Shure 545SD Manual
Læs gratis den danske manual til Shure 545SD (5 sider) i kategorien Mikrofon. Denne vejledning er vurderet som hjælpsom af 11 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 6 anmeldelser. Har du et spørgsmål om Shure 545SD, eller vil du spørge andre brugere om produktet?
Side 1/5

1/5
545SD -- Vocal Microphone
General Description
The Model 545SD is a dual-impedance, unidirec-
tional, dynamic microphone. Shipped connected
for low-impedance operation, it features a silent
magnetic reed on/off switch.
The Classic Unidyne is a favorite for instrument
pickup and recording,and can be used on
lecterns for public address systems such as
those used in political conventions and legisla-
tures, convention halls, hotels, public auditori-
ums, stadiums, schools, and churches.
Features
•Exceptionally uniform cardioid pattern minimizes feedback in PA applications
•Selectable dual-impedance operation
•Silent magnetic reed on/off switch with lock option
•Cardioid dynamic
•Frequency response: 50 to 15,000 Hz
Connections
When using the microphone with a balanced input, pins 2 and 3 are the audio signal carriers. When using the mi
crophone with an unbalanced input, use a cable wired with pin 2 as the signal carrier and pin 3 connected to the
cable shield (ground), such as the Shure C20AHZ high-impedance cable.

Shure Incorporated
2/5
Impedance Selection
The microphone is shipped connected for low impedance operation. To change to high impedance, proceed as fol
lows:
1. Remove plug element at receptacle end of microphone by turning slotted setscrew in (counterclockwise) and
carefully withdrawing plug element from case.
2. Disconnect 2-terminal impedance selection socket from rear of plug element.
3. Reconnect 2-terminal impedance selection socket in reverse position so that pin 3 of plug element is inserted
in socket terminal "H" (White).
4. Reassemble plug element into microphone and seal setscrew securely by turning out (clockwise).
IMPEDANCE SELECTION RECEPTACLE END OF MICROPHONE
Polarity
All cables and microphones should be tested to ensure that they have the same polarity. To test two microphones
and/or their cables for proper polarity, connect them to an amplifier and talk or sing into them while holding them
three or four inches apart. The sound from the speakers should be the same when talking into either microphone
or directly between them. If the sound drops drastically, or if a dead spot is found when talking between the two mi
crophones, either the microphones or their cables have opposite polarity.
To change the polarity of a microphone cable, either use a Shure A15PRS phase reverser or interchange the wires
connected to pins 2 and 3 of the threepin connector at one end of the cable. To change the polarity of a micro
phone, the microphone cartridge leads must be interchanged. This should be performed by your dealer, the Shure
Factory Service Department, or other qualified service personnel.
Specifications
Type
Dynamic (moving coil)
Frequency Response
50 to 15,000 Hz
Produkt Specifikationer
Mærke: | Shure |
Kategori: | Mikrofon |
Model: | 545SD |
Har du brug for hjælp?
Hvis du har brug for hjælp til Shure 545SD stil et spørgsmål nedenfor, og andre brugere vil svare dig
Mikrofon Shure Manualer
22 Juli 2025
15 Juli 2025
23 Juni 2025
21 Februar 2025
21 Februar 2025
29 December 2024
29 December 2024
29 December 2024
29 December 2024
29 December 2024
Mikrofon Manualer
- Speco Technologies
- Shadow
- AVerMedia
- ANT
- Triton
- Manta
- Catchbox
- MILAB
- Prodipe
- Sandberg
- Tascam
- Axis
- Majority
- Palmer
- Mars Gaming
Nyeste Mikrofon Manualer
15 August 2025
15 August 2025
14 August 2025
14 August 2025
14 August 2025
14 August 2025
13 August 2025
13 August 2025
13 August 2025
13 August 2025