Vdc)

External

Charger

Alternator

Primary

Battery

Auxiliary

Battery

To the starter contact

(optional, see installation)

86 or 85

Caution!

The fuses must be

dimensioned accordingly

to the cables cross-

sections!

+12Vdc(+24Vdc)

External

Charger

Alternator

Primary

Battery

Auxiliary

Battery

To the starter contact

(optional, see installation)

86 or 85

Caution!

The fuses must be

dimensioned accordingly

to the cables cross-

sections!

via een zekering van 3A

86 voor BS 140

85 voor BS 140

Produkt Specifikationer

Mærke:	Samlex
Kategori:	Batterioplader
Model:	BS 140 DUAL

Har du brug for hjælp?

Hvis du har brug for hjælp til Samlex BS 140 DUAL stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Batterioplader Samlex Manualer

Samlex EVO-1224F Manual

22 August 2024

Samlex SEC-1250UL Manual

22 August 2024

Samlex ACR-160 Manual

22 August 2024

Samlex SEC-2425UL Manual

22 August 2024

Samlex SEC-1215UL Manual

22 August 2024

Samlex SEC-1230UL Manual

22 August 2024

Samlex BS 140 DUAL Manual

6 August 2024

Samlex BS 100 DUAL Manual

1 August 2024

Samlex EVO-1212F Manual

19 Juli 2024

Batterioplader Manualer

Nyeste Batterioplader Manualer

Joy-It SBC-Buck04-5V Manual

8 Oktober 2025

Ansmann APM1 Manual

8 Oktober 2025

Ansmann USB-C Wall Charger 130PD Manual

8 Oktober 2025

Kress KAC877E Manual

5 Oktober 2025

Socket Mobile DuraCase Manual

3 Oktober 2025

Gardol 20V/30 Manual

3 Oktober 2025

Toolcraft ALG-1000 Manual

2 Oktober 2025

Nitecore NB Plus Manual

2 Oktober 2025

Draper D20 55913 Manual

1 Oktober 2025

Draper 53489 Manual

1 Oktober 2025