Schneider MTN663991 Manual

Schneider Termostat MTN663991

Læs gratis den danske manual til Schneider MTN663991 (1 sider) i kategorien Termostat. Denne vejledning er vurderet som hjælpsom af 14 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 7.5 anmeldelser. Har du et spørgsmål om Schneider MTN663991, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

DANGER

Risk of fatal injury due to electrical current.

All work on the device should only be carried out

by skilled electrician. Observe the country-

specific regulations as well as the valid KNX

guidelines.

The KNX brightness and temperature sensor (referred

to as sensor in the following) is suitable for brightness

and temperature measurement in KNX building system

technology. The measured values are sent to the bus.

Measurement range for brightness measurement:

1 to 100,000 lux (± 20% or ± 5Lux)

Measurement range for temperature measurement:

-25°C to +55°C (± 5% or ± 1 degree)

|The larger tolerances are applicable for

brightness and temperature measurement.

AProgramming LED

BProgramming button

CBus connecting terminal

For your safety

Getting to know the sensor

Connections, displays and operating

elements

WARNING

Risk of fatal injury from electrical current.

The device could become damaged.

Safety clearance must be guaranteed in

accordance with IEC 60664-1. There must be at

least 4 mm between the individual cores of the

230 V supply cable and the KNX cable.

½CAUTION

The device could become damaged.

Moisture and dirt can penetrate the housing. This

can result in device failure and a short circuit on

the bus line. Always install the device vertically

with the screw fitting facing downwards.

1Fix the sensor.

2Aligne the sensor.

How to install the sensor

230 V

4 mm

KNX

6 mm 14 mm

25 mm

1Push the bus cable through the gasket into the

terminal compartment.

|Observe the correct polarity during connection.

2Connect KNX.

3Connect the bus voltage.

The LED flashes.

1Press the programming button.

The programming LED lights up.

2Load the physical address and application into the

device from the ETS.

The programming LED goes out.

The application has been loaded successfully, the

device is operative.

|When the device is operative, the LED stops

flashing approximately 10 seconds after

connecting the bus voltage or after loading the

application. Otherwise an invalid application

program has been loaded.

Cover installation:

1Carefully fit the cover on the installed device.

2Screw on the cover.

Cover care:

Clean the cover at regular intervals so that dirt does not

generate inaccurate brightness measurement values.

|Use a damp cloth for cleaning.

If you have technical questions, please contact the

Customer Care Center in your country.

www.schneider-electric.com

This product must be installed, connected and used in

compliance with prevailing standards and/or installa-

tion regulations. As standards, specifications and de-

signs develop from time to time, always ask for

confirmation of the information given in this publica-

tion.

Schneider Electric Industries SAS

How to connect the sensor

How to operate the sensor

How to installation and care the cover

Technical data

KNX: DC 24 V

Measurement range

Temperature: -25°C to +55°C

(± 5 % or ± 1 degree)

Brightness: 1 to 100,000 lux

(± 20 % or ± 5 lux)

Power consumption: < 150 mW

Type of protection

when installed:

IP 54 when installed vertically

with cover

KNX brightness and temperature sensor

Operating instructions

Art. no. MTN663991

V6639-562-00 03/08

Produkt Specifikationer

Mærke:	Schneider
Kategori:	Termostat
Model:	MTN663991

Har du brug for hjælp?

Hvis du har brug for hjælp til Schneider MTN663991 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Termostat Schneider Manualer

Schneider MTN6215-0310 Manual

10 August 2024

Schneider CCT593011 Manual

4 December 2023

Schneider CCTFR6100Z3 Manual

20 August 2023

Schneider MTN663991 Manual

5 Juni 2023

Schneider CCT15841 Manual

1 Juni 2023

Schneider WDE002963 Manual

16 Maj 2023

Schneider DTH-16 Manual

3 December 2022

Schneider WDE002478 Manual

16 November 2022

Schneider CCT15834 Manual

19 Oktober 2022

Termostat Manualer

Nyeste Termostat Manualer

Essentials MATRIX Manual

2 December 2025

Honeywell CT62B Manual

1 December 2025

Honeywell X2P RTH20B Manual

28 November 2025

Honeywell RTH2CWF Manual

27 November 2025

Honeywell CT60A1036 Manual

27 November 2025

Honeywell RLV4300A1005 Manual

27 November 2025

Honeywell RTH11B Manual

27 November 2025

Honeywell RLV210A1002 Manual

27 November 2025

Delta Dore Tybox Control XL Manual

27 November 2025

Honeywell T10+ Pro THX321WF2003W/U Manual

26 November 2025