Shure UA874Z Manual

Shure Ikke kategoriseret UA874Z

Læs gratis den danske manual til Shure UA874Z (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 22 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 11.5 anmeldelser. Har du et spørgsmål om Shure UA874Z, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

General Description

The Shure UA874 uses a log periodic dipole array to offer enhanced reception

when directed toward the desired coverage area. An integrated amplifier and

four gain settings compensate for varying degrees of coaxial cable signal

loss. The UA874 can be mounted on a microphone stand, suspended from

the ceiling, or mounted to a wall using the integrated swivel adapter.

Features

• Low-noise signal amplifier compensates for insertion loss in coaxial cable

• Compatible with Shure wireless receivers and antenna distribution sys-

tems that provide 10–15 V DC bias

• Integrated threaded adapter mounts easily to microphone stands

• Four-position gain selector switch

• Shure quality, ruggedness, and reliability

Note: will not operate The antenna without 10-15 V DC bias. This is required

even at -6 dB and 0 dB ("passive") gain settings.

Installation

• Connect the antenna to the receiver or distribution system using Shure

antenna cables (or any 50 ohm, low-loss coaxial cable, such as RG-8U).

• The antenna only operates with receivers or distribution systems that

provide 10–15 V DC bias.

• Lower the gain setting for short cable runs, or increase gain for longer

runs. Note that the quality of the cable, not just the length, contributes

to signal loss. A lighter-grade 50 foot cable may require more gain than

a 100 foot, low-loss cable. Contact the cable manufacturer for cable loss

specifications.

• Direct the antenna toward the intended coverage area.

• Do not use this antenna for transmitting (such as with PSM transmitters)

Cable Maintenance

To maintain top performance for antenna cables:

• Avoid sharp bends or kinks in the cables.

• Do not deform cables with makeshift clamps, such as bending a nail over

the cable.

• Do not use in permanent outdoor installations.

• Do not expose to extreme moisture.

Selecting Antenna Cables

Use 50 ohm low-loss coaxial cable, such as RG-8U. Shure offers pre-termi-

nated antenna cables ranging from 6 to 100 feet.

NOTE: When ordering cables from Shure, select the low-loss "Z" models

(available for longer cables) when using frequency bands above 1000 MHz.

Interface

① Gain Switch

Adjust the four-position gain switch to compensate for the calculated cable loss, based on the length and type of cable.

Caution: There may be a small RF dropout when changing the gain setting.

UA874Z

Active Directional Antenna

② Gain Mode LED

Indicates the current gain switch setting.

③ RF Overload LED

Indicates a strong RF signal that is overloading the antenna amplifier, which results in distortion or poor performance. Increase the distance between the antenna

and transmitter, or lower the antenna gain setting.

NOTE: RF Overload LED does not operate for passive gain settings (−6 dB or 0 dB).

④ BNC Connector

Connect to a receiver or antenna combiner with RF inputs that supply 10–15 V DC bias.

Antenna Placement

Use the following guidelines when mounting antennas:

• Antennas and receivers must be from the same band.

• Mount antennas one wavelength (two feet) apart.at least

• Position antennas so there is nothing obstructing a line of sight to the transmitter (including the audience).

• Keep antennas away from metal objects.

Important: Always perform a "walk around" test to verify coverage before using a wireless system during a speech or performance. Experiment with antenna

placement to find the optimum location. If necessary, mark "trouble spots" and ask presenters or performers to avoid those areas.

Shure IncorporatedUA874Z Active Directional Antenna

2017/11/022/4