Saris Cycle-On Pro Manual

Saris Cykelholder Cycle-On Pro

Læs gratis den danske manual til Saris Cycle-On Pro (4 sider) i kategorien Cykelholder. Denne vejledning er vurderet som hjælpsom af 24 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 12.5 anmeldelser. Har du et spørgsmål om Saris Cycle-On Pro, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/4
20" wheel
tray mount
Standard wheel
tray mount
USER MANUAL
C
C
C
C
Cy
y
y
y
yc
c
c
c
cl
l
l
l
le
e
e
e
e-
-
-
-
-O
O
O
O
On
n
n
n
n
P
P
P
P
Pr
r
r
r
ro
o
o
o
o
Please READ and FOLLOW all instructions carefully.
4017 (1 1/4” RECEIVER) OR 4018 (2” RECEIVER)
ASSEMBLE FRONT WHEEL TRAYS - Determine which holes you
will use to mount the front wheel trays (Fig. 1A). For 20” tires inner-
#4012 add on kit).
Tube
Bolt
Front Wheel
Tray
Washer
Nut
Insert bolt through tube, slide wheel tray on, fasten with washer
and nut (Fig. 1B). Tighten nut until it is snug, where wheel tray
pivots freely. Repeat for each of the 2 front wheel trays.
Next attach the rack to the tilt bracket. Assemble in stepped
order (step 1, 2, 3) as shown above. Tighten knob at end of
bracket until bracket is tight in receiver.
1
2
3
Insert plugs into
unused holes.
1A
1B
2B
MUST use 2 wheel trays per wheel.
See Picture 4B.
Front Wheel
Tray
Washer
Nut
Bolt
Tube
Insert hitch pin and lock into place as shown above. (Note:
Do not stick locking cable through hole, only hitch pin.)
Steel Pin
Pin with
Lanyard
Knob
1
2
12-15”
3
4
5
Depress the rear wheel clamp lever, and rotate to open position.
Upright Arm
Press
Rotate
Open
Position
Push button on upright arm and rotate arm away from
center of rack.
Set bike into trays. Front wheel should be set into the front wheel
trays. Extend and rotate upright arm to vertical position. Push down
on upright arm to contact top of wheel's front tire. Once contact is
achieved, press down on upright arm for additional "clicks", until
wheel is held securely.
Rotate wheel so the largest gap is centered under wheel hub.
Align rear wheel clamp with largest gap in spokes of rear wheel.
Rotate clamp between spokes closing onto rear wheel tray.
Front Wheel Trays
Upright Arm
Upright Arm
(vertical position)
Push
***Note: For bicycles with odd rims or 40 spoke or greater
wheels, additional straps (available through Saris) should
be used in replace of the rear wheel clamp. Thread strap
into rear wheel tray slots and secure bicycle.
***Note: Bicycles with 20” wheels should be loaded
closest to vehicle.
Press
Rotate
Closed
Position
Removal of Bicycles: Reverse instructions 3-5 to
remove bicycle from rack.
Check clearance. It is the responsi-
bility of the user to ensure the nec-
essary clearance (dependent on
vehicle, load, driving territory, etc.) is
given from load to ground.
Generally, 12-15” is adequate. Load
smallest bicycle closest to the
vehicle. Lock bikes to rack with
locking cable provided. Lock must
pass through bikes and rack for total
security.
Slide arm
into base
Always stow arms in this position.
Push
Rotate
4B
4A
3
5A
5B

Produkt Specifikationer

Mærke: Saris
Kategori: Cykelholder
Model: Cycle-On Pro

Har du brug for hjælp?

Hvis du har brug for hjælp til Saris Cycle-On Pro stil et spørgsmål nedenfor, og andre brugere vil svare dig


Cykelholder Saris Manualer

Saris

Saris SUPERBones Manual

10 August 2024
Saris

Saris Cycle-On Pro Manual

4 August 2024
Saris

Saris Bones RS Manual

3 August 2024
Saris

Saris Bones 3 Bicycle Carrier Manual

3 August 2024
Saris

Saris Bones 3 Manual

3 August 2024
Saris

Saris Bones 2 Manual

3 August 2024
Saris

Saris Sentinel - 2 Bike Manual

1 August 2024

Cykelholder Manualer

Nyeste Cykelholder Manualer

Thule

Thule Bike Stacker BSTK2 Manual

12 Januar 2025
Eufab

Eufab Crow Manual

1 Januar 2025
Cybex

Cybex Zeno Bike Manual

29 December 2024
Buzz Rack

Buzz Rack Buzzracer H2 Manual

8 December 2024
Cruz

Cruz Stema 2 Manual

20 November 2024
Twinny Load

Twinny Load E-Active Manual

4 Oktober 2024
Yakima

Yakima HoldUp +2 Manual

3 Oktober 2024
Eufab

Eufab 16411 Manual

25 September 2024
Enduro

Enduro BC260BE Manual

23 September 2024
Spinder

Spinder Falcon 3F Manual

22 September 2024