Sekonda Crossfell Digital 30165 Manual

Sekonda Ur Crossfell Digital 30165

Læs gratis den danske manual til Sekonda Crossfell Digital 30165 (2 sider) i kategorien Ur. Denne vejledning er vurderet som hjælpsom af 27 personer og har en gennemsnitlig bedømmelse på 3.9 stjerner ud af 14 anmeldelser. Har du et spørgsmål om Sekonda Crossfell Digital 30165, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/2
IS47K
Light
Mode
Reset
Start
Calendar
Battery (CR2025)
Press “C” to on/off the alarm ( ) and snooze
Press and hold “C” until the hour digit begins
to flash. This selects the hour for adjustment.
Press “D” to increase the hour. Press and hold
“D” to increase at high speed.
Press “B” again to select the minutes. Press
“D” to increase the minutes. Press and hold
“D” to increase at high speed.
Press “B” again to select the month. Press
“D” to adjust.
Press “B” again to select the date. Press “D”
to adjust.
Press “C” to exit the setting mode.
Alarm - Stopwatch - Dual Time - Timer - Time/Date
MODE SELECTION
BUTTONS
50M Water Resistant
ALARM
STOPWATCH
DUAL TIME
TIMER
a
b
c
d
TIME/DATE SETTING
e
ALARMa
1.
2.
3.
4.
5.
6.
From real time mode press “B” to switch to Alarm
mode. “AL” will be displayed at the top of the
screen.
• Hourly chime setting
• The alarm sounds at the preset time each day
• Snooze function
• 1/100 second unit
• Measuring range: 0hrs 00’00”00 - 23hrs 59’59”99
• Set a dierent time zone
Press “B” to change the mode in the following
sequence:
•12hr/24hr time format
•Seconds, Hours, Minutes, Year, Month, Date
•Calendar
•Set a countdown from 1 minute up to 24hrs
•Alarm will sound when the timer reaches 0
•Button operations are indicated using the letters
shown on the below illustration.
Never try to open the case or remove its back
cover.
Do not operate the buttons under water.
Should moisture appear inside the watch, have it
checked immediately by your dealer. Otherwise it
can cause erosion of the metal parts of the watch.
Although the watch is designed to withstand normal
use, you should avoid rough use or dropping the
watch.
Avoid exposing the watch to extreme temperatures.
Wipe the watch with a dry and soft cloth only. Avoid
allowing it to come into direct contact with chemical
materials that can cause deterioration of the plastic
parts of the watch.
Avoid wearing the watch in electromagnetic or
static conditions.
1.
2.
3.
4.
5.
6.
7.
Hourly Chime Setting
Alarm Time Setting
Snooze Function
With the month and date left blank, the alarm
will sound at the time set every day.
The alarm will sound for 10 seconds at the set
time. Press any button to turn the alarm off.
•With the snooze (Snz) function turned on, when
the alarm sounds, press any button to snooze
the alarm for 5 minutes.
•The alarm will sound 5 minutes later, and stop
automatically after sounding for 10 seconds.
• Press any button to snooze for a further 5
minutes.
•From the alarm mode screen, press “D” to
switch to the hourly chime setting screen
( :00 will be displayed).
•Press “C” to on/off the hourly chime ( )
• The chime will sound on the hour, every hour,
until turned off.
50
When in real time mode, press and hold “C”
until the seconds begin to flash. This selects
the seconds for adjustment.
Press “D” to reset the seconds.
Press “B” to select the hour. Press “D” to
increase the hour. Press and hold “D” to
increase at high speed.
Press “B” again to select the minutes. Press
“D” to adjust the minutes. Press and hold
“D” to adjust at high speed.
Press “B” again to show the year. Press “D”
to increase the year. Press and hold “D” to
adjust at high speed. The year can be set
between 2000-2099.
Press “B” again to select the month. Press
“D” to adjust the month. Press and hold “D”
to adjust at high speed.
Press “B” again to select the date. Press “D”
to adjust the date. Press and hold “D” to
adjust at high speed.
Press “C” to exit the time/date setting
mode.
STOPWATCH
b
DUAL TIMEc
TIME/DATE SETTING
e
BACKLIGHT
DISPLAY
TIMERd
Setting the Timer
Setting the Time/Date
Setting the Dual Time
Press and hold “C” until the hour digit begins
to flash. This selects the hour for adjustment.
Press “D” to increase the hour. Press and
hold “D” to increase at high speed.
Press “B” again to select the minutes. Press
“D” to increase the minutes. Press and hold
“D” to increase at high speed.
Press “C” to exit the setting screen.
Press “D” to start the countdown.
To pause the countdown press “D”. Press “D”
again to resume the countdown.
While paused, press “C” to reset the
countdown.
•Timers can be set to countdown from 1 minute
up to 24 hours.
•When the timer reaches zero, the alarm will
sound for 15 seconds.
• Press any key to stop the alarm, and the timer
will automatically reset.
1.
2.
3.
4.
5.
6.
7.
1.
2.
3.
4.
5.
6.
7.
8.
1.
2.
3.
4.
To set the countdown to a time period of 24
hours, set it to 0:00 00
While the timer is running, press “B” to switch
modes. The timer will continue to run.
From real time mode press “B” three
times to switch to Dual Time mode.
“DT” will be displayed at the top of
When in real time mode, press “D” to switch
between 12hr and 24hr time modes.
“24h” will be displayed in the top left of the
screen in 24hr mode, and “PM” will be displayed
to the left of the hour after midday in 12hr mode.
From real time mode press “B”
four times to switch to Timer mode.
“TR” will be displayed at the top of
From real time mode press “B” twice
to switch to Stopwatch mode. “ST”
will be displayed at the top of the
Press “B” twice to return to real time mode.
Press and hold “C” until the hour digit
begins to flash. Press “D” to set the hour.
Press “B” to select the next part you want to
set and press “D” to set.
Once you have set the time, press “C” to
exit the setting screen.
Using the EL Backlight
Lap Time
Split Time
Press “D” to start the stopwatch.
Press “D” again to stop the stopwatch.
Press “C” to reset the stopwatch to zero.
Press “D” to start the stopwatch.
Press “C” to display the split time. “SPL”
will be displayed at the top of the screen.
The stopwatch will continue timing
internally.
Press “C” again to continue timing.
Repeat steps 2 and 3 to measure multiple
split times.
When “SPL” is displayed, press “D” to exit
split time and stop the stopwatch.
Press “C” to reset the stopwatch.
1.
2.
3.
1.
2.
3.
4.
5.
6.
The backlight uses an electro-luminescent that
causes the display to glow for easy reading in
the dark.
In any mode, press “A” to illuminate the digital
display for about 3 seconds.

Produkt Specifikationer

Mærke: Sekonda
Kategori: Ur
Model: Crossfell Digital 30165

Har du brug for hjælp?

Hvis du har brug for hjælp til Sekonda Crossfell Digital 30165 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ur Sekonda Manualer

Sekonda

Sekonda Pacific Wave 30117 Manual

13 August 2025
Sekonda

Sekonda Velocity 30023 Manual

13 August 2025
Sekonda

Sekonda Speed Dual Time 30111 Manual

13 August 2025
Sekonda

Sekonda Crossfell Digital 30165 Manual

13 August 2025
Sekonda

Sekonda Armstrong Moon Phase 30147 Manual

13 August 2025
Sekonda

Sekonda Circuit 30254 Manual

12 August 2025
Sekonda

Sekonda Dress 1634 Manual

8 Maj 2024

Ur Manualer

Nyeste Ur Manualer

Invicta

Invicta Bolt 26526 Manual

10 Oktober 2025
Invicta

Invicta Angel 28738 Manual

10 Oktober 2025
Invicta

Invicta Angel 28656 Manual

10 Oktober 2025
Invicta

Invicta Bolt 31354 Manual

10 Oktober 2025
Invicta

Invicta Angel 29086 Manual

10 Oktober 2025
Invicta

Invicta Coalition Forces 25330 Manual

10 Oktober 2025
Invicta

Invicta Character Collection 24904 Manual

10 Oktober 2025
Invicta

Invicta Aviator 21740 Manual

10 Oktober 2025
Invicta

Invicta Character Collection 24825 Manual

10 Oktober 2025
Invicta

Invicta Angel 30967 Manual

10 Oktober 2025