Sanwa KDP10 Manual

Sanwa Måleudstyr KDP10

Læs gratis den danske manual til Sanwa KDP10 (3 sider) i kategorien Måleudstyr. Denne vejledning er vurderet som hjælpsom af 24 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 12.5 anmeldelser. Har du et spørgsmål om Sanwa KDP10, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

KDP10

VOLTAGE DETECTOR SUPPORTER

INSTRUCTION MANUAL

— 3 —

CAUTION

Do not use the product near a high-eld area including a transformer

or high-current circuit, an electromagnetic-wave-emitting area

including a wireless device or radio, or an electrostatic-charged area.

Otherwise, an unwanted behavior may be detected on a detection

principle.

NOTICE

• Do not give an impact on the product, including a strong vibration or

fall. It may damage the product.

[2] APPLICATIONS AND FEATURES

2-1 Applications

This product, when attached to the handle of the manual

cable cutter, reacts and warns the user with light and sound

about an erroneous cut when the sheathed cable of the

commercial power (frequency: 50 Hz/60 Hz) is a live wire.

2-2 Features

•Attachable to your manual cable cutter

•Warns the live-wire status of a cable with a buzz and LED

•Detectable with gloves on

•Approx. 5 months of battery life in standby mode

•With a sensitivity control volume

2-3 Detection Mechanism

A detection takes place when a signal run triggered by a

difference of potential between the electric ﬁeld of the live-wire

cable and a human body runs through the product.

Cable Tool

Outlet

Product Human

body

Ground

Cutting tool and the product

本社= 千代田田2東京都区外神 -4-4 ビル･電波

郵便番号 10= 1-0021･電 =東話京（03）3253-48 ㈹71

大阪所=大阪市浪速区恵美須西2営業 -7-2

郵便番号 55= 6-0003･電 =大話阪（06）6631-73 ㈹61

Dempa Bldg., 4-4 S okanda 2-Chome, Ch -Ku,Tokyo, Japanot iyoda

— 4 —

[3] BEFORE USE

3-1 Checking the Package

KDP10 main unit

Rubber ring M × 2

Rubber ring S × 2

Sensitivity control volume

cover

(with the main body x

1, spare ×2)

LR44 (coin battery) ×2

Battery holder

KDP10

VOLT AGE DET ECT OR SUPPO RTER

INST RU CT ION MANUAL

Instruction Manual

(This document)

3-2 Names of Component Units

Sensitivity control

volume

LED

Battery holder

Power indicator

Power slide

switch

Rubber ring

attachment position

Sensitivity control

volume cover

Power slide switch

— 1 —

[1] SAFETY PRECAUTIONS - Read Before Use -

Thank you for purchasing KDP10, a Voltage Detector

Supporter for a manual cable cutter. This Voltage Detector

Supporter is intended to eliminate accidents caused by an

erroneous cut of a live-wire cable for a commercial power’s

alternate voltage (frequency: 50 Hz/60 Hz) by being attached

to a manual cable cutter.

Read these instructions fully before using the product for

your proper and safety use. In addition, keep this document

handy with the product at all times so that you can consult it

as needed.

Use of the product, which is not designated in this document,

may endanger the safety of the user, damage the equipment,

or impair a protection function of the product.

1-1 Explanation of Warning Symbols

The following symbols are used in this product labels and

document to explain safety instructions:

DANGER

Causes a death or severe damage unless avoided.

WARNING

May cause a death or severe damage unless avoided.

CAUTION

May cause a mild or moderate damage unless avoided.

NOTICE

May cause physical damages to the product or other objects

unless avoided.

May cause an electric shock or a re by an electrical hazard.

Indicates To-Do items (compulsory instructions).

Indicates Not To-Do items (prohibitions).

— 5 —

LED Lits/ﬂashes when the power is ON, the battery life is

low, or the tool approached to the live-wire cable.

Rubber ring

attachment

A position at which the included rubber rings are

mounted when attaching the product to a tool.

Sensitivity control

volume cover

Remove this when adjusting the sensitivity volume.

Sensitivity control

volume

Adjusts and controls the sensitivity volume. Rotating

the knob to “−” decreases the sensitivity while rotating

it to “+” increases the sensitivity.

Battery holder Open this when replacing the batteries.

Power slide Slide to turn the power ON/OFF.

Power indicator Indicates the status of the power supply (ON: red,

OFF: black).

3-3 Installing Batteries

Be sure to install batteries before use after you purchase the

product.

“5-2 Replacing the Batteries”

When the battery is exhausted

If the power is turned ON with the low voltage of internal

batteries, you are warned with a buzz and LED as shown

below. Replace both of the batteries.

A buzz and LED illumination (for approx. 4 seconds)  LED

slowly ﬂashing

* The battery status cannot be detected when the power remains ON.

Do not forget to cycle the power of the product before use and make

sure that the buzzer and LED does not show the status as above.

— 2 —

1-2 Warning Instructions for Safe Use

Users are obliged to follow the instructions below when using

the product.

DANGER

Follow the instructions below. May cause a re or an electric shock.

• This product or a manual tool with the product attached is not

a voltage detector. Do not use the product as an alternative to a

voltage detector.

• Do not contact a metallic part of the cable cutter with an

uninsulated live part.

Follow the instructions below. May cause an electric shock.

• Do not touch the product with wet hands.

• Do not touch a superimposed voltage part during a peripheral.

• Ensure that you wear a “protective equipment” before use.

• Do not give a strong impact on the product. If the product had a

strong impact, make sure to check its operation before use. If you

cannot ensure the normal behavior, refrain from using the product.

Do not store the product under a direct sunlight, high temperature,

low temperature, humid, or dew-condensed environment. Make sure

to check the operation before using the product which had been kept

in such an environment. If you cannot ensure the normal behavior,

refrain from using the product.

WARNING

Follow the instructions below. May cause an electric shock.

• Do not use the product in a way other than the one designated in

this document.

• Refrain from using the main unit, rubber rings, or the cutter which

are damaged or broken.

• Do not use the product with the case or a battery holder removed.

• Do not repair or retrot the product, except for a battery

replacement.

Follow the instructions below. Otherwise, the product will not work

normally, causing potential and unexpected accidents.

• Use the product indoors.

• Do not use the product on a circuit beyond 600V.

• Make sure to check the product before use.

Do not leave removed button batteries unattended. Otherwise, an

accidental ingestion by an infant may arise.

— 6 —

[4] HOW TO USE

DANGER

This product and a manual cutter with the product attached is not

a voltage detector. Use a voltage detector or multimeter for voltage

detection. May cause a re or an electric shock.

Ensure that you wear a “protective equipment” before use. May

cause an electric shock.

NOTICE

• This product is intended for a general 7”/8” manual cable cutter. The

product may not be available for some cutters.

Situations where correct detection is not possible

•A live-wire may not be detected if the size of sensitivity

volume is too low.

“4-5 Adjusting the Sensitivity Volume”

•The product is exclusively for a commercial power’s

alternate voltage (frequency: 50 Hz/60 Hz), A circuit

with a different frequency, for example, secondary

voltage of an inverter, cannot be detected.

•A live-wire may not be detected depending the

surrounding environment, and how the product is

attached or gripped.

•When a human body is touching the metallic tip of the

cutter or the sheath of the cutter’s handle is thin, in

principle, it is difﬁcult for a signal to run through the

product, which potentially disables the detection of a

live-wire.

•A detection sensitivity decreases when a target live-

wire cable is touching a human body.

•A live-wire cannot be detected on a shielded cable

because the product cannot detect an electric ﬁeld.

•An electric ﬁeld of an adjacent live-wire cable may be

detected.

02 -1709 2040 2040C

Vegetable-oil-based ink is used for this document.

— 7 —

Follow the procedure below to use the product.

4-1 Check the Main Body

•Visual appearance check: Does the main body have ﬂaws

on its appearance due to a fall or others?

•Battery life check: Is a buzz heard for approx. 4 seconds,

and the LED ﬂashes slowly after illuminated?

“4-3 Checking ON/OFF of the Power”

•Are the main body, rubber ring, or hands wet with water?

4-2 Attaching to the Cutting Tool

1) Place the product inside the cable cutter’s handle so that

a working hand touches an electrode part.

2) Secure the product tightly with a provided rubber ring in

a correct orientation as shown in the ﬁgure below (LED

facing toward the wrist).

* Two different sizes of rubber rings (S/M) are provided. Select a ring

which suits the thickness of the cutter’s handle.

* If the product is not secured tight and apparently moving apart or

coming off from the handle, the sensitivity becomes unstable.

(1)

Rubber ring

(2)

Main body

Pull with a nger

(3)

LED

— 11 —

WARNING

Make sure that the power is turned OFF before replacing the battery.

“4-3 Checking ON/OFF of the Power”

1) Push the knob on both sides of the battery holder to pull

out the battery holder, then remove two coin batteries.

* Pull out the battery holder with the product upside down.

Otherwise, the batteries will fall.

Battery

holder

Knob

2) Get two new batteries ready, check the polarity and

mount them into the battery holder.

* Recommended battery: LR44 (alkali-coin battery) 1.5 V × 2

3) Insert back the battery holder until you hear a click sound.

— 8 —

4-3 Checking ON/OFF of the Power

Turn ON-OFF the power to check if the buzzer and LED are

working correctly.

* Refrain from using the product when a failure has been found.

1) Turn the power ON

Press the power slide switch (ON) and identify that the

power indicator is red.

A buzz is heard nine times and the LED starts ﬂashing.

* When the power is turned ON, and a buzz is heard for approx. 4

seconds and the LED ﬂashes slowly, it indicates that the batteries

needs to be replaced.

“5-2 Replacing the Batteries”

2) Turn the power OFF

Press the power slide switch (OFF) and identify that the

power indicator is black.

LED

Power

indicator

Power OFF

Black

Power ON

Red

Power slide

switch

Power slide

switch

— 12 —

[6] TROUBLESHOOTING

Status What to check

The power does

not turn ON

Is the polarity of a battery correct?

“5-2 Replacing the Batteries”

Is the battery life low?

“When the battery is exhausted” in “[3] Before

Use”

Unable to detect

live-wires

Is the product used under conditions where detection

is not possible?

“[4] How to Use” in “Situations where correct

detection is not possible”

Is the product turned ON?

“4-3 Checking ON/OFF of the Power”

— 9 —

4-4 Checking for a normal detection

Check that the product works normally with the tip of the

manual cutter 1 to 2 cm away from the known live-wire cable

after the product is powered ON.

* Grip the cutter so that your hand touches the electrode part inside

the product.

* If the product does not work properly, do not use the product at that

place as the cutter or surrounding environment may have impacted

the product.

Electrode

Known live-wire cable

Sensitivity

control

volume

4-5 Adjusting the Sensitivity Volume

If the detection sensitivity needs to be adjusted, remove

the sensitivity control volume cover, and rotate the knob

with a Phillips-head screw driver. As the factory default, the

sensitivity is set to the maximum.

After the adjustment, place the cover back into position.

* Rotating to the left (“−”) decreases the sensitivity (insensitive), and

rotating to the right (“+”) increases the sensitivity (sensitive).

Knob

Low High

— 13 —

[7] AFTER-SALE SERVICE

7-1 Warranty and provision

Sanwa offers comprehensive warranty services to its end-

users and to its product resellers.

Under Sanwa’s general warranty policy, each instrument is

warranted to be free from defects in workmanship or material

under normal use for one (1) year from the date of purchase.

This warranty policy is valid within the country of purchase

only, and applied only to the product purchased from Sanwa

authorized agent or distributor.

Sanwa reserves the right to inspect all warranty claims to

determine the extent to which the warranty policy shall apply.

This warranty shall not apply to disposables batteries or

any product or parts witch have been subject to one of the

following causes:

1. A failure due to improper handling or use that deviates

from the instruction manual.

2. A failure due to inadequate repair or modiﬁcation by

people other than Sanwa service personnel.

3. A failure due to causes not attributable to this product

such as ﬁre, ﬂood and other natural disaster.

4. Non-operation due to a discharged battery.

5. A failure or damage due to transportation, relocation or

dropping after the purchase.

7-2 SANWA web site

http://www.sanwa-meter.co.jp

E-mail: exp_sales@sanwa-meter.co.jp

— 10 —

4-6 Using the Tool for Work

Approach the cable cutter with the product attached to the

live-wire cable.

* If you hear a buzz and the LED flashes, stop cutting the cable. Use a

voltage detector or multimeter to check if it is a live-wire or not, then

resume the work.

* Turn OFF the product after use.

[5] MAINTENANCE

5-1 Instructions on Cleaning and Storage

NOTICE

• Do not use a thinner or alcohol to wipe and clean the product as it is

weak against a volatile solvent. Wet a lint-free soft cloth with water and

wipe the dirt off.

• As the product is weak against heat, do not place it close to an object

which generates heat.

• Do not store the product in a place where it is prone to shake or may

fall.

• Do not store the product under a direct sunlight, high temperature, low

temperature, humid, or dew-condensed environment.

• Be sure to remove the batteries if the product will not be used for a

long time.

• Comply with local regulations when disposing or treating the product

and coin batteries.

5-2 Replacing the Batteries

If the power is turned ON with the low voltage of internal

batteries, you are warned with a buzz and LED as shown

below. Replace both of the batteries.

A buzz and LED illumination (for approx. 4 seconds)  LED

slowly ﬂashing

— 14 —

[8] SPECIFICATIONS

Item Range

Detectable voltage level

(representative value)

Approx. AC 60 V to 600 V exclusively for 50

Hz/60 Hz

(when attached to a 7”/8” cutter’s handle)

Target cable Sheathed cable (unshielded cable)

Operation check Intermittent buzz/LED illumination

Operation indicator Intermittent buzz/LED illumination

Power supply LR44 (alkali-coin battery) 1.5 V × 2

Battery life Approx. 5 months (in standby mode)

Operating temperature/

humidity

0 °C to 40 °C, 80 % RH or less with no

condensation

Storage temperature/

humidity

-10 °C to 50 °C, 70 % RH or less with no

condensation

(Be sure to store the product with the batteries

removed when not in use for a long time.)

Dimensions/weight 23 (H) × 77 (W) × 13 (D) mm, Approx. 13 g

(without batteries)

Accessories Rubber ring M x 2, S x2, sensitivity control

volume cover × 2 (spares), LR44 (coin

batteries) x 2, Instruction Manual

Sold separately KDP 10 repair set (rubber ring M x 2, S x2,

sensitivity control volume cover x 2, battery

holder)

Note that the specications or appearance of the product described in this

document may change without prior notice due to revision, etc.

Produkt Specifikationer

Mærke:	Sanwa
Kategori:	Måleudstyr
Model:	KDP10

Har du brug for hjælp?

Hvis du har brug for hjælp til Sanwa KDP10 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Måleudstyr Sanwa Manualer

29 August 2024

29 August 2024

29 August 2024

28 August 2024

28 August 2024

28 August 2024

28 August 2024

28 August 2024

28 August 2024

28 August 2024

Måleudstyr Manualer

Nyeste Måleudstyr Manualer

3 April 2025

3 April 2025

3 April 2025

3 April 2025

3 April 2025

3 April 2025

3 April 2025

3 April 2025

3 April 2025

3 April 2025