Séura SC-1 Manual
Séura
Ikke kategoriseret
SC-1
Læs gratis den danske manual til Séura SC-1 (20 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 24 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 12.5 anmeldelser. Har du et spørgsmål om Séura SC-1, eller vil du spørge andre brugere om produktet?
Side 1/20
OUTDOOR TV
CEILING MOUNT
INSTALLATION GUIDE
Model Numbers:
SC-1
LC-1
WARRANTY REGISTRATION
REGISTER FOR
EXTRA BENEFITS
Activate within 30 days of purchase:
seura.com/activate
14
15
16
" FULLY COLLAPSED
22-15/16" FULLY EXTENDED
17
15
16
"
25mm
1"
5
16
" X
13
16
"
4
1
8
"
4
7
8
"
5"
5
3
4
"
6
1
2
"
6
1
2
"
4
5
16
"
29
7
16
" FULLY COLLAPSED
51-7/16" FULLY EXTENDED
17
15
16
"
25mm
1"
4
5
16
"
17
15
16
"
25mm
1"
Optional: Us ing the keyhole loc ations, drill
the additiona l holes for the sup port screws.
Insert and fa sten two screws w ithout
washers until approximately 1/2" remains.
O
p
t
i
o
n
a
l
K
e
y
h
o
l
e
S
l
o
t
O
p
t
i
o
n
a
l
K
e
y
h
o
l
e
S
l
o
t
2
Prior to the installation of this product, read all
instructions. Keep this manual for future reference.
This product is designed to mount televisions
and any accessories weighing up to 200 lbs. to a
properly rated ceiling structure.
CAUTION DO NOT EXCEED MAXIMUM LISTED
WEIGHT CAPACITY. SERIOUS INJURY OR PROPERTY
DAMAGE MAY OCCUR.
Warnings:
• Safety measures must be practiced at all times
during the assembly of this product. Use proper
safety equipment and tools for the assembly
procedure to prevent personal injury.
• At least two qualied people should perform the
assembly procedure. Proper installation must
be followed as outlined in these installation
instructions. Personal injury and/or property
damage can result from dropping or mishandling
the TV.
• Ensure that there are no missing or defective
parts upon receipt. Never use defective parts.
• This product contains small parts that could be
a choking hazard.
• The ceiling you afx the Séura mount to must
be capable of supporting ve times the weight
of the television and the mount combined. A
professional installer or structural engineer
should inspect or verify the requirements of
the wall.
• Do not use this product for any purpose other
than to mount a VESA compliant TV on a vertical
surface as outlined in this manual.
• When mounting to metal structures or concrete
ceilings, an alternative anchor (not included)
should used.
• Always inspect mounting location for electrical
wires, water, and natural gas lines prior to
installation. Cutting or drilling into these utility
lines may cause serious personal injury or
property damage.
• Do not install near sources of high heat.
• Do not install on a structure that is prone to
vibration, movement or chance of impact.
Note: The included hardware is for mounting to
vertical concrete surfaces or wood trusses and
ceiling structures. If you are uncertain about the
nature of your wall, please consult your hardware
or installation professional for proper mounting to
types of walls.
Safety
Compatible with Séura Outdoor TVs:
Shade Series: SHD1-55, SHD1-65, SHD1-75, SHD2-43, SHD2-55, SHD2-65, SHD2-75
Ultra Bright: STM3-55-U, STM3-65-U, STM3-86-U
WARNING: Cancer and Reproductive
Harm: www.p65warnings.ca.gov.
3
Parts and Tools Required (not included)
The following tools may be required depending on your particular installation. They are not included.
P5080T
Installation Instructions
Visit the Premier Mounts website at http://www.premiermounts.com Page 3
Parts List
Installation Tools
The following tools may be required depending upon your particular installation. They are not included.
Pencil
Level
¼˝ Drill Bit for
Wood Stud
Electronic Stud Finder
Socket Wrench
Phillips Tip Screwdriver
Tape Measure
Hand Held Drill
Hammer**
3
/8 ˝ Concrete Drill Bit*
Protective Eyewear
* Optional tools for concrete installations.
½˝ Socket
M10 Socket*
2
1
5
/16
˝ x 3˝ Lag Bolts
(Qty 6)
Thread Depth Indicator
(Qty 1)
Universal Spacers
Finned Anchors
(Qty 6)
(Qty 24)
5
/16
˝ Flat Washers
(Qty 6)
Pro Mounting Hardware
Universal Washers
(Qty 6)
Security Barrel
(Qty 1)
Wall Plate
(Qty 1)
Universal Tilt Brackets
(Qty 2)
M6 x 60mm Screws
(Qty 2)
1/2”
1/2”
1/2”
1/2”
Level
Stud Sensor
(edge-to-edge stud
nder is recommended)
Tape Measure
7/32” Drill Bit 7/16” Masonry Drill Bit
Socket Wrench
½” Socket
½” Combination
Wrench
Pencil Power Drill Philips #2
Screwdriver
(6mm Allen Wrench
for use with 86”
Ultra Bright TV size)
For Wood Truss Installation For Concrete, Brick and Stone Installation
1/2”
1/2”
1/2”
1/2”
1/2”
4
Ceiling Bracket
Ceiling Bracket
Extension
(length varies by model)
Mounting Plate Rails
Parts Included
Before using the device, please check the following contents of the box for completeness. Illustrations are
not to scale. If any parts are missing or damaged, contact Séura.
Manual
OUTDOOR TV
CEILING MOUNT
INSTALLATION GUIDE
Model Numbers:
SC-1
LC-1
WARRANTY REGISTRATION
REGISTER FOR
EXTRA BENEFITS
Activate within 30 days of purchase:
seura.com/activate
Mounting Template
(located on inside bottom of box)
14
15
16
" FULLY COLLAPSED
22-15/16" FULLY EXTENDED
17
15
16
"
25mm
1"
5
16
" X
13
16
"
4
1
8
"
4
7
8
"
5"
5
3
4
"
6
1
2
"
6
1
2
"
4
5
16
"
29
7
16
" FULLY COLLAPSED
51-7/16" FULLY EXTENDED
17
15
16
"
25mm
1"
4
5
16
"
17
15
16
"
25mm
1"
Optional: Using the keyhole lo cations, drill
the additional holes for the su pport screws.
Insert and fasten two screw s without
washers until approximately 1/2" remains.
O
p
t
i
o
n
a
l
K
e
y
h
o
l
e
S
l
o
t
O
p
t
i
o
n
a
l
K
e
y
h
o
l
e
S
l
o
t
14
15
16
" FULLY COLLAPSED
22-15/16" FULLY EXTENDED
17
15
16
"
25mm
1"
5
16
" X
13
16
"
4
1
8
"
4
7
8
"
5"
5
3
4
"
6
1
2
"
6
1
2
"
4
5
16
"
29
7
16
" FULLY COLLAPSED
51-7/16" FULLY EXTENDED
17
15
16
"
25mm
1"
4
5
16
"
17
15
16
"
25mm
1"
Option al: Usin g the keyho le locations, d rill
the addi tional h oles fo r the supp ort scr ews.
Inser t and fas ten two screws wit hout
washers until approximately 1/2" remains.
O
p
t
i
o
n
a
l
K
e
y
h
o
l
e
S
l
o
t
O
p
t
i
o
n
a
l
K
e
y
h
o
l
e
S
l
o
t
14
15
16
" FULLY COLLAPSED
22-15/16" FULLY EXTENDED
17
15
16
"
25mm
1"
5
16
" X
13
16
"
4
1
8
"
4
7
8
"
5"
5
3
4
"
6
1
2
"
6
1
2
"
4
5
16
"
29
7
16
" FULLY COLLAPSED
51-7/16" FULLY EXTENDED
17
15
16
"
25mm
1"
4
5
16
"
17
15
16
"
25mm
1"
Option al: Usin g the keyho le locations, d rill
the addi tional h oles fo r the supp ort scr ews.
Inser t and fas ten two screws wit hout
washers until approximately 1/2" remains.
O
p
t
i
o
n
a
l
K
e
y
h
o
l
e
S
l
o
t
O
p
t
i
o
n
a
l
K
e
y
h
o
l
e
S
l
o
t
14
15
16
" FULLY COLLAPSED
22-15/16" FULLY EXTENDED
17
15
16
"
25mm
1"
5
16
" X
13
16
"
4
1
8
"
4
7
8
"
5"
5
3
4
"
6
1
2
"
6
1
2
"
4
5
16
"
29
7
16
" FULLY COLLAPSED
51-7/16" FULLY EXTENDED
17
15
16
"
25mm
1"
4
5
16
"
17
15
16
"
25mm
1"
Option al: Usin g the keyho le locations, d rill
the addi tional h oles fo r the supp ort scr ews.
Inser t and fas ten two screws wit hout
washers until approximately 1/2" remains.
O
p
t
i
o
n
a
l
K
e
y
h
o
l
e
S
l
o
t
O
p
t
i
o
n
a
l
K
e
y
h
o
l
e
S
l
o
t
(4) 5/16”
Stainless Steel
Flat Washers
P5080T
Installation Instructions
Visit the Premier Mounts website at http://www.premiermounts.com Page 3
Parts List
Installation Tools
The following tools may be required depending upon your particular installation. They are not included.
Pencil
Level
¼˝ Drill Bit for
Wood Stud
Electronic Stud Finder
Socket Wrench
Phillips Tip Screwdriver
Tape Measure
Hand Held Drill
Hammer**
3
/8 ˝ Concrete Drill Bit*
Protective Eyewear
* Optional tools for concrete installations.
½˝ Socket
M10 Socket*
2
1
5
/16
˝ x 3˝ Lag Bolts
(Qty 6)
Thread Depth Indicator
(Qty 1)
Universal Spacers
Finned Anchors
(Qty 6)
(Qty 24)
5
/16
˝ Flat Washers
(Qty 6)
Pro Mounting Hardware
Universal Washers
(Qty 6)
Security Barrel
(Qty 1)
Wall Plate
(Qty 1)
Universal Tilt Brackets
(Qty 2)
M6 x 60mm Screws
(Qty 2)
(6) 1/4-20x1/2 Stainless
Steel Security Torx
Screws
44"
17
15
16
"
1"
4
5
16
"
14"
14"
5
13
16
"
5
13
16
"
5
13
16
"
5
13
16
"
1
2
" X 1"
20
5
16
"
26
1
4
"
14" 14"
(2) 1/4-20 Knobs
44"
17
15
16
"
1"
4
5
16
"
14"
14"
5
13
16
"
5
13
16
"
5
13
16
"
5
13
16
"
1
2
" X 1"
20
5
16
"
26
1
4
"
14" 14"
6
14
15
16
" FULLY COLLAPSED
22-15/16" FULLY EXTENDED
17
15
16
"
25mm
1"
5
16
" X
13
16
"
4
1
8
"
4
7
8
"
5"
5
3
4
"
6
1
2
"
6
1
2
"
4
5
16
"
29
7
16
" FULLY COLLAPSED
51-7/16" FULLY EXTENDED
17
15
16
"
25mm
1"
4
5
16
"
17
15
16
"
25mm
1"
Optional: Using t he keyhole locations, drill
the additional holes for the suppor t screws.
Inser t and f asten two screws without
washers until approximately 1/2" remains.
O
p
t
i
o
n
a
l
K
e
y
h
o
l
e
S
l
o
t
O
p
t
i
o
n
a
l
K
e
y
h
o
l
e
S
l
o
t
Features
Ceiling
Mounting Plate
A template
with the
mounting hole
pattern is
included to aid
installation.
Tilt Locking Bolts
Allows for tilt
angle of the TV
adjustment.
Top Leveling
Screws
Allows for
leveling
adjustments
of the TV after
mounting.
Boom Locking Screws
Prevents the TV from being
removed or dislodged from
the mounting plate.
Directional
Mounting Arrows
The arrow lets you
know which edge
is up.
7
14
15
16
" FULLY COLLAPSED
22-15/16" FULLY EXTENDED
17
15
16
"
25mm
1"
5
16
" X
13
16
"
4
1
8
"
4
7
8
"
5"
5
3
4
"
6
1
2
"
6
1
2
"
4
5
16
"
29
7
16
" FULLY COLLAPSED
51-7/16" FULLY EXTENDED
17
15
16
"
25mm
1"
4
5
16
"
17
15
16
"
25mm
1"
Optional: Using t he keyhole locations, drill
the additional holes for the suppor t screws.
Inser t and f asten two screws without
washers until approximately 1/2" remains.
O
p
t
i
o
n
a
l
K
e
y
h
o
l
e
S
l
o
t
O
p
t
i
o
n
a
l
K
e
y
h
o
l
e
S
l
o
t
Height Adjustment
Use both included
screws to set the
desired height.
Cable Pass Through
Run power and
content cables
through the back of
the pole or into the
ceiling.
Cable Pass Through
Run power and
content cables
through the pole and
connect to the TV
inputs.
Swivel Adjustment
Loosening both
knobs allows
adjustment of the
swivel. Always
retighten as TV may
swivel in the wind.
8
Step 1: Assemble and Prepare Mount
1. Assemble ceiling mount
Ensure the plastic ring is on the Ceiling Bracket Extension. Slide the
Mounting Plate Rails onto the Ceiling Bracket Extension.
Note: The Mounting Plate Rails is a symmetrical part, so orientation
does not matter.
2. Aach the Ceiling Bracket
Slide the Ceiling Bracket Extension into the Ceiling Bracket. Using
two of the included security torx screws, tighten the extension onto
the desired height.
Attach two knobs and install into the wall plate mount rails.
To adjust the swivel angle
of the TV, loosen the two
thumb screws on the
back of the ceiling mount.
Adjust to the desired angle.
Tighten both screws.
44"
17
15
16
"
1"
4
5
16
"
14"
14"
5
13
16
"
5
13
16
"
5
13
16
"
5
13
16
"
1
2
" X 1"
20
5
16
"
26
1
4
"
14" 14"
Platic Ring
9
3. Aach mounting plate to ceiling mount
Using the four included fasteners, attach the mounting
plate to the ceiling mount rails as shown.
44"
17
15
16
"
1"
4
5
16
"
14"
14"
5
13
16
"
5
13
16
"
5
13
16
"
5
13
16
"
1
2
" X 1"
20
5
16
"
26
1
4
"
14" 14"
44"
17
15
16
"
1"
4
5
16
"
14"
14"
5
13
16
"
5
13
16
"
5
13
16
"
5
13
16
"
1
2
" X 1"
20
5
16
"
26
1
4
"
14" 14"
44"
17
15
16
"
1"
4
5
16
"
14"
14"
5
13
16
"
5
13
16
"
5
13
16
"
5
13
16
"
1
2
" X 1"
20
5
16
"
26
1
4
"
14" 14"
44"
17
15
16
"
1"
4
5
16
"
14"
14"
5
13
16
"
5
13
16
"
5
13
16
"
5
13
16
"
1
2
" X 1"
20
5
16
"
26
1
4
"
14" 14"
P5080T
Installation Instructions
Visit the Premier Mounts website at http://www.premiermounts.com Page 3
Parts List
Installation Tools
The following tools may be required depending upon your particular installation. They are not included.
Pencil
Level
¼˝ Drill Bit for
Wood Stud
Electronic Stud Finder
Socket Wrench
Phillips Tip Screwdriver
Tape Measure
Hand Held Drill
Hammer**
3
/8 ˝ Concrete Drill Bit*
Protective Eyewear
* Optional tools for concrete installations.
½˝ Socket
M10 Socket*
2
1
5
/16
˝ x 3˝ Lag Bolts
(Qty 6)
Thread Depth Indicator
(Qty 1)
Universal Spacers
Finned Anchors
(Qty 6)
(Qty 24)
5
/16
˝ Flat Washers
(Qty 6)
Pro Mounting Hardware
Universal Washers
(Qty 6)
Security Barrel
(Qty 1)
Wall Plate
(Qty 1)
Universal Tilt Brackets
(Qty 2)
M6 x 60mm Screws
(Qty 2)
10
Installation
IMPORTANT: THIS PRODUCT MUST BE MOUNTED TO A PROPERLY RATED CEILING STRUCTURE. The structure
must be able to support ve times the weight of the television and the mount combined. A professional
installer or structural engineer should inspect or verify the requirements of the wall.
CEILING MOUNT TEMPLATE
Refer to the included Installation Guide for complete instructions
Optional: Usin g the keyhole loca tions, drill
the additional h oles for the suppo rt screws.
Insert and fas ten two screws wit hout
washers until approximately 1/2" remains.
O
p
t
i
o
n
a
l
K
e
y
h
o
l
e
S
l
o
t
O
p
t
i
o
n
a
l
K
e
y
h
o
l
e
S
l
o
t
IMPORTANT: HANDLE THE TV IN A VERTICAL POSITION TO AVOID DAMAGE TO THE
SCREEN. IF PLACING THE TV SCREEN-SIDE DOWN OR LEANING AGAINST A WALL DURING
INSTALLATION, COVER THE SCREEN WITH A PROTECTIVE CLOTH OR BLANKET.
Step 2: Mount Ceiling Plate to Ceiling
1. Choose mounting location
Place the template in the desired location on
the ceiling.
Wood Joist/Truss Mounting:
At least four hole locations must be fastened
to joists/trusses or an appropriately stabilized
structure. Verify the center of the wood beam
using an edge-to-edge stud nder. Mark all
hole locations in the template slots with a
pencil on the ceiling.
Concrete, Stone or Brick:
All six hole locations must be fastened. Mark
all hole locations in the template slots with a
pencil on the ceiling.
11
CEILING MOUNT TEMPLATE
Refer to the included Installation Guide for complete instructions
Optional: Using the keyhole locat ions, drill
the additional h oles for the suppo rt screws.
Insert and fas ten two screws wit hout
washers until approximately 1/2" remains.
O
p
t
i
o
n
a
l
K
e
y
h
o
l
e
S
l
o
t
O
p
t
i
o
n
a
l
K
e
y
h
o
l
e
S
l
o
t
2. Drill pilot holes
Wood Joist/Truss Mounting:
Pre-drill the four marked holes on the wall 3-inches deep with a 7/32” drill bit.
Concrete:
Pre-drill the four marked holes on the wall 3-inches deep with a 7/16” masonry drill bit. Insert a plastic
anchor into each of these holes. If necessary, lightly tap each anchor into place with a hammer.
Optional: Using the
keyhole locations,
drill the additional
holes for the
support screws.
Insert and fasten
two screws without
washers until
approximately 1/2”
remains.
O
p
t
i
o
n
a
l
K
e
y
h
o
l
e
S
l
o
t
12
3. Aach ceiling mounting plate
Align the mounting plate with the pre-drilled holes. Ensure that the cable pass through holes on the
mount are positioned appropriately.
Wood Joist/Truss Mounting:
Align the bracket with the screw keyed slots
and turn to hold in place. Finish tightening all
lag screws with washers until they are snug with
the mounting surface. Do not over tighten the
lag screws. Tighten the lag screws only until the
washers are pulled rmly against the bracket.
Concrete:
Align the bracket with the pre-drilled holes.
Attach bracket to the ceiling using the six lag
screws and six at washers. Tighten all lag screws
using a socket wrench and ½” socket. Make sure
the anchor is seated completely ush with the
concrete surface even if there is another layer of
material, such as drywall. Do not over tighten the
lag screws. Tighten the lag screws only until the
washers are pulled rmly against the bracket.
13
Step 4: Hang the TV
IMPORTANT: NEVER TRY TO HANG A TV BY YOURSELF. ALWAYS USE AT LEAST TWO PEOPLE TO LIFT THE TV
INTO PLACE.
1. Lift the TV and bring the back of the TV towards
the mount, positioning it slightly above the
mounting plate.
2. Lower the TV to hook the bottom hooks of the
Tilt Mount TV Brackets on the lower rail of the
mounting plate.
3. Bring the top of the TV closer to the mount to
hook the top hooks of the Tilt Mount TV Brackets
on the top rail of the mounting plate.
4. Make sure the bottom and top rails are fully
engaged.
Do not let go of the TV until you are certain that the
top and bottom hooks of both mounting brackets
are securely engaged on the upper and lower
mounting rails of the mounting plate.
Séura recommends checking knobs, screws, and
bolts every 2-6 months. Temperature uctuations,
wind, and normal wear and tear can loosen
hardware over time.
Step 3: Aach Tilt Mount TV Brackets to TV
IMPORTANT: Check your TV manual before aaching brackets to TV. Some models require aaching
soundbar brackets in tandem with aaching TV brackets.
Using a Philips #2 Screwdriver (or 6 mm Allen Wrench for 86” Ultra Bright
TV), remove the four VESA mount screws from the back of the TV. Place
the two identical Tilt Mount TV Brackets at against the back of the
TV with the arrows pointed towards the top of the TV. Line the
brackets up with the VESA mount fastener locations. If
mounting a Séura Outdoor TV, reference page 14 for the
bracket hole that should be used on each Tilt Mount
TV Bracket. Attach the Tilt Mount TV Brackets to the
TV using the same four VESA mount screws that you
just removed.
26
1
4
"
20
5
16
"
11
7
16
"
25mm
1"
5
5
8
"
7"
1
15
16
"
Optional: If additional security
is desired for installation with back
access such as oor stands or ceiling
mounts, use the included torx security screws
to attach the brackets to the TV.
14
Top Leveling Screw
Allows for leveling
adjustments of the TV
after mounting.
Boom Locking Screw
Prevents the TV from
being removed or
dislodged from the
mounting plate.
Step 5: Adjust the TV
Séura recommends checking knobs, screws,
and bolts every two to six months. Temperature
uctuations, wind, and normal wear and tear can
loosen hardware over time.
Top leveling screw adjustment:
If your TV is not level, the two (2) top leveling screws
located on the top of the tilt mount TV brackets will
allow you to compensate for this tilt by adjusting
the screws with the provided T27 security torx
screwdriver.
1. Loosen both leveling screws (one on each bracket).
2. Adjust the tilt of your TV.
3. Tighten both leveling screws.
Do not overtighten the leveling screws.
Boom locking screw adjustment:
After you have adjusted leveling the TV, tighten the
two (2) bottom locking screws located on the bottom
of the tilt mount TV brackets (one on each bracket)
using the provided T27 security torx screwdriver.
Do not overtighten the locking screws.
26
1
4
"
20
5
16
"
11
7
16
"
25mm
1"
5
5
8
"
7"
1
15
16
"
Caution: It is possible to dislodge
your TV while you level it. Use
extreme caution until you tighten the
leveling and locking screws.
15
P5080T
Installation Instructions
Visit the Premier Mounts website at http://www.premiermounts.com Page 15
Leveling Screw Adjustment
If your at panel is tilted too far to one side, the leveling
screws will allow you to compensate for this tilt by
adjusting the screws with a screwdriver.
Loosen both locking screws.
®
Adjust the tilt of your at panel.
¯
Tighten both locking screws.
Caution!
It is possible to dislodge your at panel while you
level your at panel. Use extreme caution until
you tighten the locking screws.
Mounting Bracket Adjustments
Locking Screw Adjustment
After you have nished leveling your at panel, be sure
to tighten the two (2) M6 x 120mm locking screws.
Do not overtighten the locking screws.
M6 x 120mm
Locking Screw
(1 per Bracket)
M6 x 30mm
Leveling Screw
(1 per Bracket)
Tilt Adjustment
Adjusting the Flat Panel Friction Tilt Angle
Place one hand at the center-top edge of the at
panel.
®
Place the other hand on the center-bottom edge of
the at panel.
¯
Using the upper hand, gently pull the top of the
at panel towards you while the lower hand gently
pushes the bottom of the at panel away from you.
Adjusting the Flat Panel to the Original Position
Place one hand at the center-top edge of the at
panel.
®
Place the other hand on the center-bottom edge of
the at panel.
¯
Using the upper hand, gently push the top of the at
panel towards the wall while the lower hand gently
pulls the bottom of the at panel away from the wall.
Tilt adjustment:
Adjusting the TV Tilt Angle
1. Place one hand on the center-top edge
of the TV.
2. Place the other hand on the center-
bottom edge of the TV.
3. Using the upper hand, gently pull the top
of the TV towards you while the lower
hand gently pushes the bottom of the TV
away from you.
Adjusting the TV to the Original Position
1. Place one hand on the center-top edge
of the TV.
2. Place the other hand on the center-
bottom edge of the TV.
3. Using the upper hand, gently push the top
of the TV towards the wall while the lower
hand gently pulls the bottom of the TV
away from the wall.
After tilt is adjusted to the desired position,
tighten the (2) tilt locking bolts on each
bracket until the brackets are rmly secured.
Do not overtighten the tilt locking bolts.
Tilt
Locking
Bolts
16
Outdoor TV Mount Warranty
The standard limited warranty policies of Séura, Inc. (“Séura”)
shall apply to all equipment or other goods (“Products”) at the
time of sale to any authorized Séura distributor and/or product
reseller. These warranty policies may be modied by Séura
from time to time. Copies of the standard limited warranties
then in effect for a particular Product will be made available
upon request and are also available on the Séura website at
https://www.seura.com/warranty/. This warranty is valid only
with respect to Product sales in the U.S. and Canada.
If any Product fails to work or operate properly because of a
defect in materials or workmanship, Séura will, if notied of
such defect within the applicable warranty period indicated
below, at its option, either: (a) repair the Product with new or
refurbished parts onsite or at Séura’s factory, including Séura’s
labor if applicable; or (b) replace the Product with a new or
refurbished Product; or (c) if repair or replacement is not
commercially feasible, refund an amount equal to a pro rata
share of the current MSRP (as determined by the remainder
of the warranty period). The remedy chosen will be in good
faith and at the discretion of Séura. In no event will Séura be
responsible for any costs related to installation and/or removal
of Product.
Séura warrants its Products as set forth below, which warranty
periods shall start and run from the date of Séura’s sale of the
Product:
• Indoor and Outdoor Mounts for two (2) years against
defects in original hardware and/or workmanship.
Excludes corrosion or rust resulting from damaged,
scratched or chipped paint or other surfaces.
Exceptions to Warranty: This warranty is valid only with respect
to Product sales in the U.S. and Canada. Séura does not
warrant Products against defects arising out of, related to, or
caused by, whether totally or partially, and whether directly or
indirectly, any of the following:
A. Failing to properly clean and maintain, any Product, part
or component of a Product, including, but not limited to,
lters, front bezel, and other Product areas or components;
B. A Product’s extended use, including particularly,
commercial applications, where a Product is operating on
average more than twelve (12) hours per day on a permanent
or extended periodic basis;
C. Circumstances, damage (including concealed damage) or
other conditions occurring during shipment of a Product or
at any time after a Product leaves Séura’s facility (including
without limitation transport of the Product to or from Séura
before or after authorized service). Products must be packed
properly using original packaging or Séura replacement or
pre-authorized packaging. Customer assumes all risk, and
costs, including transportation costs, while Product is in
transit to or from Séura;
D. Circumstances, damage or other conditions occurring
during unpacking and/or removal of a Product from its
original packaging, including the removal of protective
material;
E. Improper, incorrect, or insufcient AC supply voltage to
a Product;
F. Alterations, modications, including use of unauthorized
mount, or changes to a Product without Séura’s prior written
authorization;
G. The incorporation of a Product into or within a product
of a third party, without Séura’s prior written authorization;
H. A Product’s misuse, neglect use, abuse, or improper
operation, including the failure to follow a Product’s normal
and ordinary operating instructions;
I. The effects of re, ood, lightning, electrical surges,
water and other liquid inltration, smoke, insect or animal
infestation, sand, mud, chemicals, improper cleaning agents
and other substances not intended to come into contact
with a Product, including any such substances contact with
a Product as the result of acts of God;
J. The improper or faulty installation, setup, or adjustment
of a Product;
K. A Product’s repair, attempted repair, or total or partial
disassembly by any party other than a Séura authorized
service representative;
L. When the Product occurs with pixel errors within the
specied and permitted area. (For more information about
this, inquire directly with Séura regarding the Séura Pixel
Policy.)
M. Corrosion that does not affect the performance of
a Product or the reasonable cosmetic appearance of a
Product (including without limitation, scratches or other
paint or nish damage to a Product that lead to or are
caused by, in part or in total, corrosion);
O. Normal wear and tear on the Product.
Séura does not warrant that its Products will integrate with any
third party products at present or in the future. It is purchaser’s
responsibility to test and verify compatibility. Further, Séura
does not warrant its software or programs, or any content
downloaded after shipment. It is the purchaser responsibility to
take precautions to protect the product from malware, viruses,
data loss, and other potentially destructive programs.
Warranty Disqualiers. This Limited Warranty only extends
to, and runs for the benet of, the original purchaser of the
Product and only covers a Product purchased new. All warranty
claims must be submitted together with original proof of
purchase and any Product subject to a warranty claim must
retain its original Séura serial number. Séura reserves the
right to require any warranty claimant to produce the original
purchase receipt or other original purchase date proof as may
17
be reasonably required by Séura to verify the Product’s warranty
eligibility. Séura shall have no liability with respect to Products
whose serial number has been removed, defaced, replaced, or
otherwise tampered with in any manner. Séura reserves the
right to examine all failed product components and determine,
in its sole discretion, whether any product components are
defective and covered under warranty.
LIMITATION OF LIABILITY. THE EXPRESS LIMITED WARRANTIES
SET FORTH HEREIN ARE IN LIEU OF ALL OTHER WARRANTIES,
WRITTEN OR ORAL, EXPRESSED OR IMPLIED, INCLUDING,
BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR
USE. SÉURA WILL NOT BE LIABLE FOR ANY DAMAGE TO OTHER
PROPERTY CAUSED BY ANY DEFECT IN THE PRODUCT, DAMAGES
BASED ON INCONVENIENCE, LOSS OF BUSINESS OPPORTUNITY,
LOSS OF GOODWILL, INTERFERENCE WITH BUSINESS
RELATIONSHIPS, OR OTHER COMMERCIAL LOSS, EVEN IF
THE CUSTOMER HAS BEEN ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. SÉURA WILL NOT BE LIABLE FOR ANY LOSS,
DAMAGE OR LIABILITY OR ANY DIRECT, INCIDENTAL, INDIRECT,
PUNITIVE, SPECIAL OR CONSEQUENTIAL DAMAGES RESULTING
FROM THE USE OR MISUSE OF A PRODUCT, OR ARISING OUT
OF ANY BREACH, BY THE PURCHASER OF A PRODUCT, OF
THIS LIMITED WARRANTY. SÉURA SHALL NOT BE LIABLE FOR
ANY CLAIM AGAINST THE CUSTOMER BY ANY OTHER PARTY.
SÉURA SHALL NOT BE LIABLE FOR ANY VERBAL WARRANTY
ASSURANCES MADE BY ANY EMPLOYEE OR AUTHORIZED
DISTRIBUTOR, RESELLER OR INSTALLER THAT CONFLICTS
WITH OR ENHANCES THE WRITTEN WARRANTY HEREIN. SOME
STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF
INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR LIMITATIONS
ON HOW LONG AN IMPLIED LIMITED WARRANTY LASTS, SO THE
EXCLUSIONS MAY NOT APPLY TO A PARTICULAR PURCHASER.
NOTWITHSTANDING ANYTHING HEREIN TO THE CONTRARY,
SÉURA’S MAXIMUM AGGREGATE LIABILITY RELATED TO ANY
WARRANTY CLAIM OR WITH RESPECT TO A PRODUCT SHALL
NOT EXCEED THE THEN CURRENT SÉURA WHOLESALE PRICE
OF THE SPECIFIC PRODUCT FROM WHICH THE CLAIM DERIVES.
NOTICE OF ANY WARRANTY CLAIM MUST BE RECEIVED BY
SÉURA, IN WRITING, PRIOR TO THE EXPIRATION OF THE
APPLICABLE WARRANTY PERIOD SET FORTH ABOVE. THE
PRODUCT WARRANTY APPLIES ONLY FOR THE PERIODS SET
FORTH ABOVE.
Warranty Procedure. A warranty claimant must contact Séura
at 920-857-9069 for a diagnostic. Please have your Product
receipt available. At that time, Séura will provide technical
support over the phone to attempt to x the problem. If
unsuccessful, a Séura Representative will determine if the
Product will be serviced onsite, replaced, or returned to Séura’s
factory in Green Bay, Wisconsin for repair. If Séura determines
that the Product is not covered under the warranty or damaged
in shipping, Séura will notify and inform the purchaser of service
alternatives that are available on a fee basis.
Toll-Free Technical Support: Please call 1-800-957-3872 to
speak with a Séura Technical Support Representative. Séura
Representatives are available Monday-Friday, 8:00am-4:30pm
Central Time.
Onsite Service: If Technical Support determines the problem
may be xed onsite, a Séura service agent will be scheduled
within 24 hours to service the unit. A Séura representative will
work with the customer to schedule a convenient time for onsite
service. Parts may be sent to the customer’s location. Onsite
service is available in the United States during normal business
hours Monday – Friday, unless other special circumstances exist
and special arrangements are made.
Factory Service: If Technical Support determines the Product
must be sent back to Séura’s factory for repair, the customer
must follow return instructions below. Séura will ship the
repaired Product to the authorized reseller, installer or
customer’s address. This warranty does not cover removal or
installation costs of Products.
Advanced Replacement: If Technical Support determines the
Product must be replaced, Séura will ship a new Product to
the authorized reseller, installer or customer’s address. The
customer must follow return instructions below to send the
damaged Product back to Séura’s factory. Credit card information
will be collected before shipment of the replacement Product.
If Séura does not receive the original Product back within thirty
(30) days of shipping the replacement Product, the credit card
on le will be charged at full MSRP. This warranty does not cover
removal or installation costs of Products.
Return Instructions: If return is necessary, Séura will issue a
return goods authorization (RGA) number and, if applicable,
specic return and shipping instructions. A Product will only
be accepted for warranty claims if returned and shipped to
Séura in the Product’s original packaging materials. If original
packaging is not available, please contact Séura to receive
authorized replacement packaging. Packages not bearing the
issued returned goods authorization (RGA) number will not be
accepted by Séura and will be returned to sender. In addition to
the Product, the package must include the warranty claimant’s
original sales receipt for the purchase of the Product. All Product
returns shall be received by Séura, at 1230 Ontario Road; Green
Bay, WI 54311 with freight prepaid by the warranty claimant.
Séura shall not be responsible for, and the warranty claimant
assumes and retains all such responsibility, any damage or loss
to or of the Product during shipment to and from Séura as the
result of a warranty claim.
Exclusive Remedy. This Limited Warranty sets forth the
exclusive remedies of a warranty claimant, and the exclusive
liabilities and obligations of Séura, with respect to allegations
of a defective Product.
19163121.3
18
Specications
SHORT ARM CEILING
MOUNT
Model: SC-1
LONG ARM CEILING
MOUNT
Model: LC-1
GENERAL
DISPLAY COMPATIBILITY 42" - 86" Séura Outdoor TVs
CEILING MOUNT DIMENSIONS
Collapsed: 26.25” w x 6.6 d x 34” h
Extended: 26.25” w x 6.6 d x 42” h
Collapsed: 26.25” w x 6.6 d x 48.5” h
Extended: 26.25” w x 6.6 d x 70.5” h
MOUNTING PLATE
DIMENSIONS
6.5" w x 6.5" h 6.5” w x 6.5” h
FINISH COLOR Black Powder Coat
DURABILITY Acrylic E-Coated Steel
INSTALLATION
MAXIMUM TV WEIGHT 200 lbs
INSTALLATION SURFACE
Wood / Concrete / Steel
HARDWARE Stainless Steel
SHIPPING
SHIPPING CONTAINER DIMS
19" w x 27" l x 5.25" h 19" w x 36.5" l x 5.25" h
SHIPPING WEIGHT
30 lbs 36 lbs
PRODUCT WEIGHT 24 lbs 30 lbs
Maximum TV Weight: 200 lbs.
The wall structure must be capable of supporting at least ve times the weight of the TV. If not, the wall
structure must be reinforced.
14
15
16
" FULLY COLLAPSED
22-15/16" FULLY EXTENDED
17
15
16
"
25mm
1"
5
16
" X
13
16
"
4
1
8
"
4
7
8
"
5"
5
3
4
"
6
1
2
"
6
1
2
"
4
5
16
"
29
7
16
" FULLY COLLAPSED
51-7/16" FULLY EXTENDED
17
15
16
"
25mm
1"
4
5
16
"
17
15
16
"
25mm
1"
Optiona l: Using the keyhol e locations, dr ill
the addit ional holes for t he support screw s.
Insert a nd fasten two sc rews without
washers until approximately 1/2" remains.
O
p
t
i
o
n
a
l
K
e
y
h
o
l
e
S
l
o
t
O
p
t
i
o
n
a
l
K
e
y
h
o
l
e
S
l
o
t
19
14
15
16
" FULLY COLLAPSED
22-15/16" FULLY EXTENDED
17
15
16
"
25mm
1"
5
16
" X
13
16
"
4
1
8
"
4
7
8
"
5"
5
3
4
"
6
1
2
"
6
1
2
"
4
5
16
"
29
7
16
" FULLY COLLAPSED
51-7/16" FULLY EXTENDED
17
15
16
"
25mm
1"
4
5
16
"
17
15
16
"
25mm
1"
Optiona l: Using the keyhol e locations, dr ill
the addit ional holes for t he support screw s.
Insert a nd fasten two sc rews without
washers until approximately 1/2" remains.
O
p
t
i
o
n
a
l
K
e
y
h
o
l
e
S
l
o
t
O
p
t
i
o
n
a
l
K
e
y
h
o
l
e
S
l
o
t
14
15
16
" FULLY COLLAPSED
22-15/16" FULLY EXTENDED
17
15
16
"
25mm
1"
5
16
" X
13
16
"
4
1
8
"
4
7
8
"
5"
5
3
4
"
6
1
2
"
6
1
2
"
4
5
16
"
29
7
16
" FULLY COLLAPSED
51-7/16" FULLY EXTENDED
17
15
16
"
25mm
1"
4
5
16
"
17
15
16
"
25mm
1"
Optiona l: Using the keyhol e locations, dr ill
the addit ional holes for t he support screw s.
Insert a nd fasten two sc rews without
washers until approximately 1/2" remains.
O
p
t
i
o
n
a
l
K
e
y
h
o
l
e
S
l
o
t
O
p
t
i
o
n
a
l
K
e
y
h
o
l
e
S
l
o
t
SHORT ARM
CEILING MOUNT
Model: SC-1
LONG ARM
CEILING MOUNT
Model: LC-1
Publish date: September 15, 2020
Information is subject to change without notice.
© 2020 Séura
1230 Ontario Road Green Bay, Wisconsin 54311
1-800-957-3872 contacts@seura.com
www.seura.com
94-060500
For technical support, please contact Séura at
1-800-957-3872 during regular business hours:
M-F 8:00 am - 4:30 pm, Central Time.
Produkt Specifikationer
| Mærke: | Séura |
| Kategori: | Ikke kategoriseret |
| Model: | SC-1 |
Har du brug for hjælp?
Hvis du har brug for hjælp til Séura SC-1 stil et spørgsmål nedenfor, og andre brugere vil svare dig
Ikke kategoriseret Séura Manualer
30 August 2024
30 August 2024
30 August 2024
30 August 2024
30 August 2024
30 August 2024
30 August 2024
30 August 2024
Ikke kategoriseret Manualer
- Spear & Jackson
- Profilo
- MDT
- Lasita Maja
- Synco
- Draytek
- Hitron
- Primewire
- Asetek
- Edsyn
- Trumeter
- Jay-tech
- ESX
- Hori
- Cotek
Nyeste Ikke kategoriseret Manualer
15 Juli 2025
15 Juli 2025
15 Juli 2025
15 Juli 2025
15 Juli 2025
15 Juli 2025
15 Juli 2025
15 Juli 2025
15 Juli 2025
15 Juli 2025