Scosche GM1488B Manual

Scosche Bilsæt GM1488B

Læs gratis den danske manual til Scosche GM1488B (2 sider) i kategorien Bilsæt. Denne vejledning er vurderet som hjælpsom af 19 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 10 anmeldelser. Har du et spørgsmål om Scosche GM1488B, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

IN-DASH INSTALLATION KIT FOR

1988-03 FULL SIZE PICKUP/SPORT UTILITY

If you have any further questions, call

LIABILITY DISCLAIMER

This instruction booklet is based on carefully documented data and research of automobile dash disassembly, wire

harness/codes and information pertaining to installation of this kit (GM1488) in 1988-03 General Motors Vehicles.

Scosche Industries, Inc. can not be held responsible for discrepancies/inconsistencies that may occur due to the

automobile manufacturing changes or options, or damage that may occur in the automobile during the installation of

components while using this booklet.

SI 12/06 - GM1488 (3000317)

TECH HELP 1-800-621-3695 x 3

GM1488

CADILLAC

1999-02 ESCALADE

2002-02 ESCALADE EXR

CHEVROLET

1996-02 ASTRO VAN

2001-02 AVALANCHE

1992-94 BLAZER FULL SIZE

1992-99 CREW CAB / DOOLEY PICKUP

1996-00 EXPRESS VAN

1988-02 PICKUP FULL SIZE

1992-02 SUBURBAN

1995-02 TAHOE

GMC

1992-00 CREW CAB / DOOLEY PICKUP

1988-02 PICKUP FULL SIZE

1996-03 SAFARI

1996-00 SAVANNA

1992-02 SUBURBAN

1992-02 YUKON

1999-99 YUKON DENALI

2000-02 YUKON XL

#2006

MOUNTING

PANEL

#2224R

MOUNTING

CLIP (RIGHT)

#2224L

MOUNTING CLIP

(LEFT)

#1869/2543

MOUNTING

PANEL

HEX NUT

CARRIAGE

BOLT

1996-02 Chevrolet Astro Van

1996-03 GMC Safari Van

RADIO REMOVAL:

1. Extract (2) T-30 torx bolts, one from each side of the top console area and pop out top half of center

console assembly.

2. Extract (2) 9/32" hex screws from the bottom edge of the driver’s side under dash panel and (1) screw

from left dash below defroster vent.

3. Carefully pry underdash panel out to release, and use caution when handling parking brake release cable.

4. Insert key into "on", adjust shifter down (low gear), Pull outward on the instrument/radio panel to release

clips. Unplug switches, and remove panel.

5. Push down on side tabs securing radio, slide out of dash, unplug, and remove radio.

1996-00 Chevrolet Express Van

1996-00 GMC Savanna

RADIO REMOVAL:

1. Carefully pull out on dash instrument/radio dash bezel to release spring clips, unplug connectors and

remove panel.

2. Compress the two plastic side radio mounting clips, slide radio out of dash, unplug connectors and remove

radio.

INTRODUCTION / PRELIMINARY

This premium installation kit is for 1988-03 Full Size Pickup/Sport Utility vehicles. Included are all the parts

you need to mount your car stereo/cassette or CD player into your vehicle's dash. Refer to the individual

instruction in this manual to remove your vehicle's factory radio and assemble the kit.

CAUTION:

DISCONNECT YOUR VEHICLE'S NEGATIVE BATTERY TERMINAL BEFORE THE INSTALLATION TO HELP

PREVENT ELECTRICAL DAMAGE. WE RECOMMEND THE USE OF A VOLT/OHM METER OVER A TEST LIGHT TO

CHECK WIRING. A TEST LIGHT OR GROUNDED WIRE PROBE CAN CAUSE DAMAGE TO THE VEHICLE'S

COMPUTER AND/OR DIAGNOSTIC SYSTEMS. AVOID ALL FACTORY AIRBAG WIRING - AIRBAGS CAN

ACCIDENTALLY DEPLOY CAUSING SERIOUS INJURY OR DEATH.

NOTES:

• See your vehicle's instructions for any special tools your installation might require.

• Read all instructions accompanying your car stereo/cassette player for proper wiring and mounting

instructions.

CAR STEREO CONNECTORS

PROVIDE EASY CONNECTION OF YOUR CAR

STEREO TO FACTORY WIRING HARNESS.

GM02B

1988-Up

FACTORY WIRING CODES

GM02B

MDA-1B

Antenna Adaptor

MDA-1B

1992-94 Chevrolet Blazer

1992-99 Chevrolet Crewcab Dually

1992-00 GMC Crewcab Dually

1988-02 Chevrolet / GMC

Full Size Pickup

1992-02 Chevrolet / GMC Suburban

1999-02 Cadillac Escalade

2002-02 Cadillac Escalade EXT

2001-02 Chevrolet Avalanche

1995-99 Chevrolet Crewcab /

Dually Pickup

RADIO REMOVAL:

1. Engage parking brake.

2. Place key in ignition and depress brake to shift vehicle in to lowest gear.

This will allow the gear shift arm to be out of the way.

3. Carefully pull out on dash instrument/radio dash bezel to release

spring clips, unplug connectors and remove panel.

4. Compress the two plastic side radio mounting clips, slide

radio out of dash, unplug connectors and remove

radio.

NOTE: Use caution when removing the dash bezel over

the hazard switch. The hazard switch may need to be

pushed down as if to activate the hazard lights to allow

the bezel to slide over it.

NOTE (2): It is recommended that you use the Scosche GM02

factory connector and the MDA-1 antenna adapter to eliminate

the need to cut any of the factory plugs.

STEREO INSTALLATION/KIT PREPARATION:

Panel #2006 panel preparation:

1. Remove the metal fastening clips from the bottom

of the factory dash bezel and attach them to the

same location on the #2006 panel. (See

Illustration B)

2. Remove the A/C vents from the factory dash

bezel by releasing the spring fastening clips

securing them into the bezel.

3. Mount the vents into the kit by inserting the inner

edge of the vent into the center inside pivot hole.

Then insert the outer edge of the vent into the

outer pivot hole. Using the same metal spring

clips and mounting procedures from the original

truck panel to mount the vents to the new

#2006 panel.

STEREO INSTALLATION WITH THE 2006 PANEL:

1. Install the 2006 panel into the dash by inserting

the top mounting clips into the slots in the dash

and pushing up to snap them in. Then press the

bottom clips into the slots at the bottom of the

dash to secure the kit to the dash.

2. See illustration C for stereo mounting

configurations.

STEREO INSTALLATION WITH THE 1869/2543 PANEL

1. Attach the left and right side brackets to the

mounting panel with the carriage bolts

and nuts provided.

2. See illustration D for stereo mounting

configurations.

#1869/2543

MOUNTING PANEL

SHAFT RADIO'S

SUPPLIED FACEPLATE

RADIO'S SUPPLIED

TRIMPLATE

SHAFT RADIO

SNAP SHAFT TABS:

(SEE NOTE)

#2224R

MOUNTING

CLIP

#2224L

MOUNTING

CLIP

RADIO'S REAR

SUPPORT STRAP

STEREO INSTALLATION/KIT PREPARATION

ILLUSTRATION D

DIN

STEREO

RADIO'S REAR

SUPPORT STRAP

#1869 / 2543

MOUNTING

PANEL

RADIO'S

MOUNTING

SLEEVE

RADIO'S SUPPLIED

TRIMPLATE

BEND

TABS

OUT-

WARD

RADIO'S

SUPPLIED

TRIMPLATE

#2006

MOUNTING

PANEL

RADIO'S

MOUNTING

SLEEVE

DIN

STEREO

BEND

TABS

OUT-

WARD

ILLUSTRATION C

ILLUSTRATION B

REAR

VIEW

OF KIT

METAL

FASTENING

CLIP

DASH BEZEL/TUNER PACK REMOVAL:

1. Carefully remove the factory tape/EQ (or pocket) bezel by prying out along the

bottom to release fastening clips. Then carefully pull down on the bezel to

release the fasteners securing the top and remove the bezel.

2. Extract the two (2) screws securing the factory tape player/equalizer (when

equipped).

3. Remove the dash panel under the steering column by extracting the

two (2) screws securing it to the dash.

4. Locate the radio tuner pack (metal control box) under the

dash above the accelerator pedal. Remove it by extracting

the three (3) screws securing it to the underdash brackets.

5. Unplug all the connectors going into the radio tuner pack and

remove it from the vehicle.

6. Pull the tape player/equalizer from the dash and carefully pull

the plug harness through the dash from the radio tuner pack

location and remove the tape player/equalizer form the dash.

7. Locate the antenna plug and the plugs that were connected to the top of the radio tuner pack. Route them

into the tape player/equalizer cavity. These are the factory power, speaker and antenna plugs that will be

used for the aftermarket radio hook-ups.

NOTE: It is recommended that you use the Scosche GM02 factory connector and the MDA-1 antenna

adapter to eliminate the need to cut any of the factory plugs.

OPTIONAL FACTORY RADIO DISPLAY/CONTROL UNIT REMOVAL AND POCKET REPLACEMENT:

1. Extract the (4) screws securing the instrument cluster dash bezel to the dash.

2. Pull the dash bezel from the dash, disconnect all the connectors and remove the bezel.

3. Extract the (4) screws securing the heater controls to the dash and pull it out of the dash cavity.

4. Extract the (4) screws securing the radio to the dash and pull from the cavity.

5. Route the radio leads from the tuner location as mentioned in step 4 of tape player/equalizer removal and

remove the radio.

6. Install the optional pocket (Scosche part #1001518) by reversing procedures 1 through 4.

1995-02 Chevrolet / GMC Full Size Pickup

1992-02 Chevrolet / GMC Suburban

1995-02 Chevrolet Tahoe

1995-00 GMC Crewcab / Dually Pickup

1992-02 GMC Yukon

1999-99 GMC Yukon Denali

2000-02 GMC Yukon XL

CAUTION:

REAR SUPPORT IS

ESSENTIAL TO THE

INSTALLATION'S

STRUCTURAL

INTEGRITY.

NOTE: SNAP SHAFT MOUNTING

TABS NOT INCLUDED. IF

REQUIRED FOR YOUR STEREO

INSTALLATION, CALL

800-621-3695 X3 FOR IMMEDIATE

SHIPMENT

Produkt Specifikationer

Mærke:	Scosche
Kategori:	Bilsæt
Model:	GM1488B

Har du brug for hjælp?

Hvis du har brug for hjælp til Scosche GM1488B stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Bilsæt Scosche Manualer

Scosche HA1714B Manual

28 December 2024

Scosche BTFreq Pro Manual

5 September 2024

Scosche KA2091B Manual

21 August 2024

Scosche auxMIC Manual

21 August 2024

Scosche KA2070B Manual

21 August 2024

Scosche NN1640B Manual

21 August 2024

Scosche TA2074B Manual

21 August 2024

Scosche TA2077B Manual

21 August 2024

Scosche TA2079B Manual

21 August 2024

Scosche HA1709B Manual

20 August 2024

Bilsæt Manualer

Nyeste Bilsæt Manualer

Metra 99-8270HG Manual

3 April 2025

Metra 99-8722B Manual

3 April 2025

Metra 99-7802CH Manual

3 April 2025

Metra 99-8214TG Manual

3 April 2025

ZZ-2 IC-SYM Manual

1 April 2025

Metra 99-4000 Manual

31 Marts 2025

Exibel INBTK006 Manual

14 Januar 2025

Metra 95-5026 Manual

28 December 2024

Metra 95-7883HG Manual

28 December 2024

Metra 99-7339B Manual

28 December 2024