Shure WA333 Manual

Shure Ikke kategoriseret WA333

Læs gratis den danske manual til Shure WA333 (1 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 11 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 6 anmeldelser. Har du et spørgsmål om Shure WA333, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

WA333 TA4F Adapter Instruction Sheet

27A11874 (Rev. 1) Printed in U.S.A.

Step 5

Shortening the Cable: With all new MX models being connected to the in-line preamp with a TA4F connector, it is now more difcult for an installer

to shorten the cable length. In order to change the cable length, the existing TA4F adapter must be removed, cable must be shortened, and a new

TA4F adapter must be reattached. Most TA4F parts can be reused. Installer will need to purchase a new ferrule (P/N 31A2135) in order to sucessfully

reattach adpater with ensured immunity.

Step 1: Loosen the hex set screw using a .038 hex wrench and remove the existing TA4F connector housing.

Step 2: Shorten cable to desired length. Carefully strip cable, removing the sheath.

Step 3: Loosen the copper shield/GND. Using a pointed tip, carefully unbraid strands and comb copper so it is straight.

Step 4: Comb the unbraided copper strands back against the cable and make sure copper is evenly distributed around the

cable. Strip and tin the +/- connections.

Step 5: Insert the ferrule over the copper cable, small side down. Slide the ferrule over the cable up to the bottom edge of the cup.

Step 6: Using a hexagonal .128 crimping tool, crimp the ferrule onto the cable. Make sure not to over crimp.

Step 7: Trim excess copper.

Step 8: Insert TA4F spacer and solder audio wires to TA4F.

Step 9: Twist TA4F receptacle to tighten slack.

Step 10: Reattach TA4F connector housing and tighten the hex set screw.

Diagram for Step 8

Step 6

IMPORTANT: Make sure copper does not come into the cup. Do not twist the ferrule.

Step 2

Step 8

TA4F Spacer

TA4F Receptacle

Step 7

Step 1

connector housing

Step 4

Step 3

Shield Note 2

0.725 ± 0.031

[18.42 ± 0.79]

0.575 ± 0.031

[14.60 ± 0.79]

ferrule

.038 hex wrench

0.100

[2.5]

0.150

[3.8]

Produkt Specifikationer

Mærke:	Shure
Kategori:	Ikke kategoriseret
Model:	WA333
Antal pr. pakke:	1 stk
Produktfarve:	Sort
Stik:	4-Pin (TA4F)
Stik køn:	Hunstik
Forbindelsesformfaktor:	Lige

Har du brug for hjælp?

Hvis du har brug for hjælp til Shure WA333 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Shure Manualer

Shure MoveMic MV-R Manual

21 Februar 2025

16 December 2024

2 December 2024

2 December 2024

2 December 2024

2 December 2024

Shure A910-HCM Manual

1 December 2024

Shure A50D Manual

1 December 2024

Shure A710-FM Manual

1 December 2024

Shure A75M Manual

1 December 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Lightspeed 975 Manual

15 Juni 2025

Planet Audio P90CPA Manual

15 Juni 2025

Tefal Aroma BH4391 Manual

15 Juni 2025

Bradley S19214FW Manual

15 Juni 2025

incubato IN-96DDI Manual

15 Juni 2025

Levenhuk SkyMatic 135 GTA Manual

15 Juni 2025

Milwaukee MPS Manual

15 Juni 2025

Planet Audio PC45RGB Manual

15 Juni 2025

Ecler PULSO-10 Manual

15 Juni 2025

Marshall CV355-30X-NDI Manual

15 Juni 2025