Sauermann Si-RVP3 Manual


Læs gratis den danske manual til Sauermann Si-RVP3 (11 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 2 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 1.5 anmeldelser. Har du et spørgsmål om Sauermann Si-RVP3, eller vil du spørge andre brugere om produktet?

Side 1/11
TWO-STAGE VACUUM PUMPS
User manual
Si-RVP1, Si-RVP2, Si-RVP3
sauermanngroup.com
EN FR ES IT DE ZHPT NL
English
User manual
WARNING
For your safety and in order to avoid any damage of the device, please follow the procedure
described in this user manual and read carefully the notes preceded by the following symbol:
DO NOT ATTEMPT TO OPERATE WITHOUT USING OIL!
Use oil specically rened for Deep Vacuum Pumps. Use of oil not rened for Deep
Vacuum Pumps and/or operating with contaminated oil will void warranty.
1 Oil ll
This vacuum pump has been tested at the factory and shipped with only trace amounts of oil.
OIL MUST BE ADDED BEFORE OPERATING! Failure to add oil will damage cartridge and void warranty!
1. Make sure the oil drain valve located below the front casing is closed before attempting to add oil.
2. Remove the exhaust mufer from the top of pump and insert the oil bottle into the exhaust port.
3. Slowly add oil until oil level rises to the top of the Oil Level Line. Do not overll with oil!
4. Replace exhaust mufer.
CAUTION:
To reduce the danger of electric shock, keep the pump indoors and do not expose to rain.
DANGER:
1. Receptacle shall be well grounded, or else electric shock may be caused. Should power cord or plug
require repair or replacement, do not use the pump. If you cannot fully understand grounding instructions
and have doubt whether correct grounding is made, check with a professional electrician or service man. Do
not change the structure of attached adapter connector.
2. When pulling out power plug, make sure to pull the plug rather than the wire.
3. Do not place anything on the power cord. It may damage the wire.
4. Do not use broken plug or socket.
5. Do not pull out power plug with wet hand.
6. Do not pull out, insert power plug or turn on power switch where ammable gases may be present.
1. Wear safety glasses
2. Do not evacuate combustible, explosive or poisonous gases.
3. Do not evacuate gases that corrode metal or react chemically with pump oil.
4. The temperature of evacuated gas shall not exceed 80 °C (176 °F) and ambient temperature shall be
5 - 60 °C (41 - 140 °F) in order to perform at maximum capacity.
5. Do not operate without oil.
6. Pump and motor can be extremely hot to the touch in high ambient temperature conditions.
7. Do not block vacuum pump exhaust.
2 Checking oil level
1. Open the gas ballast valve (small brass tting located next to the handle) one turn.
2. Start pump and run with intake port capped for about two minutes. Observe the oil level with the
pump running. The oil level in the sight glass should be even with the level line.
3. If the level is low, open the intake port and run pump for 15 seconds, stop pump and observe oil level
again. Add a small amount of oil as needed.
Designation Si-RVP1-220V Si-RVP3-220V Si-RVP1-110V Si-RVP2-110V
Oil capacity 250 ml / 8.5 oz. 440 ml / 15 oz. 250 ml / 8.5 oz. 440 ml / 15 oz.
Oil capacity


Produkt Specifikationer

Mærke: Sauermann
Kategori: Ikke kategoriseret
Model: Si-RVP3

Har du brug for hjælp?

Hvis du har brug for hjælp til Sauermann Si-RVP3 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Sauermann Manualer

Sauermann

Sauermann Si-RS1 Manual

26 August 2025
Sauermann

Sauermann KNT 320 Manual

26 August 2025
Sauermann

Sauermann Si-RVP3 Manual

26 August 2025
Sauermann

Sauermann Si-RM450 Manual

26 August 2025
Sauermann

Sauermann CP 115 Manual

20 August 2025
Sauermann

Sauermann COST-S Manual

19 August 2025
Sauermann

Sauermann TH 210-R Manual

19 August 2025
Sauermann

Sauermann HST Manual

19 August 2025
Sauermann

Sauermann CP 110 Manual

19 August 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer