Shure MX391 Manual

Shure Mikrofon MX391

Læs gratis den danske manual til Shure MX391 (16 sider) i kategorien Mikrofon. Denne vejledning er vurderet som hjælpsom af 16 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 8.5 anmeldelser. Har du et spørgsmål om Shure MX391, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/16
Printed in U.S.A.
www.shure.com
© 2009 Shure Incorporated
27A14048 (Rev. 1)
MX391 Series
MX391
2
Shure Microflex® MX391 Series microphones
are small, surface-mounted electret condenser
microphones designed for mounting on confer-
ence tables, stage floors, and lecterns. Their
high sensitivity and wide frequency range make
them especially suitable for picking up speech
and vocals in sound reinforcement and recording
applications.
Features
• Flat frequency response across the vocal range
for uncolored sound
• Interchangeable cartridges that provide a
choice of polar pattern for each application
• Sleek, low-profile design for unobtrusive
appearance
• RF filtering
Model Variations
Microflex MX391 microphones are available in
black or white.
The polar pattern of the included cartridge is indi-
cated by a model number suffix:
/C Cardioid
/S Supercardioid
/O Omnidirectional
Interchangeable Cartridges
Microflex microphones
use interchangeable car-
tridges that allow you to
choose the polar pattern
for different installations.
Surface Mount
Microphones
R183 Omnidirectional
R184 Supercardioid
R185 Cardioid
Microphone Placement
For best low-frequency response and rejection
of background noise, place the microphone on
a large, flat surface, such as a floor, table, or
lectern.
To reduce reverberance, avoid reflective surfaces
above or to the side of the microphone, such as
beveled sides of pulpits or overhanging shelves.
PREAMP
Preamp Gain
If necessary, the preamplifier gain can be reduced
by 12 dB. Contact an authorized Shure service
center for information.
RFI Filtering
Important: Microphones must be used with the
RK100PK preamp to optimize RF immunity.
Permanent Installation
1. Remove grille.
2. Place housing in position and mark location of
screw holes and bottom cable exit hole.
3. Drill starter hole for each screw and a 1/2 in.
bottom exit hole for the mic cable.
4. Insert 4-pin mini-connector and cable through
cable hole.
5. Replace grille with screw. Do not overtighten.
Do not attempt to detach the cable from the mi-
crophone, as damage may result.

Produkt Specifikationer

Mærke: Shure
Kategori: Mikrofon
Model: MX391

Har du brug for hjælp?

Hvis du har brug for hjælp til Shure MX391 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Mikrofon Shure Manualer

Shure

Shure MoveMic One Manual

21 Februar 2025
Shure

Shure MV7i Manual

21 Februar 2025
Shure

Shure VP89M Manual

29 December 2024
Shure

Shure PGA DRUMKIT4 Manual

29 December 2024
Shure

Shure PGA DRUMKIT6 Manual

29 December 2024
Shure

Shure Microflex MX395 Manual

29 December 2024
Shure

Shure KSM11 Manual

29 December 2024
Shure

Shure GLXD+FM Manual

23 December 2024
Shure

Shure MoveMic Manual

17 November 2024
Shure

Shure MXA901-R Manual

6 September 2024

Mikrofon Manualer

Nyeste Mikrofon Manualer

Rane

Rane GM 16 Manual

15 Juni 2025
Kogan

Kogan KAGMICBOMLA Manual

15 Juni 2025
Omnitronic

Omnitronic UHF-601 Manual

14 Juni 2025
Omnitronic

Omnitronic UHF-604 Manual

14 Juni 2025
Omnitronic

Omnitronic UHF-602 Manual

14 Juni 2025
Neewer

Neewer VM11 Manual

14 Juni 2025
Neewer

Neewer KM23 Manual

13 Juni 2025
AmpliVox

AmpliVox S1695 Manual

13 Juni 2025
Comica

Comica BooMax Manual

12 Juni 2025
DNA

DNA UWM 1 Manual

9 Juni 2025