Shure 515 Manual

Shure Mikrofon 515

Læs gratis den danske manual til Shure 515 (4 sider) i kategorien Mikrofon. Denne vejledning er vurderet som hjælpsom af 60 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 30.5 anmeldelser. Har du et spørgsmål om Shure 515, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

General Description

515SBGX

515SBG-18X

The Shure Models 515SBGX, 515SBG-18X, and 515SBG-18XF microphones

are low-impedance dynamic microphones designed to be mounted on flexible

goosenecks or fixed pips. Optimized frequency response and a unidirectional

(cardioid) pickup pattern makes them ideal for language labs, paging appli-

cations, and base station communications. They are also recommended for

use as talkback or cuing microphones in TV, film, and recording studios.

Because of their low impedance, these microphones retain their level and

response characteristics even when long lengths of cable are used.

All three models are supplied with a push-to-talk button and a four-conductor

cable (two conductors shielded).

Features

• Frequency response optimized for announcing, narration, and paging

applications

• Cardioid pickup pattern symmetrical about axis

• Neodymium magnet for high signal-to-noise ratio

• Shock-mounted cartridge for quiet operation and low stand/handling

noise

• Tough diecast locking grille and handle

• Built-in push-to-talk button controls microphone circuit and relay or control

circuit

• 45.7 cm (18 in.) gooseneck and mounting flange supplied (515SBG-18X

and 515SBG-18XF only)

Variations

Model 515SBGX: Does not include gooseneck or mounting flange.

Model 515SBG-18X: Includes gooseneck and 76.2 mm (3 in.) diameter

mounting flange.

Model 515SBG-18XF: Includes gooseneck and 44.4 mm (1-3/4 in.) diameter

mounting flange.

Mounting the 515SBG-18X and 515SBG-18XF

Mount the 515SBG-18X or 515SBG-18XF as follows:

1. Thread the supplied hexnut all the way down on the mounting flange.

2. Thread the gooseneck tightly on the flange.

3. Back the hexnut up against the gooseneck, and use a wrench to tighten

the nut firmly against the bottom of the gooseneck.

Mounting the 515SBX onto a Gooseneck

Mount the 515SBGX onto a gooseneck or fixed pipe with a 5/8 in- 27 thread

as follows:

1. Unscrew the black end cap from the microphone.

2. Remove the thin metal washer and the metal spacer.

3. Re-install the washer by sliding it back onto the cable and up into the

end of the microphone.

4. Slip the cable into the gooseneck or pipe and thread the microphone

firmly to the mount.

For additional service or parts information, please contact Shure's Service

department at 1-800-516-2525. Outside the United States, please contact

your authorized Shure Service Center.

Connections

These low-impedance microphones are designed for connection to microphone inputs rated at 75 to 300 ohms. Using balanced-line low-impedance cables

permits very long cable lengths without affecting response or level. The RED and BLACK cable leads are the microphone conductors for balanced-line connections;

the shield is connected to the amplifier ground.

For unbalanced operation, connect the BLACK lead to the shield, and use the RED lead as the microphone conductor.

The GREEN and WHITE cable leads are used to control an external relay or control circuit.

1/4 in. Phone PlugXLR ConnectorFunctionWire ColorInput Type

TipPin 2AudioRed

Unbalanced

SleevePin 3Audio GroundBlack

515SBGX

Voice Communication Microphones