Satco 60-6432 Manual

Satco Lys 60-6432

Læs gratis den danske manual til Satco 60-6432 (2 sider) i kategorien Lys. Denne vejledning er vurderet som hjælpsom af 15 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 8 anmeldelser. Har du et spørgsmål om Satco 60-6432, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

INSTALLATION AND SAFETY INSTRUCTIONS

FOR YOUR SAFETY

WARNING: BE SURE THE ELECTRICITY TO THE WIRES YOU ARE WORKING

ON IS SHUT OFF; EITHER THE FUSE IS REMOVED OR THE CIRCUIT BREAKER

IS SHUT OFF.

GENERAL

You don’t need special tools to install this xture. Be sure to follow the steps

in the order given. Under no circumstances should a xture be hung on house

electrical wires, nor should a swag type xture be installed on a ceiling which

contains a radiant type heating system. Read instructions carefully. If you are

unclear as to how to proceed, consult a qualied electrician.

NOTE: Proper wiring is essential for the safe operation of this xture.

FIXTURE ASSEMBLY

Carefully remove the xture from the carton and check that all parts are included

as shown in gure. Be careful not to misplace any of the screws or parts, which

are needed to install this xture.

STEP 1: Thread tube. Carefully pass the wires through each tube during

assembly. Repeat this step until the desired hanging height is reached.

STEP 2: Thread the tube into canopy and body.

INSTALLATION

IMPORTANT: Do not attach xture directly to outlet box.

STEP 1: Thread mounting screw into the matching hole of cross bar.

STEP 2: Secure the cross bar to outlet box with outlet box screws.

GROUNDING INSTRUCTIONS

STEP 1: Insert the green grounding screw into the hole with two raised dimples

on the mounting cross bar. Wrap the ground wire from the xture (if supplied)

around the green grounding screw, then connect it to ground wire from the outlet

box (if not xed on the outlet box) using a wire connector (not supplied). If ground

wire from the xture is not supplied, wrap the ground wire (if not xed on the

outlet box) from the outlet box around the green grounding screw and tighten it.

NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER

SUPPLY WIRES.

STEP 2: Take note of the color of the wire(s) on your xture. Identify which

group your xture wire(s) falls into and connect the wires according to the

directions below:

GROUP A:

Connect to Black House Wire

GROUP B:

Connect to White House Wire

BLACK WHITE

* PARALLEL WIRE (round & smooth) * PARALLEL WIRE (square & ridged)

WHITE OR GREY WITH TRACER WHITE OR GREY WITHOUT TRACER

BROWN, GOLD OR BLACK

WITHOUT TRACER

BROWN, GOLD OR BLACK

WITH TRACER

NOTE: When parallel wire (SPT-I & SPT-2) is used, the tracer wire is square

shaped or ridged and the less tracer wire is round in shape or smooth (seen

best when viewed from wire end.)

STEP 3: Take your xture wire(s) from group A and place evenly against the

black wire from the outlet box. Do NOT twist wires together before using wire

connectors.

STEP 4: Fit a wire connector over the wires and screw the connector clockwise

until you feel rmness.

STEP 5: Try gently to pull the connector off the wires. If you can pull the

connector off, carefully re-do steps 3 and 4 as above, and check again for a

rm connection.

STEP 6: Connect the xture wire from group B to the white wire from the outlet

box in the same manner. Make sure no bare wires can be seen outside wire

connectors.

ITEM NO: 60-6432

ARTÍCULO Nº: 60-6432

ARTICLE N°: 60-6432

FINAL ASSEMBLY

STEP 1: After wires are connected, tuck them carefully inside outlet box. Raise

canopy allowing the mounting screw to protrude through the hole in the canopy,

and secure with ball nuts.

STEP 2: Unscrew the socket ring and snuffer from socket. Place glass over socket,

reattach the socket ring and snuffer to socket to secure glass. Install lamp (not

included). Please do not exceed the maximum capacity recommended on the

socket.

CLEANING

To clean, wipe xture with a soft cloth. Clean glass with a mild soap. Do not use

abrasive materials such as scouring pads or powders, steel wool or abrasive paper.

ORDERING PARTS

Keep this sheet for future reference, and in case you need to order replacement

parts. All parts for this xture can be ordered from place of purchase. Be sure to

use exact wording from illustration when ordering parts.

FIGURE

Line art shown may not exactly match the xture enclosed. However, the installations

do apply to this xture.

La ilustración puede no concordar exactamente con la pieza enviada. Sin embargo,

las instalaciones sí aplican para esta pieza.

Les images peuvent ne pas correspondre exactement au luminaire de la boîte.

Par contre, les directives d’installation s’appliquent au luminaire.

Produkt Specifikationer

Mærke:	Satco
Kategori:	Lys
Model:	60-6432

Har du brug for hjælp?

Hvis du har brug for hjælp til Satco 60-6432 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Lys Satco Manualer

15 Juni 2025

14 Juni 2025

14 Juni 2025

14 Juni 2025

14 Juni 2025

14 Juni 2025

14 Juni 2025

Lys Manualer

Nyeste Lys Manualer

Rockville Leaf Spinner Manual

5 November 2025

VELVET Light 2 Manual

5 November 2025

Elation DMX Operator Manual

5 November 2025

GVM -CL100B Manual

5 November 2025

GVM -B100C Manual

5 November 2025

American DJ Encore Profile PRO Color Manual

5 November 2025

Geekoto LR-18 Soft Manual

4 November 2025

VELVET Power 2 Studio Manual

4 November 2025

American DJ Encore Profile Mini Color Manual

4 November 2025

Ledgo LE-60K Manual

4 November 2025