Silicon Power SP008GBLFU240B02 Manual

Silicon Power Ingen kategori SP008GBLFU240B02

Læs gratis den danske manual til Silicon Power SP008GBLFU240B02 (2 sider) i kategorien Ingen kategori. Denne vejledning er vurderet som hjælpsom af 25 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 13 anmeldelser. Har du et spørgsmål om Silicon Power SP008GBLFU240B02, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Silicon Power LONG-DIMM Installation Guide

Silicon Power manufactures LONG-DIMM DRAM for use in desktop PCs. The instructions on

this page provide general installation and handling information are to be used in conjunction

with your computer's model-specific Owner's Manual.

Installation Procedures

1. Place your computer’s power switch in the off position and disconnect the AC power cord.

2. Follow the instructions in your computer’s Owner's Manual, open the computer’s case to

gain access to the memory module expansion sockets on the motherboard.

3. Check your Owner’s Manual to determine the correct installation sequence for your

computer.

4. To insert the module into an available expansion socket on the motherboard, note how the

module is keyed to the socket. This insures the module can be plugged into the socket one

way only. Firmly press the module into position making certain the module is completely

seated in the socket and the retaining clips have snapped up to lock the module into the

socket.

5. To remove a module, press down on the retaining clips at each end of the module to cause

it to pop-up within the socket for removal.

6. After the module or modules have been installed, close the computer case; reinstall any

cables disconnected during the installation process; and, plug in the AC power cord.

7.Turn on your computer and follow the instructions in your computer’s Owner's Manual to

configure the computer to recognize the new installed Memory or internal computer

component.

Note:

Electrostatic discharges can damage your memory and computer. Touch a grounded,

metal surface before handling your memory or internal computer components

Silicon Power SO-DIMM Installation Guide

Silicon Power manufactures SO-DIMM DRAM for use in notebook computers. The instructions

on this page provide general installation and handling information are to be used in conjunction

with your computer's model-specific Owner's Manual.

Installation Procedures

1. Place your notebook computer’s power switch in the off position, disconnect the AC power

cord, and remove the rechargeable battery to prevent damage during memory installation.

Refer to your computer’s Owner’s Manual for specific details.

2. Follow the instructions in your Owner's Manual to obtain access to your computer’s

memory expansion socket or sockets.

3. Handle your new memory module carefully; do not flex or bend it. Always grasp the

module by its edges.

4. Your memory module and the expansion socket are keyed .A small plastic bridge in the

socket must align with the notch in the module .The keyed bridge and notch ensures that

the module can be plugged into the socket one way only.

5. Insert your memory module into the socket at a 30-45 degree angle. Make sure the notch

and the module are properly aligned.

6. Once the module is properly aligned with the socket, rotate the module downwards until the

clips at each end of the expansion socket click into place. To remove the module from an

expansion socket, place your thumbs on each of the clips located on both sides of the

socket, and press apart to the left and right away from the module. The SO-DIMM module

should spring upward. Remove it at the same angle it was inserted.

7. After installing your module or modules, close the computer case; reinstall any cables that

may have been disconnected during the installation process; and, plug in the AC power

cord/replace the rechargeable battery.

8.Turn on your computer and follow the instructions in your Owner's Manual to configure the

computer to recognize the new Memory.

Note:

Electrostatic discharge can damage your memory and access to your computer's

memory expansion socket or computer. Touch a grounded metal surface before

sockets. Handling your memory or internal computer component

 For illustrations regarding installation, please refer to the Chinese installation guide.

Produkt Specifikationer

Mærke:	Silicon Power
Kategori:	Ingen kategori
Model:	SP008GBLFU240B02
Intern hukommelse:	8 GB
Intern hukommelsestype:	DDR4
Hukommelsesur hastighed:	2400 MHz
Hukommelse form faktor:	288-pin DIMM
Komponent til:	PC/server
Fejlkorrigerende kode:	Ja
Hukommelsesspænding:	1.2 V
Hukommelseslayout (moduler x størrelse):	1 x 8 GB
Maksimal blænderåbning:	17
Pufret hukommelsestype:	Unregistered (unbuffered)