Scandomestic SD 46 Manual

Scandomestic Køling frysning SD 46

Læs gratis den danske manual til Scandomestic SD 46 (4 sider) i kategorien Køling frysning. Denne vejledning er vurderet som hjælpsom af 12 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 6.5 anmeldelser. Har du et spørgsmål om Scandomestic SD 46, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

SD 46

SD 76

SD 92

User manual

Scandomestic A/S · Thrigesvej 2 · DK-8600 Silkeborg

T + 45 7242 5571 · F + 45 8622 5571 · scandomestic.dk

TRANSPORTATION AND INSTALLATION

1 Place on level oor and remove the bottom packing, in order

to decrease the shock and noise.

The angle between the compartment body and ground

should be no more than 45°

2 Enough space should be left between the freeze and the

wall for ventilation.

3 Place the freezer away from heat source and do not expose

to direct sunshine.

4 Do not install where there is moisture or where it can easily

be splashed by water.

5 Do not place the freezer in environment prone to freezing.

6 The appliance should not be used in open air and should not

be exposed to rain.

ADJUSTMENT AND RUNNING

1 Adjustment of temperature: The storing temperature can be

adjusted by the thermostat of the compartment. The ther-

mostat should be adjusted according to different environ-

ment temperature and the food by rotating the knob of the

thermostat. The knob rotates clockwise from ”1” to “7”(or

direction arc)and the inside temperature turns down in

summer (anti-clockwise rotation)and up in winter(clockwise

rotation). It is usually xed to a certain point before leaving

the factory. Do not adjust too often or touch the other parts.

2 Trial running: plug in and wait. The marked drop in tempe-

rature within half an hour indicates that the freezer works

properly.

The compressor should be left to run for a period of time(6

hours in summer 4 hours in winter )before putting the food

in.

SAFETY PRECAUTIONS

1 The freezer should use a single 3-pin socket with (13A)fuse.

A multi –plug outlet should not be used.

2 You should install a suitable automatic voltage regulator not

less than 500w when the voltage is outside the range from

187V to 242V.

3 The sockets of the freezer should be connected to stable

xed connection. Under no circumstance should the wiring

be connected to such facilities as water pipe, gas pipe and

so on.

4 Once power is cut off, wait for at least 5 minutes before

plugging in again to avoid damaging the compressor or the

system.

5 Do not put combustible ,explosive or volatile dangerous

articles, heavily corrosive acid or alkali of liquid in glassware

into the freezer.

6 Children should be kept away from the freezer to avoid da-

mage to the inner container or any accidents being incurred

7 If the power cable damages, for avoid dangerous, must by

manufactory or its maintain a set or similar profession job

the personnel replaces.

FREEZING METHODS

1 Do not put too much food into the freezer or exceed the

loading line.

2 proper space should be allowed between foods to ensure

cooling air circulation.

3 Never use corrosive detergent, hot water, or washing power

to clean the freezer.

4 Do not use water to scour the freezer. Do not use hard bru-

shes or wire brushes to clean the freezer.

5 Do not use metal or sharp tools for defrosting.

6 Do not use electric heaters to heat up and defrost.

7 The green lamp is a power indicating lamp. When the power

is on, the lamp will be on.

TROUBLE SHOOTING:

The design and production comply with the relative security

standard of China. If you nd it does not work as usual, please

examine and handle it according to the following table rst. If

the situation does not improve, you must contact our after-sale

service center or our special repair division to examine and repair

the appliance.

The following problems are not causes of breakdown:

There is a sound of liquid owing in the freezer It is the

sound of refrigerant owing in the circulating pipeline of the

refrigerating system.

- It is normal.

Too noisy

- The freezer is not installed in a level ground.

- Change the position.

The refrigerating system does not work for a It is an indicator

of high quality for its long time but the inside temperature is

very good insulation and low cooling retention low.

- It is normal.

Produkt Specifikationer

Mærke:	Scandomestic
Kategori:	Køling frysning
Model:	SD 46

Har du brug for hjælp?

Hvis du har brug for hjælp til Scandomestic SD 46 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Køling frysning Scandomestic Manualer

Scandomestic SD 46 Manual

31 Juli 2024

Køling frysning Manualer

Nyeste Køling frysning Manualer

Liebherr KBgw 3864 Premium BioFresh Manual

15 Januar 2025

Liebherr UK1414 Manual

15 Januar 2025

Liebherr GWK 211 Manual

15 Januar 2025

Inventum IVR0881S Manual

15 Januar 2025

Miele kt 2211 Manual

15 Januar 2025

Bauknecht GKIE3883 Manual

15 Januar 2025

Atag ka 210 d Manual

15 Januar 2025

Liebherr ICUNS 3314 Manual

15 Januar 2025

Whirlpool arc 0500 Manual

15 Januar 2025

Candy CV 200 Manual

15 Januar 2025